TRENDnet TE100-S16Eplus Manuel utilisateur
TE100-S16E
16-Port
10/100Mbps NWay
Ethernet Switch
User’s Guide
FCC Warning
This equipment has been tested and found to comply
with the regulations for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with this user’s guide, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful
interference, in which case the user will be required to
correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment,
this product may cause radio interference, in which
case the user may be required to take adequate
measures.
P/N:6012-3216101 Rev.A1-01
i
TABLE OF CONTENTS
ABOUT THIS GUIDE................................................III
PURPOSE......................................................................................III
TERMS/USAGE..........................................................................III
OVERVIEW OF THIS USER’S GUIDE.................................III
INTRODUCTION............................................................1
FAST ETHERNET TECHNOLOGY..........................................1
SWITCHING TECHNOLOGY....................................................2
FEATURES .....................................................................................3
UNPACKING AND SETUP...................................6
UNPACKING.................................................................................6
SETUP .............................................................................................7
IDENTIFYING EXTERNAL
COMPONENTS.................................................................8
FRONT PANEL .............................................................................8
REAR PANEL................................................................................9
LED INDICATORS ...................................................................10
ii
CONNECTING THE SWITCH.......................12
PC TO SWITCH..........................................................................12
HUB TO SWITCH.......................................................................12
A. 10BASE-T Hub..............................................................13
B. 100BASE-TX Hub........................................................13
HUB WITHOUT UPLINK (MDI-II) PORT.........................13
A. Using straight cable .......................................................14
B. Using crossover cable...................................................14
SWITCH TO SWITCH (OTHER DEVICES)..........................14
A. Using straight cable .......................................................14
B. Using crossover cable...................................................14
PORT SPEED & DUPLEX MODE.........................................15
TECHNICAL SPECIFICATIONS...............17
RJ-45 PIN SPECIFICATION............................19
iii
ABOUT THIS GUIDE
Congratulations on your purchase of the 16-port
10/100Mbps NWay Fast Ethernet Switch. This device
integrates 100Mbps Fast Ethernet and 10Mbps
Ethernet network in a highly flexible desktop package.
Purpose
This manual discusses how to install your 16-port
10/100Mbps NWay Fast Ethernet Switch.
Terms/Usage
In this guide, the term “Switch” (first letter upper
case) refers to your 16-port 10/100Mbps NWay Fast
Ethernet Switch, and ”switch” (first letter lower case)
refers to other Ethernet switches.
Overview of this User’s Guide
Chapter 1, Introduction. Describes the Switch and its
features.
Chapter 2, Unpacking and Setup. Helps you get
started with the basic installation of the Switch.
Chapter 3, Identifying External Components.
Describes the front panel, rear panel and LED
indicators of the Switch.
iv
Chapter 4, Connecting the Switch. Shows you how to
connect the Switch to your Ethernet network.
Appendix A, Technical Specifications. Lists the
technical (general, physical and environmental, and
performance) specifications of the Switch.
Appendix B, RJ-45 Pin Specification. Describes the
RJ-45 receptacle/connector and the straight and
crossover cable.
1
INTRODUCTION
This chapter describes the features of the Switch and
some background information about Ethernet/Fast
Ethernet switching technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing
complexity of desktop computing applications are
fueling the need for high performance networks. A
number of high-speed LAN technologies have been
proposed to provide greater bandwidth and improve
client/server response times. Among them, 100BASE-
TX (Fast Ethernet) provides a non-disruptive, smooth
evolution from the current 10BASE-T technology. The
non-disruptive and smooth evolution nature, and the
dominating potential market base, virtually guarantee
cost effective and high performance Fast Ethernet
solutions in the years to come.
100Mbps Fast Ethernet is a standard specified by the
IEEE 802.3 LAN committee. It is an extension of the
10Mbps Ethernet standard with the ability to
transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol.
2
Switching Technology
Another approach to pushing beyond the limits of
Ethernet technology is the development of switching
technology. A switch bridge Ethernet packets at the
MAC address level of the Ethernet protocol,
transmitting among connected Ethernet and/or Fast
Ethernet LAN segments.
Switching is a cost-effective way of increasing the total
network capacity available to users on a local area
network. A switch increases capacity and decreases
network loading by dividing a local area network into
different segments, which don’t compete with each
other for network transmission capacity.
The switch acts as a high-speed selective bridge
between the individual segments. The switch, without
interfering with any other segments, automatically
forwards traffic that needs to go from one segment to
another. By doing this, the total network capacity is
multiplied, while still maintaining the same network
cabling and adapter cards.
For Fast Ethernet networks, a switch is an effective
way of eliminating problems of chaining hubs beyond
the “two-repeater limit.” A switch can be used to split
parts of the network into different collision domains,
3
making it possible to expand your Fast Ethernet
network beyond the 100BASE-TX network’s 205-meter
network diameter limit. Switches support both
traditional 10Mbps Ethernet and 100Mbps Fast
Ethernet. They are also ideal for bridging between the
existing 10Mbps networks and the 100Mbps networks.
Switching LAN technology is a marked improvement
over the previous generation of network bridges,
which were characterized by higher latencies. Routers
have also been used to segment local area networks,
but the router costs more, is difficult to setup, and
maintenance intensive, all these make routers
relatively impractical. Today switches are an ideal
solution to most kinds of local area network congestion
problems.
Features
The Switch was designed for easy installation and
high performance in an environment where traffic on
the network and the number of user increases
continuously.
The Switch with their small, desktop size was
4
specifically designed for small to middle workgroups.
This Switch can be installed where space is limited;
moreover, they provide immediate access to a rapidly
growing network through a wide range of user-reliable
functions.
The Switch is ideal for deployment with multiple high-
speed servers for shared bandwidth 10Mbps or
100Mbps workgroups. With the 200Mbps high
bandwidth (100Mbps full-duplex mode), any port can
provide workstations with a congestion-free data pipe
to access the server/workstation.
The Switch is expandable by cascading two or more
switches together. As all ports support 200Mbps, the
Switch can be cascaded from any port and to any
number of switches.
The Switch is a perfect choice for site planning to
upgrade to Fast Ethernet in the future. Ethernet
workgroups can connect to the Switch now, and
change adapters and hubs anytime later without
changing the Switch or reconfigure the network for
migrating to Fast Ethernet.
The Switch combine dynamic memory allocation with
store-and-forward switching scheme to ensure that the
buffer is effectively allocated for each port, while
Autres manuels pour TE100-S16Eplus
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TRENDnet Changer
TRENDnet
TRENDnet TK-1603R Manuel utilisateur
TRENDnet
TRENDnet TEG-S28TX Manuel utilisateur
TRENDnet
TRENDnet TK-408K Manuel de la liste des pièces
TRENDnet
TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manuel utilisateur
TRENDnet
TRENDnet TK-803R Manuel utilisateur
TRENDnet
TRENDnet TE-910plus Manuel utilisateur
TRENDnet
TRENDnet TE100-S800i Manuel utilisateur
TRENDnet
TRENDnet TPE-T80H Manuel utilisateur
TRENDnet
TRENDnet TE100-DX16 Manuel utilisateur
TRENDnet
TRENDnet TO-PG541 Manuel utilisateur
TRENDnet
TRENDnet TK-200K Manuel
TRENDnet
TRENDnet TEG-S50G Manuel de l'opérateur
TRENDnet
TRENDnet TI-G102i Manuel utilisateur
TRENDnet
TRENDnet TK-207K - KVM Switch - USB Manuel utilisateur
TRENDnet
TRENDnet TEG-448WS - Switch Manuel utilisateur
TRENDnet
TRENDnet TK-207K - KVM Switch - USB Instructions de montage
TRENDnet
TRENDnet TU-400E Manuel utilisateur
TRENDnet
TRENDnet TPE-1020WS Manuel utilisateur
TRENDnet
TRENDnet TEG-30102WS Manuel utilisateur
TRENDnet
TRENDnet TE-800 Manuel utilisateur
