Thermo Scientific 30M Mode d'emploi

hermo Scientific

Precision 30 cu ft Incubator

Standard or Low emperature

Operating and Maintenance Manual 3177878 Rev.

Visit us online to register your warranty

www.thermoscientific.com/labwarranty

Thermo Scientific

MANUAL NUMBER 3177878

41371 8/8/17 Updated 3975 and 3977 electrical schematics bpg

M 41670 7/17 Uodated uniformity pg 4-2, electrical connections pg 6-1 bpg

L -- 9/10 3175235 to 3175237 t-stat on pgs 10-14

K -- 8/10 Parts List - pg 10

J -- 4/09 3975-70-1-D to rev 2, corrected 3175235 to 3175237 - pgs 13 & 14

I 24002/I -3770 2/09 3175274 to 3185253, 3175277 to 3185254-Parts List pg 10, reformat schematics

H 23717/I -3733 12/06 3173630 relay to 300175

G -- 1/06 P/ 3167106 to 3166985, 3174933 to 3174924 - pg 10

F -- 6/05 Manual number and manufacture location - was 36100113

E -- 6/03 Add notices page, update instructions for setting safety and control thermostats-pg 7

D -- 11/01 Add environmental conditions - pgs. 2-3

C -- 2/01 Add part numbers for new doors and gasket - pg 10

B -- 8/99 Update parts list for new kit numbers - pg 10

A -- 6/99 Initial Release

Preface

30 cu ft Incubators i

Standard emperature

Model 30M Voltage Door

3971 120V, 50/60 Hz., 1450W Solid

3973 120V, 50/60 Hz., 1450W Glass

Low emperature (Refrigerated)

Model 30MR Voltage Door

3975 120V, 60 Hz., 2150W Solid

3977 120V, 60 Hz., 2150W Glass

Thermo Scientificii 30 cu ft Incubators

Preface

Contains Parts and Assemblies

Susceptible to Damage by

Electrostatic Discharge (ESD)

CAUTION

Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual

may result in damage to the unit, injury to operating personnel, and poor equipment performance. s

Caution All internal adjustments and maintenance must be performed by qualified service personnel. s

Material in this manual is for information purposes only. The contents and the product it describes are subject

to change without notice. Thermo Fisher Scientific makes no representations or warranties with respect to this

manual. In no event shall Thermo be held liable for any damages, direct or incidental, arising out of or related to

the use of this manual.

Thermo Scientific 30 cu ft Incubators iii

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this

symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Hot surface(s) present which may cause burns to unprotected skin, or to materials which may be

damaged by elevated temperatures.

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment

falling under the Directive 2002/96/EC (WEEE) and the equipment that has been put on the market

after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic

Equipment (WEEE) Directive 2002/96/EC. It is marked with the WEEE symbol. Thermo Fisher

Scientific has contracted with one or more recycling/disposal companies in each EU Member State

European Country, and this product should be disposed of or recycled through them. Further

information on Thermo’s compliance with this directive, the recyclers in your country and

information on Thermo Scientific products will be available at www.thermofisher.com.

4Always use the proper protective equipment (clothing, gloves, goggles, etc.)

4Always dissipate extreme cold or heat and wear protective clothing.

4Always follow good hygiene practices.

4Each individual is responsible for his or her own safety.

Thermo Scientificiv 30 cu ft Incubators

Preface

Do You Need Information or Assistance on

Thermo Scientific Products?

If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at:

1-740-373-4763 Direct

1-800-438-4851 Toll Free, U.S. and Canada

1-877-213-8051 FAX

http://www.thermofisher.com Internet Worldwide Web Home Page

service.led.marietta@thermofisher.com Tech Support Email Address

Certified Service Web Pagewww.unitylabservices.com

Our staff can provide information on pricing and give you quotations. We canSales Support

take your order and provide delivery information on major equipment items or make

arrangements to have your local sales representative contact you. Our products are listed on the

Internet and we can be contacted through our Internet home page.

Our staff can supply technical information about proper setup, operation orService Support

troubleshooting of your equipment. We can fill your needs for spare or replacement parts or

provide you with on-site service. We can also provide you with a quotation on our Extended

Warranty for your Thermo Scientific products.

Whatever Thermo Scientific products you need or use, we will be happy to discuss your

applications. If you are experiencing technical problems, working together, we will help you

locate the problem and, chances are, correct it yourself...over the telephone without a service

call.

When more extensive service is necessary, we will assist you with direct factory trained

technicians or a qualified service organization for on-the-spot repair. If your service need is

covered by the warranty, we will arrange for the unit to be repaired at our expense and to your

satisfaction.

Regardless of your needs, our professional telephone technicians are available to assist you

Monday through Friday from 8:00 a.m. to 6:00 p.m. Eastern Time. Please contact us by

telephone or fax. If you wish to write, our mailing address is:

Thermo Fisher Scientific (Asheville) LLC

401 Millcreek Road, Box 649

Marietta, OH 45750

International customers, please contact your local Thermo Scientific distributor.

30 cu ft Incubators vThermo Scientific

able of Contents

Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

eneral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Unpacking and Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Explanation of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2

Parts Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Section 1

Section 2

Section 3

Section 4

Section 5

Section 6

Section 8

Section 7

Section 9

30 cu ft Incubators 1-1Thermo Scientific

General

Section 1 Cautions and Warnings

Caution Read these notices before installing the unit. s

As a routine laboratory precaution, always wear safety glasses when

working with this apparatus.

Allow the incubator to cool to approximately 100°F (38°C) before

changing from HEAT to COOL switch positions.

The uniformity will be adversely affected if air circulation is obstructed.

DO NOT place any explosive, combustible, or flammable materials in the

chamber.

DO NOT place sealed containers in the chamber. Sealed containers, filled

with materials, do not provide room for expansion and can develop

dangerous vapor pressure as the temperature increases.

Avoid spillage of large volumes of liquids.

DO NOT evaporate noxious fumes.

The liquid level in the container should be checked daily to prevent

overflow.

Allow a 4°C differential between the desired operating temperature and the

safety temperature.

1-2 30 cu ft Incubators Thermo Scientific

Section 1

Cautions and Warnings

For personal safety, this apparatus must be properly grounded.

Be sure that the power supply is of the same voltage as specified on the

nameplate.

DO NOT connect an instrument, or a second instrument, to the

convenience outlet that exceeds a total of 15 amps, as circuit overload will

result

DO NOT, under any circumstances, cut or remove the third (ground)

prong from the power cord. DO NOT use a two-prong adapter plug.

Hazardous high voltage conditions exist inside the control compartment.

Disconnect all electrical power to the incubator before removing the

cover. Only qualified electrical instrument personnel are authorized to

perform troubleshooting and/or servicing.

Electrical

30 cu ft Incubators 2-1Thermo Scientific

Section 2 Introduction

15AMPS MAX

OOFFFF

OONN

INTERIOR HEAT

OOFFFF

OONN

TEMP.INCREASE

CONTROL

TEMP.INCREASE

SAFETY

350

OFF

700

WATTAGE

1400

LINE

Figure 2-1. Standard Temperature Model 30M (3971, 3973) Figure 2-2. Low Temperature Model 30MR (3975, 3977)

INTERIOR

15AMPS MAX

OFF

HEAT

COOL

OFF

Caution:

Afterturning

compressorOff.

Wait3 minutes

beforerestarting.

CONTROL

TEMP.INCREASE

SAFETY

TEMP.INCREASE 350

WATTAGE

OFF

700

1400

LINE

2-2 30 cu ft Incubators Thermo Scientific

Section 2

Introduction

Your satisfaction and safety are important to Thermo and a complete

understanding of this unit is necessary to attain these objectives.

As the ultimate user of this apparatus, it is your responsibility to

understand its proper function and operational characteristics. This

instruction manual should be thoroughly read and all operators given

adequate training before attempting to place this unit in service.

Awareness of the stated cautions and warnings, and compliance with

recommended operating parameters--together with maintenance

requirements--are important for safe and satisfactory operation. The unit

should be used for its intended application; alterations or modifications

will void the warranty.

Warning As a routine laboratory precaution, always wear safety glasses

when working with this apparatus. s

Caution This product is not intended, nor can it be used, as a sterile or

patient connected device. In addition, this apparatus is not designed for

use in Class I, II, or III locations as defined by the National Electrical

Code. s

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Thermo Scientific Accessoires

Thermo Scientific

Thermo Scientific iEMS Incubator Manuel utilisateur

Thermo Scientific

Thermo Scientific Orion RDO Manuel utilisateur

Thermo Scientific

Thermo Scientific 314 Manuel utilisateur

Thermo Scientific

Thermo Scientific Heracell 240i Manuel utilisateur

Thermo Scientific

Thermo Scientific Steri-Cycle i160 CR Manuel utilisateur

Thermo Scientific

Thermo Scientific 2862 Mode d'emploi

Thermo Scientific

Thermo Scientific IMH 60 Manuel utilisateur

Thermo Scientific

Thermo Scientific Cytomat 2 Manuel utilisateur

Thermo Scientific

Thermo Scientific 3403 Manuel utilisateur

Thermo Scientific

Thermo Scientific 370 Mode d'emploi

Thermo Scientific

Thermo Scientific BB 150 Manuel utilisateur

Thermo Scientific

Thermo Scientific Smart-Vue Manuel d'utilisation et d'entretien

Thermo Scientific

Thermo Scientific Lab-Line Imperial 3 Mode d'emploi

Thermo Scientific

Thermo Scientific 3010 Mode d'emploi

Thermo Scientific

Thermo Scientific RMI300S-9-A Mode d'emploi

Thermo Scientific

Thermo Scientific Lab-Line 100 Mode d'emploi

Thermo Scientific

Thermo Scientific 3110 Mode d'emploi

Thermo Scientific

Thermo Scientific 8000DH Series Manuel utilisateur

Thermo Scientific

Thermo Scientific 2076 Series Manuel utilisateur

Thermo Scientific

Thermo Scientific Neslab Dimax Manuel utilisateur

Thermo Scientific

Thermo Scientific 8000DH Series Mode d'emploi

Thermo Scientific

Thermo Scientific Heracell 150i Manuel utilisateur

Thermo Scientific

Thermo Scientific 60-12 Manuel de service

Thermo Scientific

Thermo Scientific Unity Lab Services 3307 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur