Texas Instruments Chipcon Products CC2400DK Manuel utilisateur

SWRU050 Page 1 of 35

User Manual

Rev. 1.1

CC2400DK Development Kit

SWRU050 Page 2 of 35

Table of contents

INTRODUCTION....................................................................................................................... 3

EVALUATION MODULE........................................................................................................... 4

CIRCUIT DESCRIPTION .............................................................................................................. 4

PCB LAYOUT ........................................................................................................................... 4

SCHEMATIC ............................................................................................................................ 10

EVALUATION BOARD........................................................................................................... 12

POWER SUPPLY SECTION ........................................................................................................ 12

USB INTERFACE..................................................................................................................... 14

RS-232 INTERFACE................................................................................................................ 14

JUMPERS ............................................................................................................................... 14

MICROCONTROLLER AND FPGA.............................................................................................. 15

CONNECTORS ........................................................................................................................ 16

PCB LAYOUT ......................................................................................................................... 17

SCHEMATICS,CC2400EB...................................................................................................... 20

BILL OF MATERIALS,CC2400EB ............................................................................................ 25

USING THE DEVELOPMENT KIT.......................................................................................... 31

CC2400 RF EVALUATION USING SMARTRF®STUDIO............................................................... 31

USING THE CC2400DK FOR PROTOTYPING ............................................................................. 32

TROUBLESHOOTING............................................................................................................ 33

IT DOES NOT WORK................................................................................................................. 33

SMARTRF®STUDIO DOES NOT RECOGNIZE THE CC2400EB .................................................... 33

SWRU050 Page 3 of 35

Introduction

The CC2400 single-chip RF transceiver provides a highly integrated, flexible low-cost solution

for applications using the worldwide unlicensed 2.4 GHz frequency band. The CC2400DK

development kit is a powerful and flexible tool specifically designed to make it easy for the

user to evaluate the RF performance of the CC2400 and to minimize the time spent on

evaluation.

The Development Kit includes two Evaluation Boards and two Evaluation Modules. The

Evaluation Modules contain the CC2400 chip and required external components.

The Evaluation Board serves as a motherboard for the Evaluation Modules. The Evaluation

Board provides a USB port, a serial port, buttons, LEDs, voltage regulator, configuration

jumpers and connectors to make it easy to interface the CC2400 with the SmartRF®Studio

software and various test equipment.

This User Manual describes how to use the Development Kit. SmartRF®Studio is

documented in its own user manual.

Your SmartRF®CC2400DK Development Kit should contain the following items:

Kit contents

Item Number of articles

Evaluation Board (CC2400EB) 2

Evaluation Module (CC2400EM) 2

Quick Start instructions 1

Antenna, 50Ωquarter-wave monopole, SMA male connector 2

SMA to BNC adapters 4

USB cable 2

CC2400 sample kit 1

SWRU050 Page 4 of 35

Evaluation Module

The Evaluation Module contains the CC2400 chip together with the needed external circuitry

for operation. Not all components are needed in an actual application. Please see the

datasheet for a typical application circuit.

The CC2400 operates in the 2.4 GHz frequency band. Although this frequency band is

usually described as “world-wide”, some countries do not allow unlicensed operation in this

band. Please refer to application note AN001 for more information about applicable

regulations.

Important: Contact your local telecommunication authorities before transmitting an RF signal.

Circuit description

The CC2400 RF section includes all the necessary components for correct operation.

The CC2400 is connected to a 16 MHz crystal.

The Evaluation Module can be plugged into the Evaluation Board. Two 2x10 pin pin row

connectors with 0.050-inch pitch are used for this purpose.

Figure 1: CC2400EM Evaluation Module

PCB layout

RF circuits operating at high frequencies are sensitive to the physical layout of the PCB.

Chipcon has carefully optimized the layout of the CC2400EM evaluation module and we

therefore recommend that the user copies it when making own PCB designs.

The PCB is of a 4-layer type in order to provide a well-defined ground plane as well as

adequate routing space. The laminate used is standard FR-4 board material. The PCB is

1.0mm thick, with layer 1 on the top side, layers 2 and 3 are internal layers and layer 4 is on

the bottom side. Layers 1 and 4 are used for routing, while layer 2 is a ground plane and layer

3 is used for power routing. All areas not utilized for routing are filled with copper connected

to ground to provide RF shielding. The ground planes on all layers are stitched together with

closely spaced vias.

SWRU050 Page 5 of 35

Figure 2: CC2400EM PCB layout, layer 1

SWRU050 Page 6 of 35

Figure 3: CC2400EM PCB layout, layer 2

SWRU050 Page 7 of 35

Figure 4: CC2400 PCB layout, layer 3

SWRU050 Page 8 of 35

Figure 5: CC2400EM PCB layout, layer 4

SWRU050 Page 9 of 35

Figure 6: CC2400EM component placement, top side (left) and bottom side (right)

SWRU050 Page 10 of 35

Schematic

Autres manuels pour Chipcon Products CC2400DK

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments TDP0604 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67681 Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink MSP432E4 Manuel du produit

Texas Instruments

Texas Instruments AFE79 Series Manuel utilisateur

Texas Instruments

Texas Instruments CC3235MODSF SimpleLink Manuel utilisateur

Texas Instruments

Texas Instruments TPS65941120-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67481 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430G2533 Manuel utilisateur

Texas Instruments

Texas Instruments AM243x Manuel utilisateur

Texas Instruments

Texas Instruments TMS570LS31 HDK Manuel utilisateur

Texas Instruments

Texas Instruments AFE722 Series Manuel utilisateur

Texas Instruments

Texas Instruments CC2540 Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430FR5994 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6735A Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad LP-EM-CC2340R5 Manuel utilisateur

Texas Instruments

Texas Instruments LM26EVM Manuel utilisateur

Texas Instruments

Texas Instruments MSP-FET430 Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67461 Manuel utilisateur

Texas Instruments

Texas Instruments LP-EM-CC1354P10-1 Manuel

Texas Instruments

Texas Instruments MSP430F6720 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

Texas Instruments

Texas Instruments J721EXENETXPANEVM Manuel utilisateur

Texas Instruments

Texas Instruments Errata MSP430F6779 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur