Texas Instruments UCC25600EVM Manuel utilisateur

Using the UCC25600EVM

User's Guide

Literature Number: SLUU361A

April 2009–Revised November 2018

2SLUU361A–April 2009–Revised November 2018

Submit Documentation Feedback

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

User's Guide

SLUU361A–April 2009–Revised November 2018

LLC Resonant Half-Bridge Converter,

300-W Evaluation Module

1 Introduction

The UCC25600 evaluation module, EVM (HPA341), is a 300-W LLC resonant half-bridge converter,

providing a regulated output voltage nominally at 12 V at maximum 300 W of load power with reinforced

isolation of AC-DC off-line application between the primary and the secondary, operating from a DC

source of 390 V. The EVM uses the UCC25600 resonant half-bridge controller which integrates built-in

state of the art efficiency boost features with high level protection features to provide cost effective

solutions for LLC resonant half-bridge converter applications. The secondary side uses two daughter

cards, HPA410, with diodes to make rectification.

Proper precautions must be taken when working with the EVM. High voltage levels, over 390 V, and

temperature higher than 70°C are present on the EVM when it is powered on and after power off for a

short time as well. Forced air cooling is required when the EVM is powered on.

2 Description

2.1 Typical Applications

LLC resonant half-bridge converters are seen in applications such as TVs. The converters produce higher

power conversion efficiency from their zero-voltage switching. Such converters are intended to extend to

low-voltage applications such as ATX12 power supplies for computers and servers to obtain better energy

conservation and savings. The EVM provides a platform to evaluate UCC25600 LLC resonant controller

from a PFC input voltage and 12-V output rated at 300-W output power.

2.2 Features

The UCC25600EVM, HPA341, features:

• 300-W Output Power Rating

• High Efficiency 92% Peak and Over 91% at Full Load

• Regulated Output Nominal of 12 V

• Input DC Voltage of 390 V

• Plenty of Test Points to Facilitate the Device Evaluation

• Over-Current Protection

• Output Over-Voltage Protection

• Burst Operation at Light Load

www.ti.com

Electrical Performance Specifications

SLUU361A–April 2009–Revised November 2018

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

3 Electrical Performance Specifications

(1) The EVM output may present saw-tooth waveforms or a voltage higher than the regulation point typically about 13.1 V

depending on load levels and the speed when the load is reduced. The saw-tooth waveform is caused by UCC25600 burst

operation. The output voltage of 13.1 V is caused by output over voltage protection.

Table 1. UCC25600EVM Electrical Performance Specifications

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

Input Characteristics

Voltage range VIN 375 390 405 VDC

Maximum input current VIN = 390 VDC , IOUT = 25A 0.88 A

Switching frequency VIN = 390 VDC , IOUT = 25A 110 kHz

Output Characteristics

Output voltage VOUT VIN: 390 VDC , IOUT: 1A 11.9 12 12.2 VDC

Load current1(1) VIN: 390 VDC 0 25 A

Continuous output power VIN: 390 VDC 300 W

Line regulation VIN: 375 VDC to 405 VDC , IOUT = 1.0A 5 mV

Load regulation VIN: 390 VDC , IOUT: 1 - 25A 50

Load starting burst(1) VIN: 390 VDC 0.5 A

Ripple and noise (20 MHz BW) VIN: 390 VDC , IOUT = 25A 120 mVpk-pk

Over current threshold, Io_ocp VIN: 390 VDC 30 A

Max power limit VIN: 390 VDC 350 W

Efficiency

Peak VIN = 390 VDC , IOUT = 15 A 92.5%

Full load VIN = 390 VDC , IOUT = 25 A 91%

Operation ambient temperature Full load, forced air cooling 400 LFM 45 °C

Schematic

www.ti.com

4SLUU361A–April 2009–Revised November 2018

Submit Documentation Feedback

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

4 Schematic

Figure 1. UCC25600EVM Schematic

5 Test Setup

5.1 List of Test Points

The EVM provides plenty of test points to facilitate the device's evaluation work. All test points are divided

into two major groups – primary test points and secondary test points. Their locations are shown in

Figure 2. The list below helps users to identify the functions of each test point.

www.ti.com

Test Setup

SLUU361A–April 2009–Revised November 2018

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

Figure 2. Test Point Location

Test Setup

www.ti.com

6SLUU361A–April 2009–Revised November 2018

Submit Documentation Feedback

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

Table 2 shown below lists the functions of each test point.

