Toshiba B-EP4DL Series Manuel utilisateur

PRINTED IN JAPAN

TOSHIBA Potable Printer

B-EP4DL SERIES

Document No. EO18-33023

Original Sep., 2008

(Revised )

Maintenance Manual

WARNING!

Follow all manual instructions. Failure to do so could create safety hazards such as fire or

electrocution.

NOTE:

Failure to follow manual instructions or any unauthorized modification, substitution orchange to

this product will void the limited product warranty.

EO18-33023

(Revision Date: Dec. 16, 2008)

CAUTION!

1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA

TEC.

2. The contents of this manual may be changed without notification.

by TOSHIBA TEC CORPORATION

ll Rights Reserved

570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

TABLE OF CONTENTS

Page

1. UNPACKING .............................................................................................................. 1- 1

1.1 Procedure ........................................................................................................................1- 1

1.2 Checks.............................................................................................................................1- 1

2. MAJOR UNIT REPLACEMENT.................................................................................. 2- 1

2.1 Replacing the CPU PC Board .........................................................................................2- 1

2.2 Replacing the LCD Unit ...................................................................................................2- 8

2.3 Replacing the Peel-off Roller...........................................................................................2- 9

2.4 Replacing the Peel-off Sensor.......................................................................................2- 10

2.5 Replacing the Drive PC Board.......................................................................................2- 12

2.6 Replacing the Battery Terminal .....................................................................................2- 13

2.7 Replacing the Stepping Motor .......................................................................................2- 14

2.8 Replacing the Print Head...............................................................................................2- 15

2.9 Replacing the Cover Open Switch and Media Sensor (Lower) .....................................2- 17

2.10 Replacing the Media Sensor (Upper) ............................................................................2- 19

2.11 Replacing the Platen Ass’y............................................................................................2- 21

3. TROUBLESHOOTING................................................................................................ 3- 1

1. UNPACKING EO18-33023

1.1 Procedure

1- 1

1. UNPACKING

1.1 Procedure

1) Open the carton.

2) Unpack the accessories from the carton.

3) Unpack the printer.

NOTE: Keep the carton and pad for future transportation of the printer.

1.2 Checks

1) Check for damage or scratches on the machine.

2) Confirm that none of the accessories are missing.

2. MAJOR UNIT REPLACEMENT EO18-33023

2.1 Replacing the CPU PC Board

2-1

2. MAJOR UNIT REPLACEMENT

WARNING!

1. Disconnect the power cord before installing the main parts.

2. Be careful not to injure your fingers when replacing the main parts.

CAUTION!

1. Since a lot of small moulded parts are used in this printer, care must be taken not to damage or lose

them.

2. Be careful not to damage the print head while removing and reassembling.

3. In the United States, used lithium ion batteries should be returned to the store where you bought the

machine. (USA only)

4. LITHIUM ION BATTERYDISPOSE OF PROPERLY

Caution: Do not handle damaged or leaking lithium ion battery.

5. Before handling the main parts, be sure to discharge static electricity in human body through other

metals. Failure to do this may damage the CPU PC board, print head, etc..

NOTES:

1. Before replacing the main parts, print out the maintenance counter values and the parameter values and keep

the printout. (Refer to Section 4.2 Diagnostics Test in the System Mode Manual.)

After replacing, restore the setting according to the printout.

2. Use precision screwdrivers for replacing the precision components which are installed into the printer.

2.1 Replacing the CPU PC Board

1) Turn off the printer.

2) Slide the Battery Lever in the direction of the arrow, and remove the Battery Pack from the printer.

3) Remove the four Tapping Screws from the Bottom Cover.

Battery Lever

Battery Pack

T-3x10 Screw

2. MAJOR UNIT REPLACEMENT EO18-33023

2.1 Replacing the CPU PC Board

2-2

4) Press the Top Cover Open Button to open the Top Cover.

5) Remove the Left Side Cover in the direction of the arrow.

6) Remove the Right Side Cover and the Front Cover in the direction of the arrow, respectively.

NOTE: The Gears shown in the picture below are not secured and are easily removed. Be carefu

not to drop and break or lose them.

Top Cover

Top Cover Open Button

Left Side Cover

Gea

Right Side Cover

Front Cove

2. MAJOR UNIT REPLACEMENT EO18-33023

2.1 Replacing the CPU PC Board

2-3

7) Remove the Front Cover.

6) Disconnect all Connectors and FPC Cable from the CPU PC Board.

NOTE: Before disconnecting the FPC Cable, release the Connector Lock.

7) Disconnect the Earth Terminal from the Drive PC Board.

Front Cover

CPU PC Board

FPC Cable

Connector Lock

CPU PC Board

Drive PC Board

Earth Terminal

2. MAJOR UNIT REPLACEMENT EO18-33023

2.1 Replacing the CPU PC Board

2-4

8) Open the Hooks, then remove the CPU PC Board from the Front Cover.

9) Remove the screw, then remove the Earth Terminal.

10) Replace the CPU PC Board with a new one, then reassemble in the reverse order of removal.

Hook

CPU PC Board

T-2x5 Screw

Earth Terminal

2. MAJOR UNIT REPLACEMENT EO18-33023

2.1 Replacing the CPU PC Board

2-5

11) Close the front cover.

12) Mount the left side cover to the printer while fitting the tabs on the left side cover into the slots of the printer

enclosure.

Fit the tabs A to D into the slots A’ to D’.

Front Cover

Tab Tab B Tab C Tab D

’

B’

C’

D’

NOTES:

1. Make sure that the pins on the both sides of the front cover are fit in position, as shown in the

pictures below.

2. Do not reassemble the Front Cover while the Top Cover Open Button is pressed. Doing so may

cause the Top Cover not to open.

Top Cover Open Button

Good No Good

2. MAJOR UNIT REPLACEMENT EO18-33023

(Revision Date: Dec. 16, 2008)

2.1 Replacing the CPU PC Board

2-6

13) Mount the right side cover to the printer while fitting the tabs on the right side cover into the slots of the

printer enclosure.

Fit the tabs A to C into the slots A’ to C’.

NOTE:

It is easy to mount the left side cover if you fit the tabs from the LCD side in order, then secure the bottom

side. Be careful not to catch the cable by the cover while reassembling.

Tab

Tab BTab C

’

B’

C’

NOTE:

It is easy to mount the right side cover if you fit the tabs from the LCD side in order, then secure the

bottom side. Be careful not to catch the cable by the cover while reassembling.

Right Side Cover

Left Side Cove

Table des matières

Autres manuels Toshiba Imprimante

Toshiba

Toshiba e-STUDIO222CP Manuel utilisateur

Toshiba

Toshiba B-852 Advance Manuel utilisateur

Toshiba

Toshiba SureMark 4610 Manuel utilisateur

Toshiba

Toshiba B-672-QP Manuel utilisateur

Toshiba

Toshiba 1NR Manuel utilisateur

Toshiba

Toshiba B-FP3D-GH52-QM-R Manuel utilisateur

Toshiba

Toshiba B-SX6T Series Manuel utilisateur

Toshiba

Toshiba B-SX6T Series Guide de l'utilisateur

Toshiba

Toshiba B-EX4 SERIES Caractéristiques techniques

Toshiba

Toshiba B-670-QQ Manuel utilisateur

Toshiba

Toshiba E-STUDIO2323AM Manuel utilisateur

Toshiba

Toshiba E-studio18 Instructions originales

Toshiba

Toshiba B-EP2DL Series Guide de l'utilisateur

Toshiba

Toshiba B-EP2DL Series Manuel utilisateur

Toshiba

Toshiba B-EX4 T1 Series Manuel

Toshiba

Toshiba B-EP2DL Series Manuel utilisateur

Toshiba

Toshiba e-STUDIO810 GA-1140 Manuel utilisateur

Toshiba

Toshiba e-STUDIO350 Manuel utilisateur

Toshiba

Toshiba TRST-A10 SERIES Manuel utilisateur

Toshiba

Toshiba B-SA4TP SERIES Manuel utilisateur

Toshiba

Toshiba E-STUDIO E-Studio 3511 Manuel de service

Toshiba

Toshiba GA-1120 Guide de configuration

Toshiba

Toshiba e-STUDIO 723 Manuel utilisateur

Toshiba

Toshiba TRST-A15 SERIES Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur