TRENDnet TE-16PNP Manuel utilisateur

TE-16PnP User's Guide

Oct. 1995

Trademarks

Brand and product names used in this guide are trademarks and/or registered trademarks of their

respective companies.

FCC Certification

• TE-16PnP FCC Class B ID : KA2APC20001

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables must be used in order to comply with emission limits.

Features

The TE-16PnP cards comply with IEEE 802.3 Ethernet standards and use VLSI components for

enhanced reliability. The following are a few of the cards’ distinctive features.

• Easy Installation: The cards have no physical jumpers or DIP switches. When installed in a

PnP computer, configuration is handled entirely by the system with no user intervention. In

non-PnP systems, configuration is accomplished through an innovative setup program

provided with the TE-16PnP package. In either case, assignment of system resources is

handled through software instead of physical jumpers. Once the card is inserted into a slot in

your computer, you don’t need to remove it to change its settings.

• Support for 8-bit and 16-bit expansion slots: The cards can be used in 8-bit (the sort XT-

style) or 16-bit (AT-style) expansion slots. The card automatically detects the type of slot

being used.

• Use of NE-2000 Drivers: The TE-16PnP cards can use the same network drivers as the

Novell NE-2000.

• Setup/Diagnostic program and LEDs: The TE-16PnP setup/diagnostic program tests all

card functions to verify correct operation of the card. The LEDs on the card report network

activity.

• Remote boot function: The cards can be used on PCs or diskless workstations for remote

booting on the network. To use the remote boot function, a remote boot ROM (purchased

separately) must be installed on the card.

• Runs a wide variety of networking software: The TE-16PnP cards can be used with all

popular networking software. A complete list of supported software can be found at the end

of this guide in the Specifications section.

Quick Installation Guide

Congratulations on your purchase of a TE-16PnP adapter. With this adapter, you are sure to get

the most for your investment -- as result of the rigorous quality-control programs implemented in

all our products. Again, congratulations and happy networking!

This guide applies to the following adapters:

Model Connector Media

TE-16PnP BNC, RJ-45 Thin coax, UTP

Adapter Installation

CAUTION: The adapter is packed in a plastic antistatic package to protect it during shipment.

To avoid damaging any static-sensitive components, after removal from the package, be sure to

reduce any static electricity on your body. You can touch the metal chassis of your computer,

and maintain grounding by wearing a wrist strap attached to the chassis.

1. Turn off your computer and then install the adapter into an empty 8 or 16 bit slot.

2. Connect the computer to a network.

3. On non-PnP systems, configure the card by running the card’s setup program,

TE16PNP.EXE. See Setup Program. After installing and configuring the card (for both non-

PnP and PnP systems), you can run the TE-16PnP setup program’s diagnostic functions to

test the reliability of the configuration.

4. Install the appropriate network software driver. See Supported Network Drivers.

Boot ROM Installation (Optional)

A Boot ROM allows your computer to load the operating system over the network. Among the

operating systems that can be loaded are Novell Netware, IBM LAN Server, and MS LAN

Manager.

1. Plug in the Boot ROM into the provided socket on the adapter.

2. Enable the Boot ROM function and select its starting address. See Setup Program.

Setup Program

This program comes in a diskette with the adapter package. To run, type the following at the

DOS prompt

> A:\UTILITY\TE16PNP

The main menu appears with the following options:

• Setup Configuration. Lets you specify the connector type, I/O base address, interrupt

number, boot ROM starting address, and whether or not to enable the remote boot function.

For a list of the various supported settings, see Specifications.

• Run Diagnostics. Lets you perform a diagnostic test on your adapter.

When configuring multiple adapters, ensure to assign a different I/O base address and interrupt

number for each. Also, reboot your computer after saving a new configuration to allow the new

configuration to be loaded into the system memory.

Note: If data in the EEPROM have been corrupted, setup would not be able to configure the

adapter. If this occurs, type the following at the DOS prompt

> A:\UTILITY\TE16PNP /I

This command restores the data in the EEPROM, thus allowing configuration of the adapter.

LED Indicators

The LED indicators help you monitor the network status. They are arranged in a row and are

located on the same side as the connectors(s). The following describes the function of each:

Power/Tx

Connector Used State Description

UTP/BNC ON There is power

Link/Rx

Connector Used State Description

UTP/BNC ON There is link

between port &

node

Supported Network Drivers

Before you could use an adapter in a certain networking environment, you need to install first its

driver program for that type of environment. Otherwise, the adapter will not operate properly.

• NetWare 2.x, 3.x, 4.x ODI driver (client and server)

• Windows NT / Windows NT Advanced Server

• Windows for Workgroups V.3.11

• Windows 95

• SCO Unix

• NDIS Driver

• Packet Driver

• NBIOS Driver

Aside from the drivers listed above, you may also use the NE2000 drivers on the TE-16PnP. For

the installation procedure, see the README file in the driver diskette.

Specifications

• Complies with IEEE 802.3 10Base-2 and 10Base-T Ethernet standards

• Compliant with Plug and Play ISA Specification Version 1.0a

• Card configured through software program (for non-PnP systems)

• Auto detection of 8-bit or 16-bit ISA bus

• Diagnostics program for error tracking on board level

• I/O address: 200h, 220h, 240h, 260h, 280h, 2A0h, 2C0h, 2E0h, 300h*, 320h, 340h, 360h,

380h, 3A0h, 3C0h, 3E0h

• IRQ: 3*, 4, 5, 9, 10, 11, 14, 15

• Boot ROM starting address: C0000h, C40000h, C8000h, CC000h, D0000h*, D4000h,

D8000h, DC000h

• Boot ROM size: 8k*, 16k

• Buffer RAM size: 16K bytes

• Transmission distance:

• UTP: 100 meters

• BNC: 185 meters (without repeater), 925 meters (with repeater)

• Addressable users: 1024

( *: default value)

Table des matières

Autres manuels TRENDnet Carte réseau

TRENDnet

TRENDnet TEW-647GA Manuel utilisateur

TRENDnet

TRENDnet TPA-311 Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITXRL Manuel utilisateur

TRENDnet

TRENDnet TE100-PCBUS Manuel utilisateur

TRENDnet

TRENDnet TEW-226PC Manuel utilisateur

TRENDnet

TRENDnet TE100-PCIA Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

TRENDnet

TRENDnet TEW-421PC Manuel utilisateur

TRENDnet

TRENDnet WN8020B Manuel utilisateur

TRENDnet

TRENDnet TEW-PC16 Manuel utilisateur

TRENDnet

TRENDnet TE100-PCIA Manuel utilisateur

TRENDnet

TRENDnet TEW-641PC Manuel utilisateur

TRENDnet

TRENDnet TEW-221PC Manuel utilisateur

TRENDnet

TRENDnet TPL-410APK Manuel utilisateur

TRENDnet

TRENDnet TEW-202CF Manuel utilisateur

TRENDnet

TRENDnet TE100-PCIWA Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITXR Manuel utilisateur

TRENDnet

TRENDnet TEM-336T Manuel utilisateur

TRENDnet

TRENDnet TEW-637AP - 300Mbps Wireless Easy-N-Upgrader Manuel utilisateur

TRENDnet

TRENDnet TPL-101U Manuel utilisateur

TRENDnet

TRENDnet TE100-S4PCI Manuel utilisateur

TRENDnet

TRENDnet TEW-601PC - SUPER G MIMO WRLS PC CARD Manuel utilisateur

TRENDnet

TRENDnet TEW-501PC Manuel utilisateur

TRENDnet

TRENDnet TEM-560T Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur

Gigafast

Gigafast EE101-AEX Manuel utilisateur

D-Link

D-Link DHP?P309AV Manuel utilisateur