Table 2. UCC25600EVM Test Points

PRIMARY TEST POINTS SECONDARY TEST POINTS

NAME REF DES CONNECTION NAME REF DES CONNECTION

Vin TP1 Module input

voltage + Vxm TP7 T2 pin 12

PGND TP3 Module input

voltage - Vxm TP12 T2 pin 7

Vbias TP20 Primary Bias 12V + VOUT TP9 T2 pin 9 & 10

GND TP23 Primary Bias 12V - VO+ TP10 Output +

SS TP26 UCC25600 SS-pin VO- TP18 Output -

VDD TP22 UCC25600 VCC-pin Loop+ TP19 Loop measure +

GD1 TP24 UCC25600 pin 8 Loop- TP21 Loop measure -

GD2 TP25 UCC25600 pin 5 VOripple TP15 Output ripple

VG5 TP4 Q5 gate

OC TP17 UCC25600 pin 3

VG6 TP11 Q6 gate

SW1 TP6 Switch node of Q5

and Q6

PGND TP16 Power GND

Icr TP2 Resonant tank

current

Vxm TP5 T2 pin 6

Vcr TP13 Resonant capacitor

voltage

OUTB TP14 T3 pin 1

OUTA TP8 T3 pin 4

5.2 Test Equipment

Voltage Source: The input source shall be a constant DC source capable of supplying 390 VDC with

minimum 1.0 ADC current rating.

Multimeters: Multimeters are used to measure the output voltage (DMM1), the input voltage (DMM3), the

output current (DMM2) and the input load current (DMM4).

Output Load: A programmable electronic load is recommended, configurable for constant current mode

and capable of sinking 0 ADC to 25 ADC from 12 VDC. The output voltage can be monitored by connecting a

DC voltmeter, DMM1 to sense pins (TP10 and TP18) shown in Figure 3. A DC current meter, DMM2, may

be inserted in series with the electronic load for accurate output current measurements. Similarly, the input

voltage can be monitored by connecting a DC voltage meter to sense pins (TP1 and TP3). The input

current can be monitored by a DC current meter too. These are shown in Figure 3.

Oscilloscope: Set the oscilloscope channel to AC coupling with 20-MHz bandwidth.

www.ti.com

Test Setup

SLUU361A–April 2009–Revised November 2018

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

5.3 Notes on Power Up and Power Down

The following steps are guidelines for power up and power down of the EVM.

1. An ESD workstation is recommended. Make sure that an ionizer is on before the EVM is removed from

the protective packaging and power is applied to the EVM. Electrostatic smock and safety glasses

should also be worn.

2. Power Up

1. Set up an air cooling fan with minimum 400 LFM or 2.0 m/s forced airflow. This airflow direction

should point to the middle of DB1 and DB2 and towards transformer T2. The cooling fan should be

on throughout the test.

2. Prior to connecting the DC input source, limit the source current 1.0 A maximum. Make sure the

DC source is initially set at 390 VDC prior to turning on. Connect the DC source to the EVM as

shown in Figure 3.

3. Connect the current meters DMM2 and DMM4 as shown in Figure 3.

4. Connect the volt meter DMM1 and DMM3 as shown in Figure 3.

5. For operation with a load, connect the electronic load to the EVM as shown in Figure 3. Set the

LOAD to constant current mode with initial value of 1.0 A. Note: if the load less than 1.0 A, the

UCC25600 may be in burst operation and the EVM output voltage may start hiccup.

6. Turn on the DC source and observe the output voltage. Its output voltage should be at nominal 12

VDC.

7. Varying the load between 1.0 A and 25 A.

3. Power Down

1. Turn off the DC source.

2. Turn off the load.

5.4 Recommended Test Setup

Figure 3. Recommended Test Set Up

Test Procedure

www.ti.com

8SLUU361A–April 2009–Revised November 2018

Submit Documentation Feedback

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

6 Test Procedure

Setup the EVM with equipment as shown in Figure 3 and following the test set up directions described in

Section 5.

6.1 Line/Load Regulation and Efficiency Measurement Procedure

Set up the load to 1.0 A and input voltage between 375 VDC and 405 VDC. Prior to turning on the power,

set up the input source current limit to 1.0 A to avoid potential damage, although the EVM has its power

limit typical 350 W. Turn on the input source. Reference test results of line and load regulation can be

found from Section 7

6.2 Output Ripple

Along with the measurement of line and load regulation, the output voltage ripple can be measured at the

same time. The method of tip-and-barrel should be used for the output voltage ripple measurement. The

EVM provides such type of test point to facilitate the measurement for the type of oscilloscopes from

Tektronix as shown in Figure 3. Reference test results of the output voltage ripple can be found in

Section 7.

6.3 Efficiency

The efficiency may be calculated based on the test data obtained from Section 6.1. To correctly measure

input and output voltage for the efficiency calculation, test points TP1 and TP2 should be used for input

voltage measurement, and test points TP10 and TP18 should be used for output voltage measurement.

Reference results of efficiency can be found in Section 7.

6.4 Bode Plots

To measure loop compensation bode plots, a sweep signal may be injected through test points TP19 and

TP21. The full system bode plots is measured with TP19 and TP21. The controller bode plots is measured

with TP21 and U3 pin 4. The modulator bode plots is measured with U3 pin4 and TP19.

6.5 Others

The EVM provides plenty of test points to facilitate the device's evaluation work. Table 2 presents a list of

test points. Users can use these test points to make measurement to the functions of their interest. The

test points are divided into two groups, namely primary side group and secondary side group. During the

measurement setup, be aware of the setup especially for different ground pick up. The EVM is designed

with 3500-V reinforced insulation between the primary and the secondary. As such there is no common

ground as reference point for the measurement to be made on both sides. In other words, each side has

its own ground to be used for measurement reference point.

65.00%

75.00%

85.00%

95.00%

1 5 10 15 20 25

Load Current A

E f f i c i e n c y

12.05

12.1

12.15

12.2

375 390 405

Input Voltage V

O u t p ut V o lt a ge V

12.000

12.020

12.040

12.060

12.080

12.100

12.120

12.140

1 5 10 15 20 25

Load Current A

O u tp u t V o l t a g e V

www.ti.com

Performance Data and Typical Characteristic Curves

SLUU361A–April 2009–Revised November 2018

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

7 Performance Data and Typical Characteristic Curves

Figure 4 through Figure 17 present typical performance curves for UCC25600EVM.

Figure 4. Line Regulation, IO= 1 A Figure 5. Load Regulation, VIN = 390 VDC

Figure 6. Typical Efficiency at VIN = 390 VDC

Figure 7. Typical Output Voltage Ripple Waveform at VIN =

390 V and IO= 15 A (TP15)

UCC25600 EVM Loop Plot (Test 2)

-60

-45

-30

-15

10 100 1000 10000 100000 1000000

Frequency (Hz)

G a i n (d B )

-180

-135

-90

-45

135

180

P h a s e ( D e g )

Gain Phase

Performance Data and Typical Characteristic Curves

www.ti.com

10 SLUU361A–April 2009–Revised November 2018

Submit Documentation Feedback

LLC Resonant Half-Bridge Converter, 300-W Evaluation Module

Figure 8. Typical Output Voltage Turn On (TP15)

Figure 9. Full System Loop Compensation (TP19 and

TP21)

Figure 10. Typical Soft-Start Waveform Figure 11. Typical Resonant Tank Current and Resonant

Capacitor Voltage

Table des matières

Autres manuels Texas Instruments Unité de contrôle

Texas Instruments

Texas Instruments TAS3208EVM-LC Manuel utilisateur

Texas Instruments

Texas Instruments BQ25750 Manuel utilisateur

Texas Instruments

Texas Instruments PCM1808EVM Manuel utilisateur

Texas Instruments

Texas Instruments LM63635EVM Manuel utilisateur

Texas Instruments

Texas Instruments TAS2559 Manuel utilisateur

Texas Instruments

Texas Instruments ADS1254 Manuel utilisateur

Texas Instruments

Texas Instruments XIO2001 Manuel utilisateur

Texas Instruments

Texas Instruments LM27341 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C3 Series Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink BoosterPack BOOSTXL-CC3120MOD Manuel utilisateur

Texas Instruments

Texas Instruments UCC28064EVM-004 Manuel utilisateur

Texas Instruments

Texas Instruments LMK00308EVM Manuel utilisateur

Texas Instruments

Texas Instruments LMX9838 Manuel utilisateur

Texas Instruments

Texas Instruments TPA6120A2RGY EVM Manuel utilisateur

Texas Instruments

Texas Instruments TUSB216EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS7A78EVM-011 Manuel utilisateur

Texas Instruments

Texas Instruments TPS55165Q1-EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS1213Q1EVM Manuel utilisateur

Texas Instruments

Texas Instruments AFE79 Series Instructions de montage

Texas Instruments

Texas Instruments DRV2605LEVM-MD Manuel utilisateur

Texas Instruments

Texas Instruments AWR1443 Manuel utilisateur

Texas Instruments

Texas Instruments ADC12DL 00 Series Manuel utilisateur

Texas Instruments

Texas Instruments TPS65720EVM Manuel utilisateur

Texas Instruments

Texas Instruments TCA8424 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur