Toshiba 1000 Series Manuel utilisateur

TOSHIBA/HOUSTON INVERTER PLANT

DESIGN DATA D-UM0029 Page 1 of 4

SUBJECT: 1000 Series UPS Options – Frequency Conversion

RELATED DATA FILE NO.

COPY DRAWN BY: DATE:

TO: H. Huynh 10/2005

TO: CHECKED BY:

TO: MTA 10/2005

TO: APPROVED BY: DATE:

NO. REVISION DATE BY TO:

FOR AUTHORIZED SERVICE PERSONAL ONLY

Models: 1000 Series UPS

CAUTIONS

INSTALLATION INSTRUCTIONS

Cautions:

Any maintenance, additions, and/or changes that are to be done to this UPS should be

performed by a certified Toshiba trained repair technician authorized to service

Toshiba’s 1000 Series UPS.

The followings are a list of minimum safety requirements that should be adhered to,

and is not to be interpreted to be the only safety requirements to follow. Please follow

all Local, State, and Federal Safety Requirements.

1) Verify that the UPS is off and that the power cord or main power is disconnected from

the power source. (Observe Lock-out/Tag-out procedures if applicable)

2) Remove watches, rings, and/or other metal objects.

3) Use insulated tools to prevent inadvertent shorts.

4) Wear safety glasses, rubber gloves and boots.

5) Do not lay tools or metal parts on top of the batteries.

6) All connections must be made in accordance with National and Local Electric Codes.

In no event will Toshiba Corporation be responsible or liable for either indirect or

consequential damage or injury that may result from the modification of this unit.

Installation Instructions:

TOSHIBA/HOUSTON INVERTER PLANT

DESIGN DATA D-UM0029 Page 2 of 4

SUBJECT: 1000 Series UPS Options - Frequency Conversion

NO. REVISION DATE BY

FOR AUTHORIZED SERVICE PERSONAL ONLY

Install “FlashH08” Flash Program

There are two types of installation files for the Flash program. The one that is appropriate

for you can be determined by first checking the “CPU Version” that is displayed on the

LCD display in the front panel.

1.) If the format is XX.X

This means that the CPU is an R mask type. In this case you should run the

“Flash3062_R” program to install the “FlashH08” flash software. Further instructions on

configuration are explained below.

2) If the format is XX.XB

This means that the CPU is a B mask type. In this case you should run the “Flash3062_B”

program to install the “FlashH08” flash software. Further instructions on configuration are

explained below.

Use “FlashH08 ” to flash R mask type/B mask type CPU

1. To properly configure and utilize this software, terminate all applications that

occupy COM 1. (COM 1 is the default communication port for this software)

2. Connect the RS232 cable to the UPS from “COM1” of the PC.

3. Turn off the UPS, but keep the AC Line on. The proper procedure for this is

explained in the UPS manual that is included with the UPS.

4. Click on the appropriate “FlashH08” software that was installed in the previous

section.

i. If you installed the R mask type, it should be labeled “R Mask Flash” in the

title like the one shown below.

TOSHIBA/HOUSTON INVERTER PLANT

DESIGN DATA D-UM0029 Page 3 of 4

SUBJECT: 1000 Series UPS Options - Frequency Conversion

NO. REVISION DATE BY

FOR AUTHORIZED SERVICE PERSONAL ONLY

ii. If you installed the B mask type, it should be labeled “B Mask Flash” in the

title like the one shown below.

5. Click Load in the Menu bar to load the file (*.mot) that you want to reflash to the

CPU.

6. Click the ALL button in the Toolbar and it will display “Programming.”1,2 During

this period, both the LEDs labeled “Bypass_LED” and “On_LED” are turned on

for the tower UPS. For the Rackmount 1U, both the LEDs labeled “Inverter” and

“DC LOW” are lit.

TOSHIBA/HOUSTON INVERTER PLANT

DESIGN DATA D-UM0029 Page 4 of 4

SUBJECT: 1000 Series UPS Options - Frequency Conversion

NO. REVISION DATE BY

FOR AUTHORIZED SERVICE PERSONAL ONLY

Setup:

1. Make sure the UPS is off and the AC Line is on. The LCD screen should appear

blank.

2. Press and hold the function button for 1 second and release the button to enter the

front panel settings. Once in this mode, you can scroll through different settings

using the function button.

3. Look for the newly added software, “Freq Convert Set” and press Enter.

4. Once inside, you can change the output frequency by pressing the function button.

5. After choosing the correct frequency, press Enter to select it. Once selected, the

LCD will display a blank screen.

6. Turn on the UPS.

Note:

1If the communication fails during “Programming” for:

•R Mask – user should wait more than 35 seconds and then click the “W” button on

the Toolbar to start “Programming” again.

•B Mask – The LED labeled Alarmed_LED will be turned on. The user should wait

more than 10 seconds and then click the “W” button on the Toolbar to start

“Programming” again.

2Do not run any other application software on the PC during “Flash Process”, because the

“FlashH08” application uses up a large amount of the PCs resources.

Autres manuels pour 1000 Series

Table des matières

Autres manuels Toshiba UPS

Toshiba

Toshiba 1500 Series Manuel utilisateur

Toshiba

Toshiba 1000 Series Manuel utilisateur

Toshiba

Toshiba 4200FA CT/XT Manuel utilisateur

Toshiba

Toshiba T90S3S08KS6XSN Manuel utilisateur

Toshiba

Toshiba 4200FA Series Manuel utilisateur

Toshiba

Toshiba T-Series T1000 Manuel utilisateur

Toshiba

Toshiba 4200FA Series Manuel utilisateur

Toshiba

Toshiba 4400 Series Manuel utilisateur

Toshiba

Toshiba UNINTERRUPTIBLE POWER SYSTEM 1600XP Manuel utilisateur

Toshiba

Toshiba G9000 SERIES Manuel utilisateur

Toshiba

Toshiba 1800 SERIES Manuel utilisateur

Toshiba

Toshiba 1400 XL PLUS Series Manuel utilisateur

Toshiba

Toshiba 4200FA XT Manuel utilisateur

Toshiba

Toshiba G9000 SERIES Manuel utilisateur

Toshiba

Toshiba G9000 SERIES Manuel utilisateur

Toshiba

Toshiba G9000 SERIES Manuel utilisateur

Toshiba

Toshiba RemotEye II Manuel utilisateur

Toshiba

Toshiba UC1A1A020C6TB Manuel d'installation

Toshiba

Toshiba T1000 Series Manuel utilisateur

Toshiba

Toshiba 1600XPi SERIES Manuel utilisateur

Toshiba

Toshiba 1600 Series Instructions d'installation

Toshiba

Toshiba 431A Manuel utilisateur

Toshiba

Toshiba 4200FA Series Manuel utilisateur

Toshiba

Toshiba 1600XP SERIES Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur