TMG ST2030 Manuel utilisateur
W W W . T M G I N D U S T R I A L . C O M P 1/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Main Specifications :
- Overall assembled size : W6 x L9 x H3.65 (m) / 20 x 30 x 12 (ft)
- Shoulder height : 2 (m) / 6.6 (ft)
- Front roll up door : 3 x 3 (m) / W10 x H10 (ft)
Prior to assembly
Please read the instructions carefully before installation. It is important to follow your local
safety regulations and industry standards during installation. Regulations may include but are
not limited to :
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number,
please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not make any
alterations to the structure. Do not hang any weights on the frame during installation,
including parts. We are not responsible for any damages or injuries caused by inappropriate
installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and where it
touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all parts are
included prior to setup.
Installation steps
Step 1 : Review the whole structure and choose the proper installation site
Choose a solid flat level ground area to set up the building. Do not install the building on soft
ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that are not rated to
hold its weight.
We strongly recommend that you build the structure on a solid foundation such as cement and
use anchor bolts on all baseplates.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open
flames or exposed electrical wires. Do not keep heat sources near the fabric cover. Keep
W W W . T M G I N D U S T R I A L . C O M P 2/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
the building surroundings clear at all times
TMG-ST2030 Part List
Parts
code
Graphical
Description
Qty
BOX
1
Peak arch tube
7
1/1
2
Upper rafter tube
(middle truss)
10
1/1
2A
Upper rafter tube
(front truss)
2
1/1
2B
Upper rafter tube
(rear truss)
2
1/1
3
Shoulder tube
(middle truss)
10
1/1
3A
Shoulder tube
(front and rear truss)
4
1/1
4
Sidewall tube
14
1/1
5
Roof purlin
(horizontal tube)
54
1/1
5L
Left corner baseplate
(front and rear truss)
2
1/1
5R
Right corner baseplate
(front and rear truss)
2
1/1
W W W . T M G I N D U S T R I A L . C O M P 3/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
6
Door column baseplate
(front truss)
2
1/1
6A
Middle column baseplate
(rear truss)
3
1/1
7
Middle truss baseplate
10
1/1
7A
Ratchet
14
1/1
8
Door frame lower tube
(front and rear truss)
5
1/1
9
Door frame upper tube
(front and rear truss)
4
1/1
9A
Rear frame middle tube
1
1/1
10
Door frame horizontal tube
(front and rear truss)
4
1/1
10A
Door frame horizontal
tube (rear truss)
2
1/1
11
Ceiling cross bar
6
1/1
11A
Two wheel rope pulley
(pre-installed on 2A)
1
1/1
11B
One wheel rope pulley
(pre-installed on 2A)
1
1/1
W W W . T M G I N D U S T R I A L . C O M P 4/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
12
Bottom tension bar
(front and rear cover)
4
1/1
12A
Bottom tension bar
(rear cover)
2
1/1
13
Diagonal bracing bar
(1st and last span)
4
1/1
13A
Tube clamp
8
1/1
14
Top cover tension tube
(for both bottom sides)
2
groups
1/1
15
Door dropping tube
1
groups
1/1
16
Expansion bolt M12x100mm (not
included)
52
1/1
17
Half round head bolt M10x80mm
63
1/1
18
Hex Bolt
M10x70mm
126
1/1
18A
Hex Bolt
M8x80mm
6
1/1
19
Hex Bolt
M10x30mm
20
1/1
19A
Hex Bolt
M10x50mm
8
1/1
W W W . T M G I N D U S T R I A L . C O M P 6/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Mark the ground in the final building location with a line showing the positions of base
plates, front, and rear doors. All lines should be drawn from center to center of all
baseplate tubes. Diagonal line X must be equal to Y.
Baseplates: all baseplates must be installed firmly with expansion bolts (#16) on this
step (Picture 1).
Parts used in this step :
-
(4) Baseplates (#5L,#5R)
-
(10) Baseplates (#7)
-
(2) Baseplates (#6)
-
(52) Expansion bolts M16 (#16)
-
(3) Baseplates (6A)
Picture 1
Step 2 : Assemble all trusses
The building includes 7 trusses : (1) front truss, (1) rear truss, and (5) middle
trusses. The front and the rear truss are to install with the fabric panel (#23 and
#23A).
Parts used to install the front truss in this step (refer to Picture 2) :
-
(1) Peak arch tube (#1)
-
(2) Upper rafter tube (#2A)
-
(2) Shoulder tube (#3A)
W W W . T M G I N D U S T R I A L . C O M P 7/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
-
(2) Sidewall tube (#4)
-
(1) Ceiling cross bar (#11)
-
(2) Hex bolt (#19)
-
(12) Hex bolt (#18)
-
(1) Two wheel rope pulley (#11A)
-
(1) One wheel rope pulley (#11B)
Picture 2
Parts used to install the rear truss in this step (refer to Picture 3) :
-
(1) Peak arch tube (#1)
-
(2) Upper rafter tube (#2B)
-
(2) Shoulder tube (#3A)
-
(2) Sidewall tube (#4)
-
(12) Hex bolt (#18)
W W W . T M G I N D U S T R I A L . C O M P 8/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Picture 3
Parts used to install (5) middle trusses in this step (refer to Picture 4).
-
(1x5) Peak arch tube (#1)
-
(2x5) Upper rafter tube (#2)
-
(2x5) Shoulder tube (#3)
-
(2x5) Sidewall tube (#4)
-
(1x5) Ceiling cross bar (#11)
-
(2x5) Hex bolt (#19)
-
(12x5) Hex bolt (#18)
Picture 4
•
Lay down all (7) trusses on the ground as picture 5 when the assembly is all
completed and before moving to next step.
Picture 5
W W W . T M G I N D U S T R I A L . C O M P 9/ 1 6 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Step 3 : Put up the front (1st) truss
•
Use of a crane or forklift is recommended, otherwise a team can use ropes to lift
the trusses, but you have to make sure it is safe, and have enough manpower. We
recommend 3 to 5 people to pull the truss up from different directions. When the
truss is up, tie the ropes to the heavy objects to make sure the truss will stay
upright and use bolt (#18) to connect the truss to the baseplate on both sides
(Picture 6).
•
Parts used in this step : (4) Half round head bolt (#18)
Picture 6
Step 4 : Put up the rest trusses
•
Refer to step 3 to put up the rest trusses, connect all purlins (#5) with bolt (#17)
and secure all bolts firmly on each span before going to next truss (Picture 7).
Table des matières
Autres manuels TMG Abri
TMG
TMG TMG-DT3041-PRO Manuel utilisateur
TMG
TMG TMG-MSC1220F Manuel utilisateur
TMG
TMG TMG-CP1220F Manuel utilisateur
TMG
TMG TMG-DT50FW8 Manuel utilisateur
TMG
TMG TMG-DT4041CG Manuel utilisateur
TMG
TMG DUAL TRUSS PRO Series Manuel utilisateur
TMG
TMG TMG-ST3060V-1.0 Manuel utilisateur
TMG
TMG TMG-MSC2030 Manuel utilisateur
TMG
TMG TMG-ST2041V Manuel utilisateur
TMG
TMG TMG-ST3040C Manuel utilisateur
TMG
TMG TMG-ST3070V-2.0 Manuel utilisateur
TMG
TMG TMG-MSC2030F Manuel utilisateur
TMG
TMG TMG-MSC1220 Manuel utilisateur
TMG
TMG TMG-DT3063-PRO Manuel utilisateur
TMG
TMG 3040 Manuel utilisateur
TMG
TMG TMG-CP2000-RD110 Manuel utilisateur
TMG
TMG TMG-DT5040CG Manuel utilisateur
TMG
TMG TMG-DT3380 Manuel utilisateur
TMG
TMG TMG-ST4081E Manuel utilisateur
TMG
TMG TMG-DT3061 Manuel utilisateur
Manuels Abri populaires d'autres marques
Shelters4Less
Shelters4Less SR1551 Manuel utilisateur
Vikre Handel AS
Vikre Handel AS JIT-1216 Manuel utilisateur
VARNA buildings
VARNA buildings C2020H Manuel utilisateur
Storage Canopy
Storage Canopy C3340R Manuel utilisateur
Frabill
Frabill ICE HUNTER 195 Manuel utilisateur
Shelters4Less
Shelters4Less SR1588 Manuel utilisateur
