TMG PRO Series Manuel utilisateur

W W W . T M G I N D U S T R I A L . C O M P 1 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Main Specifications :

Overall assembled size : W9.15 x L11.97 x H3.0 (m) / 30 x 40 x 10(ft)

Ridge Peak Height : 3 m / 10ft + container height

Prior to assembly

Please read the instructions carefully before installation. It is very important to

follow your local safety regulations and industry standards during installation.

Regulations may include but are not limited to:

Safety helmets, protective eyewear, and clothing

Safety harnesses for all elevated workers

Proper ladder, cage, and safety operation

Check all components and parts before installation. All parts are marked with a part

number, please refer to the parts list to make sure you have all parts.

Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not

make any alterations to the structure. Do not hang any weights on the frame during

installation, including parts. We are not responsible for any damages or injuries caused by

inappropriate installation, unauthorized modifications or extreme weather.

This building is not intended for human occupancy.

It is recommended to tape or add foam/rubber on the frame where joints connect and

where it touches the cover. This will help extend the life span of the cover.

Read the following item list carefully and count the number of items to ensure that all

parts are included prior to setup.

Installation steps

Step 1 : Review the whole structure and choose the proper installation site

Choose a solid flat level ground area to set up the building. Do not install the building on

soft ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that are not

rated to hold its weight.

We strongly recommend that you put the containers on hard foundations before installing

the shelter.

Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames

W W W . T M G I N D U S T R I A L . C O M P 2 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

or exposed electrical wires. Do not keep heat sources near the fabric cover. Keep the

building surroundings clear at all times.

TMG-ST3040CVF Part List

No.

Picture

Description

Quantity

Peak arch tube

Middle rafter tube

Shoulder tube

Middle truss baseplate

Left corner baseplate

(front and rear truss)

Right corner baseplate

(front and rear truss)

Middle column baseplate

(rear truss)

Middle column baseplate

(rear truss)

Roof purlin

(horizontal tube)

Ceiling cross bar

Sidewall frame steel

tension cables

W W W . T M G I N D U S T R I A L . C O M P 3 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Ratchet

Ratchet straps

Mounting base

Cable connection plate

Top cover tension tube

(for both bottom sides)

Top cover tension tube

Rear cover tension tube

Door frame lower tube

(rear truss)

Door frame lower tube

(rear truss)

11A

Door frame upper tube

(rear truss)

Door frame upper tube

(rear truss)

12A

Door frame upper tube

(rear truss)

Roof purlin

14A

Roof purlin

Tube clamp

15A

Tube clamp

Self locking bolt

M10x80mm

Self locking bolt

M8x70mm

130

W W W . T M G I N D U S T R I A L . C O M P 4 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Hex bolt

M10x30mm

Hex bolt

M10x50mm

Self locking bolt

M8x80mm

Top cover

Front cover panel

22A

Rear cover panel

Braided rope (120m)

Scratch resistant tape

Water plug

Expansion bolt

ф16x150mm

Step 2 : Place the containers making sure they are parallel and the correct width

apart. Make sure there is a gap of about 3 feet around the building. the center point

of the round pipe of the base is the reference point, and the diagonal X and Y must

be equal. The base plate shall be welded to the top of the container on the same

horizontal plane to ensure that the welding is firm and reliable. (refer to picture 1）

Components are :

(16) Middle truss baseplate (#4)

(2) Left corner baseplate (#4L)

(2) Right corner baseplate (#4R)

W W W . T M G I N D U S T R I A L . C O M P 5 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

(2) Middle column baseplate (#4A)

(3) Middle column baseplate (#4B)

(10) Expansion bolt (#26)

Picture 1

Step 3 : Connect all trusses

Layout all truss components on the ground in the correct configuration before bolting

them together.

The building includes 10 trusses : (1) front truss, (1) rear truss, and (8) middle trusses.

The front and the rear truss are to install with the fabric panel (#22 and #22A).

Parts used to install the front truss in this step (refer to Picture 2) :

W W W . T M G I N D U S T R I A L . C O M P 6 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

(1) Peak arch tube (#1)

(2) Middle rafter tube (#2A)

(2) Shoulder tube (#3)

(1) Ceiling cross bar (#6A)

(1) Ceiling cross bar (#6B)

(2) Hex bolt (#19)

(8) Half round head bolt (#17)

(2) Hex bolt M10x30mm (#18)

(2) Self locking bolt M8x80mm (#20)

Picture 2

Parts used to install the rear truss in this step (refer to Picture 3) :

(1) Peak arch tube (#1)

(2) Middle rafter tube (#2)

(2) Shoulder tube (#3A)

(1) Ceiling cross bar (#6)

(8) Self locking bolt M8x70mm (#17)

(2) Hex bolt M10x30mm (#18)

Picture 3

W W W . T M G I N D U S T R I A L . C O M P 7 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Parts used to install the middle truss in this step (refer to Picture 4) :

(1x8) Peak arch tube (#1)

(2x8) Middle rafter tube (#2)

(2x8) Shoulder tube (#3)

(1x8) Ceiling cross bar (#6)

(8x8) Self locking bolt M8x70mm (#17)

(2x8) Hex bolt M10x30mm (#18)

Picture 4

Lay down all (10) trusses on the ground when the assembly is all completed and before

moving to next step, and then wrap (#24) around the sharp points of the joint to avoid

friction between the fabric and the interface, resulting in fabric damage ( picture 5).

(2) Scratch resistant tape (#24)

Picture 5

W W W . T M G I N D U S T R I A L . C O M P 8 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Step 4 : Put up all trusses

Install each truss on the base tube. Use bolt (#17) to secure the truss to the base

tube firmly. We recommend to use a crane or forklift to lift the truss and have 2 to

3 people on site to work together. Please make sure it is safe and secure when

installation is proceeding. (refer to picture 6 )

Components are :

(40) Self locking bolt M8x70mm (#17)

Picture 6

Connect all purlins (#5) with bolt (#16). Tension cable installation . (refer to picture 7)

Components are :

(63) Roof purlin (#5)

(8) Sidewall frame steel tension cables (#7)

(8) Mounting base (#8)

(8) Cable connection plate (#8A)

(70) Self locking bolt M10x80mm (#16)

W W W . T M G I N D U S T R I A L . C O M P 9 / 13 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

Picture 7

Step 5 : Install the remaining parts on the front truss (refer to picture 8)

Components are :

(1) Door frame upper tube (#12A)

(1) Self locking bolt M8x80mm (#20)

Picture 8

Autres manuels pour PRO Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TMG Abri

TMG

TMG TMG-DT4041C Manuel utilisateur

TMG

TMG TMG-ST3070V-2.0 Manuel utilisateur

TMG

TMG TMG-CP2000-RD110 Manuel utilisateur

TMG

TMG TMG-CRS1020 Manuel utilisateur

TMG

TMG PRO Series Manuel utilisateur

TMG

TMG TMG-ST4061E Manuel utilisateur

TMG

TMG TMG-ST3041CE Manuel utilisateur

TMG

TMG TMG-DT5040CG Manuel utilisateur

TMG

TMG TMG-DT4041CG Manuel utilisateur

TMG

TMG PRO Series Manuel utilisateur

TMG

TMG TMG-ST2041V Manuel utilisateur

TMG

TMG TMG-DT2030-PRO Manuel utilisateur

TMG

TMG TMG-MSC2020 Manuel utilisateur

TMG

TMG TMG-DT3380 Manuel utilisateur

TMG

TMG TMG-MSC1220F Manuel utilisateur

TMG

TMG TMG-DT3063-PRO Manuel utilisateur

TMG

TMG TMG-CP1220F Manuel utilisateur

TMG

TMG TMG-ST3040V-1.0 Manuel utilisateur

TMG

TMG TMG-MS2030LC Manuel utilisateur

TMG

TMG TMG-DT3380 Manuel utilisateur

TMG

TMG TMG-184517ST Manuel utilisateur

TMG

TMG TMG-DT40FW8 Manuel utilisateur

TMG

TMG ST2030 Manuel utilisateur

TMG

TMG TMG-MSC2030F Manuel utilisateur

Manuels Abri populaires d'autres marques

Tempo Fitness

Tempo Fitness S11 Manuel utilisateur

Tuindeco

Tuindeco 42.7906 Manuel utilisateur

No Butts Bin

No Butts Bin SR1605 Manuel utilisateur

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manuel utilisateur

Kampa

Kampa Poled Shelter 300 Manuel utilisateur

Harnois

Harnois TA-R Manuel utilisateur

Shelters4Less

Shelters4Less SR1551 Manuel utilisateur

Vikre Handel AS

Vikre Handel AS JIT-1216 Manuel utilisateur

VARNA buildings

VARNA buildings C2020H Manuel utilisateur

Storage Canopy

Storage Canopy C3340R Manuel utilisateur

Frabill

Frabill ICE HUNTER 195 Manuel utilisateur

Shelters4Less

Shelters4Less SR1588 Manuel utilisateur

Sealey

Sealey Power Products GSS150819SD Manuel utilisateur

Crivit

Crivit 104155 Manuel utilisateur

No Butts Bin

No Butts Bin SR1558-F Manuel utilisateur

Storage Canopy

Storage Canopy C3340DTPR Manuel utilisateur

Storage Canopy

Storage Canopy C4040DTR Manuel utilisateur

NBB

NBB SR8062-F Manuel utilisateur