Thermo Scientific Precision 818 Mode d'emploi

Visit us online to register your warranty

www.thermoscientific.com/labwarranty

User Manual

Thermo Scientific Precision

Model 818 Incubator

Plant Growth Chamber - Microprocessor Controlled

Operating and Maintenance Manual 7013758 Rev. 1

Thermo Scientific

Manual Number 7013758

1 40905 6/8/17 Added Chinese info bpg

0 40096 4/3/15 Original - new cabinet size, technical data ccs

ev EC /ECN Date Description By

Preface

Plant Growth Chamber i

Catalog Number (Model) Volume

(L /cu. ft.) Voltage

PR505755L (3759) 504/17.8 120V

PR505750L (3758) 504/17.8 230V

PR505750L-CN 504/17.8 230V

Covered in this manual:

Thermo Scientificii Plant Growth Chamber

Preface

Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual

may result in damage to the unit, injury to operating personnel, and poor equipment performance. s

Caution All internal adjustments and maintenance must be performed by qualified service personnel. s

Warning If the growth chamber is not used in the manner specified in this operating manual, the protection

provided by the equipment design may be impaired. s

Warning Hot/warm surface(s) can occur. epending on ambient termperature and settings, surface can become

warm (up to 60°C). s

Material in this manual is for information purposes only. The contents and the product it describes are subject

to change without notice. Thermo Fisher Scientific makes no representations or warranties with respect to this

manual. In no event shall Thermo be held liable for any damages, direct or incidental, arising out of or related to

the use of this manual.

Contains Parts and Assemblies

Susceptible to Damage by

Electrostatic Discharge (ESD)

CAUTION

Thermo Scientific Plant Growth Chamber iii

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this

symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment

falling under the irective 2002/96/EC (WEEE) and the equipment that has been put on the market

after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic

Equipment (WEEE) irective 2002/96/EC. It is marked with the WEEE symbol. Thermo Fisher

Scientific has contracted with one or more recycling/disposal companies in each EU Member State

European Country, and this product should be disposed of or recycled through them. Further

information on Thermo’s compliance with this directive, the recyclers in your country and information

on Thermo Scientific products will be available at www.thermoscientific.com.

4Always use the proper protective equipment (clothing, gloves, goggles, etc.)

4Always dissipate extreme cold or heat and wear protective clothing.

4Always follow good hygiene practices.

4Each individual is responsible for his or her own safety.

Thermo Scientificiv Plant Growth Chamber Thermo Scientific

Preface

Do You Need Information or Assistance on

Thermo Scientific Products?

If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at:

1-740-373-4763 Direct

1-800-438-4851 Toll Free, U.S. and Canada

1-877-213-8051 FAX

http://www.thermofisher.com Internet Worldwide Web Home Page

service.led.marietta@thermofisher.com Tech Support Email Address

Certified Service Web Pagewww.unitylabservices.com

Our staff can provide information on pricing and give you quotations. We canSales Support

take your order and provide delivery information on major equipment items or make

arrangements to have your local sales representative contact you. Our products are listed on the

Internet and we can be contacted through our Internet home page.

Our staff can supply technical information about proper setup, operation orService Support

troubleshooting of your equipment. We can fill your needs for spare or replacement parts or

provide you with on-site service. We can also provide you with a quotation on our Extended

Warranty for your Thermo Scientific products.

Whatever Thermo Scientific products you need or use, we will be happy to discuss your

applications. If you are experiencing technical problems, working together, we will help you

locate the problem and, chances are, correct it yourself...over the telephone without a service

call.

When more extensive service is necessary, we will assist you with direct factory trained

technicians or a qualified service organization for on-the-spot repair. If your service need is

covered by the warranty, we will arrange for the unit to be repaired at our expense and to your

satisfaction.

Regardless of your needs, our professional telephone technicians are available to assist you

Monday through Friday from 8:00 a.m. to 6:00 p.m. Eastern Time. Please contact us by

telephone or fax. If you wish to write, our mailing address is:

Thermo Fisher Scientific (Asheville) LLC

401 Millcreek Road, Box 649

Marietta, OH 45750

International customers, please contact your local Thermo Scientific distributor.

Thermo Scientific Plant Growth Chamber v

Thermo Scientific

Preface

Warranty Notes

Information You Should Know Before Requesting Warranty Service

•Locate the model and serial numbers. A serial tag is located on the unit itself.

• For equipment service or maintenance, or with technical or special application inquiries, contact Technical

Services at 1-800-438-4851 or 1-740-373-4763 (USA and Canada). Outside the USA, contact your local

distributor.

