TRENDnet TEG-S2620is Manuel utilisateur
H/W: V1
TEG-S2620is
Quick Installation Guide
Table of Contents
English ......................................................................................................
Troubleshooting .........................................................................................
1
1
3
2
6
1. Before You Start
2. Hardware Installation ........................................................................
3. Configure the Switch .........................................................................
................................................................................
Table of Contents
Version 04.04.2009
System Requirements
Optional Equipment
Application
Package Contents
1. Before You Start
English
1
?
?Multi-Language Quick Installation
Guide
?User's Guide CD-ROM
?RS-232 cable
?Power Cord
?Rack Mount Kit
?Rubber Feet
TEG-S2620is
?
?A computer with a network adapter properly installed
?A RJ-45 network cable
Web Browser: Internet Explorer (6 or 7)
?
?Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,
TEG-MGBS80, TEG-MGBS10D35, TEG-MGBS40D35) for Mini-GBIC slots.
EIA standard 19” rack
24-Port 10/100Mbps Layer 2 Stackable Switch with
2 shared Gigabit Ports and Mini-GBIC Slots
(TEG-S2620is)
RS-232
Workstation with
10/100Mbps PCI Adapter
(TE100-PCIWN)
Workstation
Multi-Mode Fiber
Mini-GBIC Modules
(TEG-MGBSX)
Multi-Mode Fiber
Mini-GBIC Modules
(TEG-MGBSX)
Workstation with
PCI Adapter
(TEG-PCITXR)
1000MbpsFiber 10/100Mbps
2. Hardware Installation
English
2
2. Connect a RJ-45 network cable
from the computer to an available
Ethernet port on the TEG-S2620is.
3. Verify that the following panel lights
are on: POWER and LINK/ACT.
1. Connect the Power Cord to
the TEG-S2620is and then to a
power outlet.
Note: The Mini-GBIC slots are shared with port 25 and 26 Gigabit Ethernet ports.
When the Mini-GBIC slots are in use, port 25 and 26 Gigabit Ethernet ports are
disabled.
English
3
3. Configure the Switch
Note: It is recommended that you configure the Switch from a wired computer.
Before the Switch can be configured, a Static IP address must be assigned to
your computer's network adapter in the subnet of 192.168.0.x. Since the
Switch's default IP address is 192.168.0.1, make sure no other network
devices are assigned an IP address of 192.168.0.1. (Refer to Troubleshooting
section on how to configure TCP/IP settings on your PC.)
Web Browser
1. Open your web browser, type
http://192.168.0.1 in the Address
bar, and then press Enter.
3. Select the desired options for
configuring the SNMP switch.
2. Enter the User Name and
Password, and then click OK.
By default:
User Name: admin
Password: admin
English
4
HyperTerminal
2. Go to Start -> Programs ->
Accessories -> Communications ->
HyperTerminal.
3. Enter a name, choose an icon and
then click OK.
4. Select the correct COM port (e.g.
COM1, COM2) and then click OK.
1. Connect the RS-232 cable from a
serial port on your Windows PC to
the console port on your computer.
English
5
6. Press Enter.
8. Press Enter.
Your configuration is now complete.
For detailed information regarding the TEG-S2620is’s configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
7. Enter the User Name.
By default:
User Name: admin
7. Enter the Password, and then
press Enter. By default:
password: admin
5. Configure the following setting,
click Apply and then click OK:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
6
Troubleshooting
Q1: How do I configure TCP/IP settings on my computer?
Q2:
A2:
I typed http://192.168.0.1 in my Internet Browser's Address Bar, but an error message
says “The page cannot be displayed.” How can I get into the TEG-S2620is's web
configuration page?
First, check your hardware settings again by following the instructions in section 2.
Second, make sure the Power and LNK/ACT lights are lit. Third, make sure the TCP/IP
settings are configured properly (see Q1). Fourth, since the Switch's default IP address is
192.168.0.1, make sure that no other network devices are assigned an IP address of
192.168.0.1.
1. Go into the Control Panel, click Network and
Internet, click Network and Sharing Center, click
Manage Network Connections and then right-click
the Local Area Connection icon and then click
Properties.
1. Go into the Control Panel, double-click the Network
Connections icon, and then right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4) and
then click Properties. Then click on Use the
following IP address, and make sure you assign
your network adapter an IP address in the subnet of
192.168.0.x.
Windows Vista
Windows XP/2000
1. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following IP
address, and make sure you assign your network
adapter an IP address in the subnet of 192.168.0.x.
Q3:
Q4:
Q5:
A5:
If my network's IP is different than the Switch's range, what should I do?
You should still configure the Switch first. After all the settings are applied, go to the Switch's
configuration page, click on Administrator, click IP Configuration, change the IP address of the
Switch to match your network's IP and then click Apply.
What are the default port settings for configuring the Switch through the console port
using HyperTerminal?
Bits per Second: 9600; Data bits: 8; Parity: None; Stop bits: 1; Flow control: None.
I changed the IP address of the switch, but I forgot it. How do I reset my TEG-S2620is?
Follow the instructions below:
1) Connect the RS-232 cable from a serial port on your Windows PC to the console port on
your computer.
2) Go to Start -> Programs -> Accessories -> Communications -> HyperTerminal.
3) Enter a name, select an icon and then click OK.
4) Select the correct COM port (e.g. COM1, COM2) and then click OK.
5) Configure the following settings, click Apply and then click OK:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
6) Press Enter.
7) Enter the user name. By default, the user name is admin.
8) Press Enter.
9) Enter the password. By default, password is admin.
10) Press Enter.
11) Press Tab to navigate to System Reset Configuration and then press Enter.
12) Press Tab to navigate to Factory Default and then press Enter.
13) Press Yto continue.
The default IP address of the switch is 192.168.0.1.
If you still encounter problems or have any questions regarding the TEG-S2620is, please contact
TRENDnet's Technical Support Department.
A3:
A3:
7
8
Limited Warranty
- 5-Year Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.
TEG-S2620is
If a product does not operate as warranted above during the applicable warranty period,
TRENDnet shall, at its option and expense, repair the defective product or deliver to
customer an equivalent product to replace the defective item. All products that are
replaced will become the property of TRENDnet. Replacement products may be new or
reconditioned.
TRENDnet shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to
service the product through any unauthorized service center. This warranty is voided if
(i) the product has been modified or repaired by any unauthorized service center, (ii) the
product was subject to accident, abuse, or improper use (iii) the product was subject to
conditions more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within the applicable
warranty period for a Return Material Authorization (RMA) number, accompanied by a
copy of the dated proof of the purchase. Products returned to TRENDnet must be pre-
authorized by TRENDnet with RMA number marked on the outside of the package, and
sent prepaid, insured and packaged appropriately for safe shipment.
Autres manuels pour TEG-S2620is
2
Table des matières
Autres manuels TRENDnet Changer
TRENDnet
TRENDnet TK-207K - KVM Switch - USB Manuel utilisateur
TRENDnet
TRENDnet TK-408K Manuel utilisateur
TRENDnet
TRENDnet TPE-TG80G Manuel utilisateur
TRENDnet
TRENDnet TEG-S2400I - DATA SHEETS Manuel d'installation et d'exploitation
TRENDnet
TRENDnet TE-500plus Manuel utilisateur
TRENDnet
TRENDnet TU2-700 - DATA SHEETS Manuel utilisateur
TRENDnet
TRENDnet TEG-7080ES Manuel utilisateur
TRENDnet
TRENDnet TPE-224WS - Web Smart PoE Switch Manuel utilisateur
TRENDnet
TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manuel utilisateur
TRENDnet
TRENDnet TPE-TG80G Manuel utilisateur
TRENDnet
TRENDnet TE100-S32plus Manuel utilisateur
TRENDnet
TRENDnet TEG-S50G Manuel utilisateur
TRENDnet
TRENDnet TPE-S44 - Switch Manuel d'installation et d'exploitation
TRENDnet
TRENDnet TE100-S1212 Manuel utilisateur
TRENDnet
TRENDnet TPE-224WS - Web Smart PoE Switch Manuel utilisateur
TRENDnet
TRENDnet TEG-S224M Manuel utilisateur
TRENDnet
TRENDnet TPE-TG50g Manuel utilisateur
TRENDnet
TRENDnet TPE-TG82ES Manuel utilisateur
TRENDnet
TRENDnet TE100-H24R Manuel utilisateur
TRENDnet
TRENDnet TUC-H4E Manuel utilisateur
