Toshiba Carrier TCB-AX21UL Manuel utilisateur

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)

Owner’s Manual

Remote controller for air

conditioner (Split type) 1

English

Manuel du proprietaire

Télécommande pour climatiseur

(Type split) 19

Français

Remote Controller

Model name:

Wireless remote controller kit

TCB-AX21UL

Generic model name Wireless remote controller

and signal receiving unit

TCB-AX21UL WX-TA01UES

(Wireless remote controller

model name)

Wireless remote controller

(WX-TA01UES)

Signal receiving

unit

+01EN.BOOK Page 1 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–1–

Contents

1 PRECAUTIONS FOR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 CORRECT USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 TIMER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 SLIDE SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 HOW TO INSERT THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . 12

7 HOW TO HANDLE THE REMOTE CONTROLLER . . . . . . . . . . . 13

8 HOW TO USE THE REMOTE CONTROLLER CORRECTLY . . . 14

9 ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

10 HOW TO PERFORM EMERGENCY OPERATION. . . . . . . . . . . . 16

11 BEFORE ASKING FOR REPAIR WORK . . . . . . . . . . . . . . . . . . . 17

Thank you very much for purchasing TOSHIBA/Carrier Remote Controller for Air

Conditioner.

Please read this owner's manual carefully before using your Remote Controller for Air

Conditioner.

• Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or

dealer).

Request to constructor or dealer

Please clearly explain the contents of the Owner’s manual and hand over it.

1-EN

+01EN.BOOK Page 1 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–2–

1PRECAUTIONS FOR SAFETY

WARNING

WARNINGS ABOUT INSTALLATION

• Make sure to ask the qualified installation professional

in electric work to install the remote controller.

If the remote controller is inappropriate installed by

yourself, it may cause, electric shock, fire, and so on.

• Make sure to install the air conditioner specified by

TOSHIBA/Carrier and ask the exclusive dealer when

installing. If the air conditioner is installed by yourself,

it may cause electric shock or fire, etc.

WARNINGS ABOUT OPERATION

• Prevent any liquid from falling into the remote

controller.

Do not spill juice, water or any kind of liquid.

It may cause malfunction, electric shock or fire, etc.

• When you are aware of any error with the air

conditioner (smells like something burning etc.),

immediately turn off the circuit breaker to stop the air

conditioner, and make contact with the dealer. If the air

conditioner is continuously operated with an error, it

may cause malfunction, electric shock, fire, and so on.

WARNINGS ABOUT MOVEMENT AND REPAIR

• Do not repair any unit by yourself.

• Whenever the air conditioner needs repair, make sure

to ask the dealer to do it. If it is repaired imperfectly, it

may cause electric shock or fire.

• When reinstalling the air conditioner, contact with the

dealer.

If the installation is insufficient, it may cause electric

shock or fire, etc.

2-EN

+01EN.BOOK Page 2 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–3–

CAUTION

CAUTIONS ABOUT INSTALLATION

•

Do not install the remote controller in a place where its

signals do not reach the indoor unit.

•

Do not install the remote controller in the place under the

direct sunlight and close to any heat source. It may

cause malfunction.

•

The fluorescent lamp with rapid start system or inverter

system may disturb the signal reception. For details,

contact with the dealer of the air conditioner you have

purchased.

CAUTIONS ABOUT OPERATION

•

Do not drop or apply strong shock to the air conditioner.

It may cause malfunction of the remote controller.

•

Use batteries that meet the specifications.

3-EN

+01EN.BOOK Page 3 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–4–

2PART NAMES AND FUNCTIONS

Remote Controller (WX-TA01UES)

• Max. 8 indoor units can be operated by a remote controller as a group. (See page 14)

• Illustration of LCD shown below is for explanation. It may differ from the actual LCD.

1Transmitting part

2Remote controller sensor

The peripheral temperature is sensed when

the sensor button is pushed to remote

controller side.

3LCD

The operation mode is displayed.

4ON/OFF button

Pushing this button starts, and pushing again

stops the unit.

5Mode button

Selects desired operation mode.

6Fan speed button

7Timer Set button

Use to setup the timer.

(See page 10)

8ACL button

This button is used after replacement of

battery or selection of slide switch.

(See page 11)

9Slide switch

(See page 11)

Battery compartment

(See page 12)

Cover

Slide the cover holding its both sides.

SET

ACL

SENSOR

SKN AHC

ADR

4-EN

+01EN.BOOK Page 4 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–5–

AUTO louver display differs

according to the installed unit.

No function

Setup temperature button

Adjusts the set point.

Set the desired set point by pushing or

Filter button

No function

Swing/Air direction button

No function

Address button

(See page 14)

Ventilation button

Use this when a ventilation fan or other unit,

purchased on the market, has been

connected.

Sensor button

This button is used when selecting the temp.

sensor at the remote controller side. At the

shipment from the factory, this button is set to

the temp. sensor at the indoor unit.

SET

ACL

SENSOR

SKN AHC

ADR

5-EN

+01EN.BOOK Page 5 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–6–

Signal Receiving Unit

• The signal receiving unit is attached to the indoor unit.

• Hereinafter, all remote controller button names are indicated with respective symbols

displayed on the remote controller.

Example: ON/OFF button →

1Temporary operation button

(See page 16)

2Signal receiving unit

The signal sent from the remote controller is

received.

3Display lamp

One of displays flashed while an error occurs.

When the display lamp flashes, refer to

“BEFORE ASKING FOR REPAIR WORK” in

17 page.

4lamp

This lamp illuminates when unit is on.

5lamp

This lamp illuminates while the timer is

reserved.

6lamp

• In heating operation this lamp illuminates in

the following cases;

The operation has started.

The temp. controller has worked.

The unit is under defrost operation.

• This lamp flashes while a trouble occurs.

7lamp

This lamp illuminates to reamind to clean the

air filter.

CAUTION

• If “pi, pi” sound is heard, the MODE lamp

of the display lamp goes on, and the

lamp and lamp flash alternately, the

operation is not performed with the

desired mode.

• Even if you push , or when

remote controller operation is disabled

by the central control or other means, “pi”

is heard 5 times and the button operation

is not accepted.

6-EN

+01EN.BOOK Page 6 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–7–

Display section

All indicators are shown in the right and the lower figures for the

explanation.

Only selected contents are display in actual operation.

1Transmitting indication

Displayed while operating the switches of the

remote controller.

2Mode display

The selected operation mode is displayed.

3Fan speed display

The selected fan speed is displayed.

4Ventilation display

This appears while the ventilation fan is

operating.

5Remote control sensor display

This appears when the remote control sensor

is used.

6Set up temperature display

The selected set point is displayed.

7Louver position display

8SWING display

Displayed during up/down movement of the

louver.

9Timer display

Timer mode display

When pushing the Timer SET button, the

display of the timer is selected in order of

[OFF] →repeat OFF timer

→[ON] →No display.

ADR

ACL

SENSOR

SET

ADR

Display

section

Operation

section

(AUTO)

(HIGH)

(MED.)

(LOW)

7-EN

+01EN.BOOK Page 7 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–8–

Operation section

Push each button to select a desired operation.

• The details of the operation needs to be set up once, afterward, the air conditioner can be

used by pushing button only.

1Mode button

Selects desired operation mode.

2Fan speed button

Selects a fan speed.

3Timer set button

Use to setup the timer. (See page 10)

4ACL button

Use this button after battery exchange.

5Setup Temperature button

Adjusts the set point.

Set the desired set point by pushing or .

6ON/OFF button

When the button is pushed, operation starts,

and it stops by pushing the button again.

When the operation stops, the operation lamp

and all displays disappear.

7Filter button

No function

OPTION :

Remote controller sensor

Usually the TEMP. sensor of the indoor unit

measured a temperature.

A temperature around the remote controller

can also be measured.

For details, contact the dealer from which

you have purchased the air conditioner.

8-EN

+01EN.BOOK Page 8 Thursday, October 8, 2009 4:05 PM

Wireless remote controller kit Owner’s Manual

–9–

3CORRECT USAGE

Cool/Heat AUTO , Heat ,

Dry , Cool , Fan

Power supply

Turn on the power supply switch 12 hours

before starting the operation.

• After the power supply has been turned

on, the operation of the remote controller

is not accepted for approx. 1 minute. It is

not a failure.

(The sensor receives the signal once, but

the received contents are cleared.)

1Push (ON/OFF button).

2Push (Mode button)

operation to select one of ,,,,

and .

3Push (Fan Speed button) to select

one of fan speed modes.

When selecting , the fan speed is

automatically changed.

(During FAN mode, the air speed is not

automatically changed.)

4Push either or to select the

desired temperature.

During FAN mode, the temperature cannot be

set up.

5Stop

Push ON/OFF button.

When using the remote controller to stop the

unit, the outdoor unit fan may keep operating

for a while even if the compressor of the

outdoor unit has stopped.

•In heating operation, if the room is not

comfortably heated with FAN ,

select FAN or .

Although they are displayed, the function

may not be provided according to the used

indoor unit. (Fan speed is constant.)

•When the unit cannot be stopped by

the normal operation

Turn off the circuit breaker, and then

contact the shop which you purchased the

unit.

Automatic cool/heat

When all indoor units in the identical

refrigerant system are controlled as a group,

the cooling/heating operation is

automatically performed with the difference

between the setup temperature and the

room temperature.

Dry operation

• There is no dry function according to the

used indoor unit even if DRY is displayed

on the display section of the remote

controller. (Same to Cooling operation)

• When the room temperature approaches

the setup temperature, running/stop

operations are automatically repeated.

• In order not to return humidity to the room

as possible, the mode of indoor fan enters

LOW mode when the operation has

stopped.

• The fan speed cannot be adjusted

according to the used indoor unit or status

of the room temperature.

• The DRY mode cannot be used according

to the used indoor unit when the outdoor

temperature is 59°F (15°C) or lower.

9-EN

+01EN.BOOK Page 9 Thursday, October 8, 2009 4:05 PM

Autres manuels pour Carrier TCB-AX21UL

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toshiba Télécommande

Toshiba

Toshiba RBC-AX33UYP-E Manuel utilisateur

Toshiba

Toshiba VCR remote Manuel du propriétaire

Toshiba

Toshiba CAMILEO H30 Instructions d'installation et d'utilisation

Toshiba

Toshiba Lite-Vision plus RBC-AMS51E Manuel utilisateur

Toshiba

Toshiba RBC-AMS51E-EN Manuel utilisateur

Toshiba

Toshiba RBC-ASC11E Manuel utilisateur

Toshiba

Toshiba RB-RWS21-E Manuel utilisateur

Toshiba

Toshiba RBC-ASCU11-E Manuel utilisateur

Toshiba

Toshiba RBC-AS21E Manuel utilisateur

Toshiba

Toshiba RBC-AMS55E-EN Manuel utilisateur

Toshiba

Toshiba RBC-AX22CE2 Manuel utilisateur

Toshiba

Toshiba RBC-AMT32E Manuel utilisateur

Toshiba

Toshiba RG57A8/BGEF Manuel utilisateur

Toshiba

Toshiba TCB-SC642TLE2 Manuel utilisateur

Toshiba

Toshiba RBC-AX31U(W)-UL Manuel utilisateur

Toshiba

Toshiba OIS40R Manuel utilisateur

Toshiba

Toshiba RBC-AMT31-E Manuel utilisateur

Toshiba

Toshiba RBC-AS41E Manuel utilisateur

Toshiba

Toshiba Regza 32WLT68 Manuel utilisateur

Toshiba

Toshiba RBC-ASCU11-UL Manuel utilisateur

Toshiba

Toshiba Carrier RBC-AMS41UL Manuel utilisateur

Toshiba

Toshiba ASD-MTG-KITQ9 Manuel d'utilisation et d'entretien

Toshiba

Toshiba CT-8002 Manuel utilisateur

Toshiba

Toshiba RBC-IR2-PE Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation