Texas Instruments LM74700DDFEVM Manuel utilisateur

User’s Guide

LM74700DDFEVM: Evaluation Module for LM74700-Q1

ABSTRACT

This user’s guide describes the evaluation module (EVM) for Texas Instruments ideal diode controller, LM74700-

Q1. This document provides configuration information and test setup details for evaluating LM74700-Q1 device

in 8-pin DDF package. An EVM schematic, board layout images, and bill of materials (BOM) are included.

Table of Contents

1 Introduction.............................................................................................................................................................................2

2 Setup........................................................................................................................................................................................2

2.1 I/O Connector Description..................................................................................................................................................2

2.2 Board Setup....................................................................................................................................................................... 3

2.3 Schematic.......................................................................................................................................................................... 4

3 Operation.................................................................................................................................................................................5

3.1 Reverse Polarity Protection................................................................................................................................................5

3.2 ORing Application.............................................................................................................................................................. 6

4 EVM Board Assembly Drawings and Layout Guidelines....................................................................................................7

4.1 PCB Drawings....................................................................................................................................................................7

4.2 Bill of Materials...................................................................................................................................................................9

List of Figures

Figure 2-1. LM74700DDFEVM Typical Application Circuit.......................................................................................................... 2

Figure 2-2. LM74700DDFEVM.................................................................................................................................................... 3

Figure 2-3. LM74700DDFEVM Schematic.................................................................................................................................. 4

Figure 3-1. Reverse Polarity 12 V to –12 V................................................................................................................................. 5

Figure 3-2. Startup Reverse Polarity (–12 V)...............................................................................................................................5

Figure 3-3. ORing Application – Higher Supply Switchover........................................................................................................ 6

Figure 3-4. ORing Application 12-V – Lower Supply Test............................................................................................................6

Figure 4-1. LM74700DDFEVM Top Side Placement................................................................................................................... 7

Figure 4-2. LM74700DDFEVM Bottom Side Placement..............................................................................................................7

Figure 4-3. LM74700DDFEVM Top Layer Routing...................................................................................................................... 8

Figure 4-4. LM74700DDFEVM Bottom Layer Routing................................................................................................................ 8

List of Tables

Table 4-1. Bill of Materials............................................................................................................................................................9

Trademarks

All trademarks are the property of their respective owners.

www.ti.com Table of Contents

SNOU177 – DECEMBER 2020

Submit Document Feedback

LM74700DDFEVM: Evaluation Module for LM74700-Q1 1

1 Introduction

The LM74700-Q1 evaluation module (LM74700DDFEVM) assists designers to evaluate the operation and

performance of the LM74700-Q1 ideal diode controller (8-pin DDF package). This evaluation module

demonstrates how an N-channel power MOSFET can emulate a very-low forward voltage diode with low IQ and

low-leakage current flowing through the IC. In this design scheme, the LM74700-Q1 is combined with a

MOSFET and used in series with a battery as a replacement for a Schottky diode and PFET, in reverse-polarity

protection circuitry as shown in Figure 2-1. For more information on the LM74700-Q1 functional and electrical

characteristics, see LM74700-Q1 Low IQ reverse battery protection ideal diode controller.

2 Setup

This section describes the jumpers and connectors on the EVM, and how to properly connect, setup, and use

the LM74700DDFEVM. Ensure the power supply is turned off while making connections on the board.

2.1 I/O Connector Description

VIN J1: Power input connector to the positive rail of the input power supply

GND1 J3: Ground connection for the power supply

VOUT J2: Power output connector to the positive side of the load

GND2 J4: Ground connection for the load

Test Points VIN, VOUT, GND1, and GND2 are test points

LM74700

GATE CATHODE

ANODE

VCAP GND

VBAT

TVS

Voltage

Regulator

Figure 2-1. LM74700DDFEVM Typical Application Circuit

Introduction www.ti.com

2LM74700DDFEVM: Evaluation Module for LM74700-Q1 SNOU177 – DECEMBER 2020

Submit Document Feedback

2.2 Board Setup

Before applying power to the LM74700DDFEVM, verify all external connections. Turn off external power supplies

and connect them with the proper polarity to the VIN and GND1 connectors. An electronic or resistive load must

be connected at the output VOUT and GND2 connectors. The tests outlined in this document are conducted with

3-A constant current as the load and 12 V at the input. Make sure that the external power-supply source for the

input voltage is capable of providing enough current to the output load so that the output voltage can be

obtained.

When all connections to the LM74700DDFEVM are verified, apply power to VIN. Figure 2-2 captures EVM board

setup.

Figure 2-2. LM74700DDFEVM

www.ti.com Setup

SNOU177 – DECEMBER 2020

Submit Document Feedback

LM74700DDFEVM: Evaluation Module for LM74700-Q1 3

2.3 Schematic

Figure 2-3 illustrates the EVM schematic.

Figure 2-3. LM74700DDFEVM Schematic

Setup www.ti.com

4LM74700DDFEVM: Evaluation Module for LM74700-Q1 SNOU177 – DECEMBER 2020

Submit Document Feedback

3 Operation

3.1 Reverse Polarity Protection

A dynamic voltage pulse from 12 V to –12 V is applied at the input of the LM74700DDFEVM. Figure 3-1 shows

the input voltage (CH1) drops down to –12 V and the output voltage (CH2) does not go negative. Therefore, the

load is protected from dynamic reverse pulses at the input. The LM74700-Q1 reacts to the negative voltage

within 2 μs and it shuts down the MOSFET by pulling the gate (CH3) voltage down. The output slowly decays

due to the large output capacitors and increased time constant.

Figure 3-1. Reverse Polarity 12 V to –12 V

A –12-V source is connected to the VIN input of the LM74700DDFEVM. Figure 3-2 shows that the output voltage

remains at a constant 0 V in this situation. This test simulates the event of connecting a 12-V battery in the

reverse direction; therefore, protecting the load from negative input voltages.

Figure 3-2. Startup Reverse Polarity (–12 V)

www.ti.com Operation

SNOU177 – DECEMBER 2020

Submit Document Feedback

LM74700DDFEVM: Evaluation Module for LM74700-Q1 5

3.2 ORing Application

When using the LM74700-Q1 as an ORing device, if the input supplies operate at slightly different voltages, the

voltage at the common load point will follow the higher voltage. The LM74700-Q1 prevents reverse current flow

from the common load point to the lower voltage supply rail. This test uses two LM74700DDFEVMs with 15 V at

the input of the first EVM and 12 V at the input of the second EVM and the output of both the EVMs are shorted.

As Figure 3-3 shows, the 15-V source at EVM1 is turned off for a period of time and the output (CH2) drops to

12-V source from EVM2. When the 15-V source is turned on again, the output rises to 15 V from EVM1. CH1

shows the input to EVM1, CH2 shows the output and CH3 shows input of EVM2.

Figure 3-3. ORing Application – Higher Supply Switchover

Next, the 12-V source at EVM2 is turned off for a period of time and turned on again, the output (CH2) does not

change. Figure 3-4 captures this test.

Figure 3-4. ORing Application 12-V – Lower Supply Test

Operation www.ti.com

6LM74700DDFEVM: Evaluation Module for LM74700-Q1 SNOU177 – DECEMBER 2020

Submit Document Feedback

4 EVM Board Assembly Drawings and Layout Guidelines

4.1 PCB Drawings

Figure 4-1 through Figure 4-4 show component placement and layout of this EVM.

Figure 4-1. LM74700DDFEVM Top Side Placement

Figure 4-2. LM74700DDFEVM Bottom Side Placement

www.ti.com EVM Board Assembly Drawings and Layout Guidelines

SNOU177 – DECEMBER 2020

Submit Document Feedback

LM74700DDFEVM: Evaluation Module for LM74700-Q1 7

Figure 4-3. LM74700DDFEVM Top Layer Routing

Figure 4-4. LM74700DDFEVM Bottom Layer Routing

EVM Board Assembly Drawings and Layout Guidelines www.ti.com

8LM74700DDFEVM: Evaluation Module for LM74700-Q1 SNOU177 – DECEMBER 2020

Submit Document Feedback

4.2 Bill of Materials

Section 4.2 lists the LM74700DDFEVM BOM.

Table 4-1. Bill of Materials

Fitted Description Designator Part Number QTY Manufacturer Package Reference Value

Fitted CAP, CERM, 1 µF, 25 V,+/- 10%, X7R,

AEC-Q200 Grade 1, 0603

C1 CGA3E1X7R1E105K080AD 1 TDK 0603 1 uF

Fitted CAP, CERM, 2.2 uF, 100 V, +/- 10%, X7R,

1210

C2 C1210C225K1RACTU 1 Kemet 1210 2.2 uF

Fitted CAP, AL, 220 µF, 63 V, +/- 20%, 0.16

ohm, AEC-Q200 Grade 2, SMD

C3 EEV-FK1J221Q 1 Panasonic SMT Radial H13 220 uF

Fitted CAP, CERM, 0.33 µF, 50 V,+/- 10%, X8R,

AEC-Q200 Grade 0, 1206

C4, C5 CGA5L2X8R1H334K160AA 2 TDK 1206 0.33 uF

Fitted Diode, TVS, Bi, 33 V, SMB D1 SMBJ33CA-13-F 1 Diodes Inc. SMB 33 V

Fitted Test Point, Miniature, SMT EN, GATE, VIN,

VOUT

5015 4 Keystone Testpoint_Keystone_Mi

niature

Fitted TEST POINT SLOTTED .118", TH GND1, GND2 1040 2 Keystone Test point, TH Slot Test

point

Fitted Machine Screw, Round, #4-40 x 1/4,

Nylon, Philips panhead

H1, H2, H3, H4 NY PMS 440 0025 PH 4 B&F Fastener Supply Screw

Fitted Standoff, Hex, 0.5"L #4-40 Nylon H5, H6, H7, H8 1902C 4 Keystone Standoff

Fitted Standard Banana Jack, Uninsulated,

8.9mm

J1, J2, J3, J4 575-8 4 Keystone Keystone575-8

Fitted MOSFET, N-CH, 60 V, 15 A, AEC-Q101,

8-PowerVDFN

Q1 DMT6007LFG-13 1 Diodes Inc. 8-PowerVDFN 60 V

Fitted RES, 0, 5%, 0.1 W, AEC-Q200 Grade 0,

0603

R1 CRCW06030000Z0EA 1 Vishay-Dale 0603 0

Fitted IC, Ideal Didoe U1 LM74700QDDFRQ1 1 Texas Instruments SOT23-8

Not Fitted Diode, TVS, Uni, 58 V, SMA D2 SMAJ58A 0 Diodes Inc. SMA 58 V

Not Fitted Diode, TVS, Uni, 58 V, 93.6 Vc, SMB D3 SMBJ58A-13-F 0 Diodes Inc. SMB 58 V

Not Fitted Diode, TVS, Uni, 24 V, 38.9 Vc, SMB D4 SMBJ24A-13-F 0 Diodes Inc. SMB 24 V

Not Fitted Fiducial mark. There is nothing to buy or

mount.

FID1, FID2, FID3,

FID4, FID5, FID6

N/A 0 N/A N/A

Not Fitted MOSFET, N-CH, 60 V, 17.9 A, AEC-

Q101, 8-PowerTDFN

Q2 DMT6005LPS-13 0 Diodes Inc. 8-PowerTDFN 60 V

www.ti.com EVM Board Assembly Drawings and Layout Guidelines

SNOU177 – DECEMBER 2020

Submit Document Feedback

LM74700DDFEVM: Evaluation Module for LM74700-Q1 9

STANDARD TERMS FOR EVALUATION MODULES

1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or

documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance

with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.

1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility

evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not

finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For

clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions

set forth herein but rather shall be subject to the applicable terms that accompany such Software

1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,

or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production

system.

2Limited Warranty and Related Remedies/Disclaimers:

2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License

Agreement.

2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM

to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by

neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have

been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications

or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control

techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.

User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)

business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.

2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit

User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty

period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or

replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be

warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day

warranty period.

WARNING

Evaluation Kits are intended solely for use by technically qualified,

professional electronics experts who are familiar with the dangers

and application risks associated with handling electrical mechanical

components, systems, and subsystems.

User shall operate the Evaluation Kit within TI’s recommended

guidelines and any applicable legal or environmental requirements

as well as reasonable and customary safeguards. Failure to set up

and/or operate the Evaluation Kit within TI’s recommended

guidelines may result in personal injury or death or property

damage. Proper set up entails following TI’s instructions for

electrical ratings of interface circuits such as input, output and

electrical loads.

NOTE:

EXPOSURE TO ELECTROSTATIC DISCHARGE (ESD) MAY CAUSE DEGREDATION OR FAILURE OF THE EVALUATION

KIT; TI RECOMMENDS STORAGE OF THE EVALUATION KIT IN A PROTECTIVE ESD BAG.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Unité de contrôle

Texas Instruments

Texas Instruments TWL6032 Manuel utilisateur

Texas Instruments

Texas Instruments TPS7A8300EVM-209 Manuel utilisateur

Texas Instruments

Texas Instruments LMH9235RRL-EVM Manuel utilisateur

Texas Instruments

Texas Instruments TRF7960A Manuel utilisateur

Texas Instruments

Texas Instruments TPS2480 EVM Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOST-IR Manuel utilisateur

Texas Instruments

Texas Instruments LMP92066 Manuel utilisateur

Texas Instruments

Texas Instruments ADS42JB46 Manuel utilisateur

Texas Instruments

Texas Instruments WL1835MODCOM8B Manuel utilisateur

Texas Instruments

Texas Instruments BOOST-DRV8711 Manuel utilisateur

Texas Instruments

Texas Instruments TPS40200 Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink BoosterPack BOOSTXL-CC3120MOD Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS1119 Manuel utilisateur

Texas Instruments

Texas Instruments TCA7408EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS6227xEVM-306 Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink CC3220MOD Series Manuel utilisateur

Texas Instruments

Texas Instruments OPT8241-CDK-EVM Manuel utilisateur

Texas Instruments

Texas Instruments ADS1x15V2EVM-PDK Manuel utilisateur

Texas Instruments

Texas Instruments CC256xEM Manuel utilisateur

Texas Instruments

Texas Instruments LM27341 Manuel utilisateur

Texas Instruments

Texas Instruments TPS2398EBM Manuel utilisateur

Texas Instruments

Texas Instruments ADS1x7xEVM-PDK Manuel utilisateur

Texas Instruments

Texas Instruments CDCE 9 Series Manuel utilisateur

Texas Instruments

Texas Instruments TPS53119EVM-690 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur