TMG 3040 Manuel utilisateur

Page 1of 8

Main Specifications :

Overall assembled size : W9.15 x L12 x H2.2 (m) / 30 x 40 x 7.2(ft)

Ridge Peak Height : 2 m / 6.5ft + container height

Prior to assembly

Please read the instructions carefully before installation. It is very important to

follow your local safety regulations and industry standards during installation.

Regulations may include but are not limited to:

Safety helmets, protective eyewear, and clothing

Safety harnesses for all elevated workers

Proper ladder, cage, and safety operation

Check all components and parts before installation. All parts are marked with a part

number, please refer to the parts list to make sure you have all parts.

Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not

make any alterations to the structure. Do not hang any weights on the frame during

installation, including parts. We are not responsible for any damages or injuries caused by

inappropriate installation, unauthorized modifications or extreme weather.

This building is not intended for human occupancy.

It is recommended to tape or add foam/rubber on the frame where joints connect and

where it touches the cover. This will help extend the life span of the cover.

Read the following item list carefully and count the number of items to ensure that all

parts are included prior to setup.

Installation steps

Step 1 : Review the whole structure and choose the proper installation site

Choose a solid flat level ground area to set up the building. Do not install the building on

soft ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that are not

rated to hold its weight.

We strongly recommend that you put the containers on hard foundations before installing

the shelter.

Page 2of 8

Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames

or exposed electrical wires. Do not keep heat sources near the fabric cover. Keep the

building surroundings clear at all times.

TMG-ST3040C Part List

No.

Picture

Description

Quantity

BOX

Peak arch tube

1/1

Middle rafter tube

1/1

Shoulder tube

1/1

Purlin tube

1/1

Diagonal bracing bar

(1st and last span)

1/1

Baseplate Leftside

1/1

L2-7L

Baseplate Leftside

1/1

Baseplate Leftside

1/1

Baseplate Rightside

1/1

R2-R7

Baseplate Rightside

1/1

Baseplate Rightside

1/1

Double "L" shapeplate

1/1

Single "L" shapeplate

1/1

Water plug

1/1

Bolt M10*80

1/1

Page 3of 8

Bolt M8*70

108

1/1

Hex bolt

M8x80mm

1/1

Hex bolt

M10x30mm

1/1

Top cover

1/1

Braided rope

1/1

Step 2 : Place the containers making sure they are parallel and the correct width apart.

Make sure there is a gap of about 1 meter around the building. (refer to Picture 1 as

below)

Picture 1

Page 4of 8

Step 3 : Assemble base tubes

1. Ensure the site is level and firm. place the containers 8980mm apart

2. Secure base plate and “L” shape plate (#6、#7) to the container top. Bolt in M8*80

(#11) connect evenly adjoining spigots at each side (L1-L8; R1-R8)

3. Please reserve 5cm space for wedding of the “L” shape plate.

4. Weld the base plate and “L” shape plate (#6、#7) to the container top (refer to Picture

2 as below)

Components are :

(1) Base plate (#L1)

(6) Base plate (#L2-#L7)

(1) Base plate #(L8)

(1) Base plate (#R1)

(6) Base plate (#R2-#R7)

(1) Base plate (#R8)

(32) Hex bolt M8x80mm (#11)

(28) Double "L" shape plate (#6)

(8) Double "L" shape plate (#7)

Picture 2

Page 5of 8

Step 4 : Connect all trusses

Layout all truss components on the ground in the correct configuration before bolting

them together.

There are total 9 trusses to build, use the hex bolt (#10) to connect all tubes

together. Then use (#12) bolts to link (#5) to (#2) . (refer to Picture 3 as below)

Components are :

(1x9) Peak arch tube (#1)

(2x9) Middle rafter tube (#2)

(2x9) Shoulder tube (#3)

(1x9) Ceiling cross bar (#5)

(8x9) Bolt M8*70 (#10)

(2x9) (18) Hex bolt M10x30mm (#12)

Picture 3

Step 5 : Put up all trusses

Install each truss on the base tube. Use hex bolt (#10) to secure the truss to the base

tube firmly. We recommend to use a crane or forklift to lift the truss and have 2 to

3 people on site to work together. Please make sure it is safe and secure when

installation is proceeding. (refer to picture 5 as below)

Page 6of 8

Picture 4

Install purl in tubes (#4) and use locking bolts (#9). Add the water plugs on both ends of

the base tubes. (refer to picture 6 as below)

Components are :

•(40) Purl in tube (#4)

•(45) Locking bolt (#9)

•(4) Water plug (#8)

Picture 5

Page 7of 8

Overall structural inspection : check all components and trusses to ensure the entire

structure is rectangular as specified in ( picture 1). All trusses must be 90 degrees straight

up from the container.

Secure and tighten all bolts and nuts on this step. But do not over tie! Otherwise you

might damage the tubes or components.

Step 6 : Install the cover

Expand the fabric cover (#13) on the ground, pull it carefully from one side into

place, stay away from snagging on sharp edges, bolts, etc. Use the braided rope (#14)

to tie both sides to the bottom tube rebar through the grommets. Also pull the front

and rear cover and tie to the trusses. All four sides need to be tied firmly at the same

time to make sure it is square, smooth and straight. All grommet needs to be

fastened to the frame with wavy lines. Finally tie the corners of the cover to the

corners of the frame. (refer to picture 6 & 7 as below)

Picture 6

Page 8of 8

Picture 7

After Installation

Walk around and inspect the building periodically to make sure the parts are firmly

fixed and the whole building is well supported. Check all bolts and hardware

connectors to make sure they are in place and tightened. Check the base plates,

adjust the ropes if necessary and clean the cover regularly.

Snow accumulating on the fabric cover must be removed as soon as possible. If

snow is allowed to become solid ice on the cover, it could increase the weight on the

roof and collapse the buildingor reduce the life span.

We strongly recommend you remove any snow from the roof immediately. Do not leave

any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all times. Do

not allow snow to accumulate and pile up on the sides of the building. Otherwise the

pressure from the sides will push inwards and could lead to a collapse.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TMG Abri

TMG

TMG TMG-ST4081V Manuel utilisateur

TMG

TMG DUAL TRUSS PRO Series Manuel utilisateur

TMG

TMG TMG-DT3380 Manuel utilisateur

TMG

TMG PRO Series Manuel utilisateur

TMG

TMG TMG-DT5040CG Manuel utilisateur

TMG

TMG TMG-ST3070V-2.0 Manuel utilisateur

TMG

TMG PRO Series Manuel utilisateur

TMG

TMG TMG-ST2020L Manuel utilisateur

TMG

TMG TMG-ST2040C-1.0 Manuel utilisateur

TMG

TMG TMG-LCP16 Manuel utilisateur

TMG

TMG TMG-ST3040C Manuel utilisateur

TMG

TMG TMG-CP2030F-1.0 Manuel utilisateur

TMG

TMG TMG-DT40FW8 Manuel utilisateur

TMG

TMG TMG-DT50FW8 Manuel utilisateur

TMG

TMG TMG-ST4061E Manuel utilisateur

TMG

TMG TMG-DT3041 Manuel utilisateur

TMG

TMG TMG-184517ST Manuel utilisateur

TMG

TMG PRO Series Manuel utilisateur

TMG

TMG TMG-MSC2030F Manuel utilisateur

TMG

TMG TMG-SCE20 Manuel utilisateur

TMG

TMG TMG-MS2119 Manuel utilisateur

TMG

TMG TMG-DT70120-PRO Manuel utilisateur

TMG

TMG TMG-DT3063-PRO Manuel utilisateur

TMG

TMG TMG-DT3081 Manuel utilisateur

Manuels Abri populaires d'autres marques

Tempo Fitness

Tempo Fitness S11 Manuel utilisateur

Tuindeco

Tuindeco 42.7906 Manuel utilisateur

No Butts Bin

No Butts Bin SR1605 Manuel utilisateur

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manuel utilisateur

Kampa

Kampa Poled Shelter 300 Manuel utilisateur

Harnois

Harnois TA-R Manuel utilisateur

Shelters4Less

Shelters4Less SR1551 Manuel utilisateur

Vikre Handel AS

Vikre Handel AS JIT-1216 Manuel utilisateur

VARNA buildings

VARNA buildings C2020H Manuel utilisateur

Storage Canopy

Storage Canopy C3340R Manuel utilisateur

Frabill

Frabill ICE HUNTER 195 Manuel utilisateur

Shelters4Less

Shelters4Less SR1588 Manuel utilisateur

Sealey

Sealey Power Products GSS150819SD Manuel utilisateur

Crivit

Crivit 104155 Manuel utilisateur

No Butts Bin

No Butts Bin SR1558-F Manuel utilisateur

Storage Canopy

Storage Canopy C3340DTPR Manuel utilisateur

Storage Canopy

Storage Canopy C4040DTR Manuel utilisateur

NBB

NBB SR8062-F Manuel utilisateur