Repairs NOT Covered Under Warranty

• Calibration of control parameters. Nominal calibrations are performed at the factory; typically ±1°C for

temperature, ±1% for gases, and ±5% for humidity. Our service personnel can provide precise calibrations as

a billable service at your location. Calibration after a warranty repair is covered under the warranty.

• Damage resulting from use of improper quality water, chemicals or cleaning agents detrimental to

equipment materials.

• Service calls for improper installation or operating instructions. Corrections to any of the following

are billable services:

1) electrical service connection

2) tubing connections

3) gas regulators

4) gas tanks

5) unit leveling

6) room ventilation

7) adverse ambient temperature fluctuations

8) any repair external to the unit

• Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, or improper

installation.

• Repairs to parts or systems resulting from unauthorized unit modifications.

• Any labor costs other than that specified during the parts and labor warranty period, which may

include additional warranty on CO2sensors, blower motors, water jackets, etc.

Section 4

Section 5

Section 6

Section 8

Section 7

Plant Growth Chamber viThermo Scientific

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Unpacking and amage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Performance ata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Explanation of Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Explanation of Auxiliary Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Instrumentation Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Operation and Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

To Lock the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

To Unlock the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Adjusting the Intake and Exhaust Ports . . . . . . . . . . . . . . . . . . . . . . 3-10

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Symptoms and Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Possible Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

General Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Setting Up the Incubator for Communication . . . . . . . . . . . . . . . . 6-2

Setting up the Computer for Communication . . . . . . . . . . . . . . . . 6-5

Using the Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Section 1

Section 2

Section 3

Plant Growth Chamber 1-1Thermo Scientific

Section 1 Introduction

Your satisfaction and safety are important to Thermo and a complete

understanding of this unit is necessary to attain these objectives.

Warning As a routine laboratory precaution, always wear safety glasses

when working with this apparatus. s

This product is not intended, nor can it be used, as a sterile or patient

connected device. In addition, this apparatus is not designed for use in

Class I, II or III locations as defined by the National Electrical Code.

Save all packing material until unit is put into service. This merchandise

was carefully packed and thoroughly inspected before leaving our factory.

Responsibility for safe delivery was assumed by the carrier upon acceptance

of the shipment; therefore, claims for loss or damage sustained in transit

must be made upon the carrier by the recipient as follows:

1. Visible Loss or amage: Note any external evidence of loss or damage

on the freight bill, or express receipt, and have it signed by the carrier's

agent. Failure to adequately describe such external evidence of loss or

damage may result in the carrier's refusing to honor your damage

claim. The form required to file such claim will be supplied by the

carrier.

2. Concealed Loss or amage: Concealed loss or damage means loss or

damage which does not become apparent until the merchandise has

been unpacked and inspected. Should either occur, make a written

request for inspection by carrier's agent within fifteen (15) days of the

delivery date; then file a claim with the carrier since the damage is the

carrier's responsibility.

If you follow the above instructions carefully, we will guarantee our full

support of your claim to be compensated for loss or concealed damage.

Note o not - for any reason - return this unit without first obtaining

authorization. In any correspondence to Thermo, please supply the

nameplate data, including catalog number and serial number. s

Unpacking and

Damage

1-2 Plant Growth Chamber Thermo Scientific

Section 1

Introduction

The growth chamber has been commonly referred to as the standard

model 818.

The PR505750L can be converted for operation on 200V or 240V by

changing the input connections to the autotransformers (see wiring

diagram at the end of this manual).

The PR505750L/PR505755L Plant Growth Chamber has been designed

to provide the ultimate in temperature control. The user is assured of

dependable and precise performance through the use of microprocessor

technology in the temperature control circuitry. This growth chamber is

operable in the range of -10° to 50°C without illumination, and +10°C to

+50°C with illumination. These temperature ranges will meet a wide

variety of applications, such as BO determination, general incubation,

as well as the preservation of critical materials.

*with d r illuminati n switch n

General Information

Performance Data

Set

temperature

Uniformity values:

Temperature deviation

from set value, spatial

(3 point measurement)

Uniformity values:

Temperature deviation

from set value, spatial

(27 point measurement

according to DIN 12880)

Temperature stability:

Maximum temperature

difference at chamber

center point (1 point

measurement)

Energy

consumption

Heat up time / Cool

down time from

ambient temperature

according to DIN

12880

Recovery time

after door open-

ing according to

DIN 12880

-10°C ±0.8°C ±1.3°C ≤ ±0.25°C ≤ 0.3 kW ca. 80 min ca. 10 min

+10°C ±0.6°C / ±0.2°C ±1.9°C / ±1.3°C ≤ ±0.25°C ≤ 0.54 kW /

≤ 0.52 kW ca. 54 min.* ca. 4 min.

+20°C ±0.5°C / ±0.2°C ±1.8°C / ±0.9°C ≤ ±0.20°C ≤ 0.55 kW /

≤ 0.49 kW N/A N/A

+50°C ±0.25°C / ±0.15°C ±1.1°C / ±0.9°C ≤ ±0.15°C ≤ 0.56 kW /

≤ 0.51 kW ca. 100 min. * ca. 42 min. *

Note The above performance figures are based upon the following operating conditions:

- Ambient temperature of 22°C, ±3°C

- Line voltage 120V, ±5% (120V version) and 230V, ±5V (230V version)

The following test protocols have been used:

3 point measurement test: 1 thermocouple sensor in center of each shelf - 1 shelf top position, 1 shelf lowest

position, 1 shelf middle position

27 point measurement test: 9 x thermocouples on each shelf - 1 shelf top position, 1 shelf lowest position, 1

shelf middle position (based on IN 12880)

1 point measurement test: 1 thermocouple at chamber center point (temporal temperature variation

characterized by the maximum temperature difference)

The refrigeration system, defrost heater, and air circulating fan are used in

conjunction with a microprocessor controlled proportioning circuit to

achieve sensitive temperature control. An RT (Resistance Temperature

etector) located in the airstream senses any temperature deviation from

the control point, and heat is provided proportionally to maintain the

desired temperature. Regardless of what temperature is being maintained,

the compressor operates continuously. This constant operation alleviates

component failures associated with cycle type operation.

The circulating fan provides even air distribution throughout the chamber

and ensures temperature uniformity.

The program mode of PR505750L/PR505755L plant growth chamber

allows the user to program into memory 2 sets of values for time, setpoint

temperature, and light condition per day for a full week. The following is

an example of a schedule and a pictorial describing the events during that

week. A blank schedule sheet is provided toward the end of the manual for

the user to copy, then document a schedule. It is strongly recommended to

do this before any programming is performed.

The growth chamber leaves the factory with a default schedule as follows:

Hr1 1am Hr2 1pm

Min1 00 Min2 00

Set1 20.0 Set2 20.0

LGT1 OFF LGT2 OFF

Plant Growth Chamber 1-3Thermo Scientific

Section 1

Introduction

Theory of Operation

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Thermo Scientific Accessoires

Thermo Scientific

Thermo Scientific IMP 180 Manuel utilisateur

Thermo Scientific

Thermo Scientific 3110 Manuel utilisateur

Thermo Scientific

Thermo Scientific 3010 Mode d'emploi

Thermo Scientific

Thermo Scientific BB 150 Manuel utilisateur

Thermo Scientific

Thermo Scientific Lab-Line 100 Mode d'emploi

Thermo Scientific

Thermo Scientific IMH 60 Manuel utilisateur

Thermo Scientific

Thermo Scientific Cytomat 2 Manuel utilisateur

Thermo Scientific

Thermo Scientific Emerald Wireless Remote Sensor Manuel du propriétaire

Thermo Scientific

Thermo Scientific Orion RDO Manuel utilisateur

Thermo Scientific

Thermo Scientific 2076 Series Manuel utilisateur

Thermo Scientific

Thermo Scientific 2862 Mode d'emploi

Thermo Scientific

Thermo Scientific Heracell 240i Manuel utilisateur

Thermo Scientific

Thermo Scientific Ramsey MINI CK100 Manuel de service

Thermo Scientific

Thermo Scientific 310 Series Manuel utilisateur

Thermo Scientific

Thermo Scientific 3110 Mode d'emploi

Thermo Scientific

Thermo Scientific AquaSensors AnalogPlus Manuel utilisateur

Thermo Scientific

Thermo Scientific HERACELL VIOS 160i Manuel utilisateur

Thermo Scientific

Thermo Scientific 3010 Mode d'emploi

Thermo Scientific

Thermo Scientific 61-12C Manuel de service

Thermo Scientific

Thermo Scientific Heracell 150i Manuel utilisateur

Thermo Scientific

Thermo Scientific RMI300S-9-A Mode d'emploi

Thermo Scientific

Thermo Scientific 370 Mode d'emploi

Thermo Scientific

Thermo Scientific 60-12 Manuel de service

Thermo Scientific

Thermo Scientific Thermo Fisher 3900 Series Mode d'emploi

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur