Toshiba TEC B-SP2D Series Manuel utilisateur
TOSHIBA TEC Portable Printer
B-SP2D Series
Wireless LAN Setting Tool Operating Specification
First Edition: February 12, 2004
For customers
i
TABLE OF CONTENTS
Page
1. SCOPE............................................................................................................................................................1
2. GENERAL DESCRIPTION..............................................................................................................................1
3. REQUIRED SYSTEM CONFIGURATION.......................................................................................................1
4. SOFTWRE INSTALLATION ...........................................................................................................................2
5. OPERATING PROCEDURE (WHEN USING ACT-IR220Lplus) ....................................................................3
6. OPERATING PROCEDURE (WHEN USING IrDA I/F SUPPORING IrCOMM)............................................11
- 1 -
1. SCOPE
This specification applies to the operating specification of the B-SP2D RFLAN Configuration Tool that is
used to set the ireless LAN parameters for the B-SP2D-GH40 portable printer ireless LAN interface
model.
2. GENERAL DESCRIPTION
There are t o ays to set the ireless LAN parameters: the ay the B-SP2D RFLAN Configuration Tool
is used and the ay the eb bro ser is used.
When using the B-SP2D RFLAN Configuration Tool, the ireless LAN parameters are set via IrDA
interface.
When using the eb bro ser, the parameters are set on the eb bro ser and transferred to the printer
via ireless LAN interface.
Regarding the detailed information about these methods, refer to the B-SP2D Series Wireless LAN
Net ork Specification.
The parameter settings are stored in the nonvolatile memory of the ireless LAN module installed in the
printer.
3. REQURIED SYSTEM CONFIGURATION
System: DOS/V computer running Windo s® 95, Windo s® 98, Windo s® 2000, or
Windo s® XP
Operations are not guaranteed ith other OS.
Interface: Interface bet een the PC and the printer is IrDA interface.
When using TEC Protocol, Actisys ACT-IR220Lplus should be used.
When using IrCOMM, the IrDA interface supporting IrCOMM should be used.
Memory capacity: Minimum 16MB (32MB or more recommended)
Available hard disk space: 10MB or more
NOTE: Windo s is a registered trademark of Microsoft Corporation in the United States and other countries.
- 2 -
4. SOFTWARE INSTALLATION
[SETUP DISK]
The setup disk of the B-SP2D RFLAN Configuration Tool consists of 3 floppy disks.
[Inst ll tion Procedure]
1. Start Windo s 95, Windo s 98, Windo s 2000, or Windo s XP, and insert Setup Disk (1/3) into the
PC floppy drive.
2. Click on the START button then highlight RUN and click on RUN.
3. When the RUN display appears, type in A:\SETUP.EXE, and click on the OK button.
4. Install the RFLAN Configuration Tool by follo ing the messages displayed on the screen.
5. After the RFLAN Configuration Tool has been installed, the completion screen ill automatically
appear. This is the end of the RFLAN Configuration Tool installation.
B-SP2D RFLAN
Configur tion Tool
WR.FD-SP2D-RFLAN-PARATOOL
7FM00557000
31st October 2003
V001.000
Copyright © 2003
TOSHIBA TEC CORPORATION
All Rights Reserved
DISK(1/3)
- 3 -
5. OPERATING PROCEDURE (WHEN USING ACT-IR220Lplus)
When using the ACT-IR220Lplus hich is a jig connected to the serial port, TEC Protocol should be
used.
(1) Confirming the IrDA Setting of the Printer
Turn on the printer hile pressing and holding the FEED button (until the status indicator blinks in
green) to start the printer in the system mode. The printer ill automatically print the self
diagnostic test result. Confirm that IrDA TEC 19200 is printed on it.
If not, refer to the System Mode Section in the B-SP2D Series External Equipment Interface
Specification, and change the setting.
(2) Starting the Printer in the System Mode
Start the printer in the system mode in the above-mentioned procedure, and the printer ill
automatically print the self diagnostic test result.
After the self diagnostic test label is printed, do not press the FEED button. Doing this causes
the printer to print the slant line pattern and enter the mode here the parameter setting cannot be
performed.
- 4 -
(3) Starting the Application
Start the RFLAN Configuration Tool.
- 5 -
(4) Starting the Parameter Setting Mode
First, confirm that IrDA: TEC Protocol is selected for the Control of the Com Settings, and the
IrDA port to hich the ACT-IR220Lplus is connected is selected for the PORT.
Then, face the ACT-IR220Lplus to ard the IrDA interface indo of the printer, and click on the
Start button to cause the printer to enter the do nload mode.
When the do nloading succeeds, the status indicator on the printer ill blink in green.
The B-SP2D RF-LAN Configuration screen ill be sho n ith the Start button and the Com
Settings grayed out.
- 6 -
(5) Calling the Factory Set Initial Settings
When the Restore button is clicked on, the ireless LAN modules parameter settings ill turn to
the initial settings. At this time, the IP address ill al ays become 172.16.0.10. The factory
set IP address, ho ever, is comprised of the upper 2 bytes fixed to 172.16 and the lo er 2-byte
number that is equal to the printer ID.
- 7 -
(6) Loading the Parameter Settings
Clicking on the GetPara button enables loading the current ireless LAN modules parameter
settings.
- 8 -
(7) Parameter Setting
Clicking on the Send Para button enables storing the parameter settings in the ireless LAN
module. When the Send Para button is clicked on, the parameter settings starts to be
transmitted one by one. The item being transmitted is sho n belo the Send Para button.
Table des matières
Autres manuels Toshiba Imprimante
Toshiba
Toshiba B-SA4TM SERIES Manuel utilisateur
Toshiba
Toshiba e-STUDIO 207L Manuel utilisateur
Toshiba
Toshiba B-EP2DL Series Manuel utilisateur
Toshiba
Toshiba TEC B-850 Series Manuel utilisateur
Toshiba
Toshiba MR-2018 Manuel utilisateur
Toshiba
Toshiba SureMark 4610-SJ6 Manuel utilisateur
Toshiba
Toshiba B-SA4T Caractéristiques techniques
Toshiba
Toshiba B-852 Series Manuel utilisateur
Toshiba
Toshiba e-STUDIO350 Manuel utilisateur
Toshiba
Toshiba E-studio18 Instructions originales
Toshiba
Toshiba TEC B 452 Manuel de la liste des pièces
Toshiba
Toshiba GA-1310 Manuel utilisateur
Toshiba
Toshiba E-STUDIO2323AM Manuel utilisateur
Toshiba
Toshiba B-EP2DL Series Guide de l'utilisateur
Toshiba
Toshiba 1TN Manuel utilisateur
Toshiba
Toshiba GA-1120 Manuel utilisateur
Toshiba
Toshiba e-STUDIO810 GA-1140 Manuel utilisateur
Toshiba
Toshiba B-670-QQ Manuel utilisateur
Toshiba
Toshiba es525p Manuel utilisateur
Toshiba
Toshiba e-Studio 383P Manuel utilisateur
