Terex MAC 25-4 SL Manuel utilisateur

25t FRANNA Superlift Crane –Ancillary Equipment

Ancillary Equipment

Brick Cage Materials Cage Sully box

Pallet Forks Dog Box Machinery Head Hook

Terex Australia Pty. Ltd.

ABN : 86 010 671 048

E-Mail : info@terex.com.au

MODEL MAC 25-4 SL

RATED CAPACITY MANUAL

Book Part Number: T139154D

HYDRAULIC MOBILE ARTICULATED PICK & CARRY CRANE

25 tonne MAXIMUM RATED CAPACITY

16.6 tonne REAR AXLE WEIGHT

Do not operate this crane unless you have read

and understood the information in this book.

CONTENTS

WARNINGS............................................................................................. 3

OPERATIONAL NOTICE .......................................................................................3

ATTACHMENT NOTICE ........................................................................................3

DEFINITIONS ..........................................................................................4

SPECIAL PRECAUTIONS FOR ARTICULATED CRANES ....................5

GENERAL ...................................................................................................5

SET-UP ...................................................................................................5

OPERATION ...................................................................................................6

LIFT AND CARRY OPERATION............................................................................7

OPERATION ON SIDE SLOPES.............................................................8

SPECIFICATIONS...................................................................................9

CRANE CONFIGURATION ...................................................................11

RATED CAPACITY CHARTS................................................................12

001: NO COUNTERWEIGHT –WINCH...............................................................13

101: FRONT COUNTERWEIGHT - WINCH.........................................................14

102: FRONT COUNTERWEIGHT - RHINO HOOK..............................................15

105: FRONT COUNTERWEIGHT - FLYJIB (3m) - 0OOFFSET ..........................16

106: FRONT COUNTERWEIGHT - FLYJIB (3m) - 12.5OOFFSET......................16

109: FRONT COUNTERWEIGHT - MANBASKET...............................................17

110: FRONT COUNTERWEIGHT - FIXED LUG..................................................17

111: FRONT COUNTERWEIGHT - INNER LUG (L1)..........................................18

112: FRONT COUNTERWEIGHT - OUTER LUG (L2) ........................................19

201: REAR COUNTERWEIGHT - WINCH...........................................................20

202: REAR COUNTERWEIGHT - RHINO HOOK................................................21

205: REAR COUNTERWEIGHT - FLYJIB (3m) - 0OOFFSET.............................22

206: REAR COUNTERWEIGHT - FLYJIB (3m) - 12.5OOFFSET........................22

209: REAR COUNTERWEIGHT - MANBASKET.................................................23

210: REAR COUNTERWEIGHT - FIXED LUG ....................................................23

211: REAR COUNTERWEIGHT - INNER LUG (L1) ............................................24

212: REAR COUNTERWEIGHT - OUTER LUG (L2)...........................................25

301: REAR SL COUNTERWEIGHT - WINCH......................................................26

302: REAR SL COUNTERWEIGHT - RHINO HOOK...........................................27

305: REAR SL COUNTERWEIGHT - FLYJIB (3m) –0OOFFSET.......................28

306: REAR SL COUNTERWEIGHT - FLYJIB (3m) –12.5OOFFSET.................28

309: REAR SL COUNTERWEIGHT - MANBASKET............................................29

310: REAR SL COUNTERWEIGHT - FIXED LUG...............................................29

311: REAR SL COUNTERWEIGHT - INNER LUG (L1).......................................30

312: REAR SL COUNTERWEIGHT - OUTER LUG (L2) .....................................31

AFTERMARKET CONTACTS LIST....................................................... 32

NOTE: ALL PAGES MUST BE INCLUDED IN THIS BOOK.

T139154-D

WARNINGS

OPERATIONAL NOTICE

IMPROPER CRANE USE, CARE OR OPERATION

CAN CAUSE INJURY, DEATH OR PROPERTY

DAMAGE.

DO NOT OPERATE THIS MACHINE UNLESS YOU

HAVE READ AND UNDERSTAND THE OPERATOR’S

MANUAL AND CRANE RATED CAPACITY MANUAL.

COPIES OF OPERATOR’S MANUALS AND CRANE RATED CAPACITY

MANUAL MAY BE OBTAINED FROM:

ATTACHMENT NOTICE

WRITTEN AUTHORISATION IS REQUIRED FROM

TEREX AUSTRALIA PTY LTD PRIOR TO THE USE OF

ANY ATTACHMENT NOT SPECIFIED IN THE MANUAL.

T139154-D

DEFINITIONS

Articulation – The crane pivots in the middle to allow steering and slewing of the

load. Up to 40Articulation is possible in either direction. See Working Area diagram

Deration – A decrease in the Rated Capacity due to external influences, expressed as

a percentage.

Freely Suspended Load – Load hanging free with no direct external force applied

except by the winch rope.

Gradient: Generalised slope of ground measured as a percentage.

Load Radius –The horizontal distance from the centre of the freely suspended

hoisting hook perpendicular to a vertical plane containing the front axle.

Loaded Boom Angle – This is given to assist in setting up the crane only. It gives

only an approximation of the Load Radius for a specified boom length. “Boom Angle”

on Rated Capacity charts refers to the angle between the boom and true horizontal.

(Refer to image below)

Load Moment Indicator (LMI) - A system that displays rated capacity for the given

configuration. An audible warning sounds when rated capacity is approached and

reached.

Pitch Angle – The forward tilt

of the crane, the angle

between the chassis of the

front of the crane and true

horizontal in the longitudinal

direction. The pitch is positive

when the front is higher than

the rear. In the image shown,

the pitch angle is negative.

Rated Capacity (RC) – The total Freely Suspended Load, including the mass of

material and load handling equipment, that the machine can safely lift under ideal

conditions at a given configuration.

Roll – The side tilt of the crane chassis, the angle

between the front chassis of the crane and true

horizontal. The roll angle is positive when the left side

of the crane is higher than the right side. In the image

shown, which is a view on the front of the crane, the roll

angle is negative.

Side Load – Any external force applied either to the

boom or load in a horizontal direction.

Slope: Generalised angle of the ground measured in

degrees.

Tilt: Generalised combination of pitch and roll.

Work Areas – Area measured in an arc about the centre pivot as shown on the

Working Area diagram.

T139154-D

SPECIAL PRECAUTIONS FOR ARTICULATED CRANES

THERE IS A POTENTIAL FOR CRUSHING BETWEEN FRONT AND REAR

CHASSIS WHEN THE MACHINE ARTICULATES. NEVER STAND IN THE PIVOT

AREA WHEN THE ENGINE IS RUNNING OR EMERGENCY STEERING PUMP IS

OPERATING. ALWAYS REMOVE THE KEY FROM THE IGNITION BEFORE

WORKING IN THE PIVOT AREA.

DO NOT LEAVE IGNITION KEY SWITCHED ON WITH ENGINE STOPPED AND

PARK BRAKE OFF, AS EMERGENCY HYDRAULIC STEERING PUMP WILL

ACTIVATE.

GENERAL

1. This machine has been designed to meet the requirements of AS1418.1 (2002)

& 1418.5 (2002) and has been tested in accordance with these standards for

pick and carry operation on tyres. The machine classification is C3.

2. Rated Capacities shown are for this machine as originally manufactured by

Terex Australia Pty Ltd. The Rated Capacities only apply when all the

instructions in this book are rigidly followed. Modifications to this machine or

use of equipment other than that specified can result in a reduction in Rated

Capacity.

3. If improperly operated or maintained, this machine can be hazardous.

Operation and maintenance of this machine must be in compliance with the

information documented in this rated capacity manual and in the operators,

service and parts manuals furnished. If these manuals are missing, obtain

replacements through Terex Australia Pty Ltd or their agents.

SET-UP

4. Reduced crane Rated Capacities for the particular job shall be established, by

the operator, with due allowance for adverse operating conditions. These

conditions include the supporting surface, pendulum action of the load, jerking

or sudden stops of the load and other factors affecting stability, two machine

lifts, electrical wires, adverse weather, wind, hazardous surroundings,

experience of personnel, etc.

5. Rated Capacity is based on Freely Suspended Loads. Lifting, or travelling with

a load, on soft or uneven ground can be hazardous and will reduce the Rated

Capacity of the crane. Refer to the section “Operation on Slope” for further

information.

6. No attempt shall be made to drag the load along the ground in any direction.

7. Wind forces on the boom, resulting from winds up to 10 m/s (36 km/h), are

incorporated in the Rated Capacity. Any additional Side Loading due to wind

forces on the load will reduce the Rated Capacity, and must be considered.

8. Rated Capacities include the mass of hooks, blocks, slings and auxiliary lifting

devices. Their mass must be subtracted, from the listed Rated Capacity, to

determine the equivalent net load.

T139154-D

9. Loaded Boom Angles at specified boom lengths give only an approximation of

the Load Radius. The Boom Angle before loading should be greater to account

for boom deflection increasing the Load Radius as the load is lifted.

OPERATION

10. Read and understand all warnings and instructional notes.

11. Do not tip the machine to determine allowable lifting capacities.

12. Loads may be lifted from:

The main boom head on the winch.

The rhino hook.

The fixed lug.

Either of the two sliding lugs on the boom.

A flyjib is also available to extend the maximum boom length

A “manbasket” can be pinned to the head of the boom.

Always use the correct Rated Capacity chart for the lifting point in use, and the

position of the counterweight. Ensure the LMI is set to the correct duty.

NOTE : Written authorisation from Terex Australia Pty Ltd is required

prior to the use of any attachment not specified in the manual.

13. “Crane mode” can only be engaged when “low range” is selected. Selecting

“crane mode” will cause the front suspension lockouts to engage.

14. Lifting from more than one lifting point simultaneously is neither intended nor

approved.

15. Handling of personnel from the boom is neither intended nor approved, except

in a Terex Australia Pty Ltd supplied manbasket, correctly installed on the head

of the boom, or other approved arrangement.

16. When either the boom length or Load Radius or both are between values listed,

the smallest load shown at either the next larger Load Radius or boom length

shall be used, or the interpolated value shown on the LMI may be used.

17. Side Loading of the machine and load swing out may cause structural failure or

machine tip-over. Side Loads may be generated by:

Lifting when not level.

Sudden acceleration or deceleration

Sudden movement when articulating with a load.

Dragging a load.

Pushing a load.

Wind forces on load and boom structure.

18. It is safe to attempt to telescope any load within the limits of the Rated Capacity

Manual. The maximum load that may be telescoped is limited by hydraulic

pressure, Loaded Boom Angle and powered boom sections lubrication.

T139154-D

19. Boom extension 1 and boom extension 2 move simultaneously. The winch

rope is fully compensated for boom extension when boom extensions 1 & 2 are

being telescoped. Boom extension 3 is powered on the MAC 25 however there

is no compensation of the winch rope as the third extension is being extended.

Operator to take care to extend rope as required while boom extension 3 is

being telescoped.

20. Do not allow the winch rope to unwind fully. Always ensure a minimum of

2 wraps of rope remain on the winch drum.

21. Rated Capacity depends on tyre rating, tyre condition and tyre inflation

pressure. All tyres must be in good condition and must be inflated to the

recommended pressure before attempting a lift.

22. Pick & carry operation is permitted through the full Articulation range, however,

Rated Capacity is reduced when articulating. On the series 4 MAC 25, the LMI

dynamically calculates rated capacity taking crane tilt and articulation into

account.

23. The maximum speed for pick & carry operation is 0.4m/s (1.44km/h). The

transfer case shall be set to low range.

24. Operation of this crane in excess of the Rated Capacity and disregard of the

instructions is hazardous.

LIFT AND CARRY OPERATION

Observe the following during travel with load on the crane:

Keep the boom tip as close to the ground as possible by using:

The MINIMUM practical boom length

The MINIMUM practical Boom Angle.

Keep the load as CLOSE to the ground as possible.

Keep the load as CLOSE to the front of crane as possible

Use the MINIMUM Articulation angle practical - REMEMBER the crane will side tilt

when articulated and hence the hook will move towards the direction of Articulation

whilst steering.

Load swing greatly reduces stability – REMEMBER to tagline loads to prevent

pendulum motion of the load. Travel and crane motions should be applied gently

to minimise this effect.

Always REMEMBER:

On flat ground - Increased articulation reduces load capacity

On sloping ground – Downhill articulation reduces load capacity.

T139154-D

OPERATION ON SLOPE

The operation on slope of cranes that travel with a freely suspended loads should be

avoided if at all possible (refer to AS 2550.5). Mobile Cranes are primarily designed to

operate on firm, flat, level ground - within a 1% gradient (refer to AS 1418.5 (2002)).

Any deviation from this requires that the Rated Capacity shall be reduced (derated)

accordingly.

If it is necessary to operate on slope the

precautions listed below must be taken.

REMEMBER that surface depressions and

potholes will create the same effect as a

sloping surface.

Ensure the ground condition is FIRM

enough to support the axle loads.

Ensure the tyres are inflated to the correct

operating pressures.

Keep the load on the UPHILL side of the

crane where possible. REMEMBER the

working Load Radius will increase if the

load is suspended in the downhill position.

NOTE:

The MAC 25 crane must at no time be

operated on a slope greater than

5(8.75% gradient).

In order to determine the slide slope of a

particular site the crane’s LMI can be used to

give an approximation. Before commencing

the lift, drive the un-laden crane slowly across

the sloping surface and note the maximum

slope displayed. Take the reading when the

crane’s articulation is zero (straight ahead)

and with the boom (fully retracted) in its

lowest position practical.

The MAC 25 is fitted with an LMI that

calculates the rated capacity for the crane

when the crane tilts in any direction.

SLOPE RATED CAPACITY

The degree of tilt of the front body results from a number of factors. Articulation of the

crane induces tilt as does working on a slope. In combination the body tilt is

increased when the load is on the DOWNHILL side of the crane (when the crane

articulation direction is down a side slope).

T139154-D

The degree of tilt of the front body and boom is further increased by the deflection of

the tyres. This is illustrated in Figure 1. For instance, a 5Oground side slope may

result in chassis tilt of say 7O.

The LMI determines and displays the degree of body tilt measured by a sensor that is

attached to the front body. This sensor measures the angle of the front body, not the

angle of slope of the ground. When the crane is un-laden, the boom fully down, and

the crane is at zero articulation, the body will be close to the same angle as the

ground, for up to 5o slope.

This body tilt angle (the “Roll”) is used by the LMI to derate the crane as this is also

the angle the boom has been tilted sideways. When lifting or carrying a load in slope

situations, the tilt of the body will change as the weight of load is taken by the crane.

In most circumstances, this change will be further derate the crane. Hence in planning

a lift, it is important to be conservative on lift capacity in any circumstance where the

lift will induce significant front body tilt.

SPECIFICATIONS

ATTACHMENT MASSES

Single part hook block PL16M2090 30 kg

Four/six part hook block PLMXA3033 230 kg

Rhino Hook PLMXF3015 25 kg

9 tonne hook PP2190200 10 kg

25 tonne hook PP2087500 26 kg

12 tonne spreader bar PL16A3035 94 kg

15 tonne spreader bar PL15A8023 107 kg

Adapter - Flyjib & Manbasket PLMXF3018 25 kg

Flyjib (3m) PL16A3056 79 kg

Mount arm - Manbasket C2061 85 kg

Manbasket C2062 130 kg

NOTE : These masses apply only to Terex Australia Pty Ltd supplied

equipment.

HOOK BLOCK

Hook Block: Number of

Falls of Rope Maximum Hook

Block RC (kg)

1 4200

2 8400

4 16800

6 25000

T139154-D

Table des matières

Autres manuels Terex Système de levage

Terex

Terex Genie Z452513A-48153 Manuel d'installation et d'exploitation

Terex

Terex Genie GS-1532 Manuel d'installation et d'exploitation

Terex

Terex Genie GS -1530/32 Manuel utilisateur

Terex

Terex Genie GS-1432m Manuel utilisateur

Terex

Terex Genie GS-1530 Manuel utilisateur

Terex

Terex Genie GS-1432m Manuel d'installation et d'exploitation

Terex

Terex Genie Superlift Advantage Manuel utilisateur

Terex

Terex C5000 Series Manuel utilisateur

Terex

Terex Genie GTH4016 SR Manuel utilisateur

Terex

Terex Genie GR10-20000 Manuel utilisateur

Terex

Terex Genie GR Series Manuel utilisateur

Terex

Terex Genie Z-45 DC Manuel d'installation et d'exploitation

Terex

Terex Genie Load Lifter Manuel utilisateur

Terex

Terex SX18014-101 Manuel utilisateur

Terex

Terex Genie GR-20J Manuel utilisateur

Terex

Terex Genie SX-105 XC Manuel d'installation et d'exploitation

Terex

Terex Genie S-60 FE Manuel d'installation et d'exploitation

Terex

Terex Genie Z-45 XC Manuel d'installation et d'exploitation

Terex

Terex Genie SX-135 XC Manuel utilisateur

Terex

Terex Genie GRC-12 Guide de configuration

Terex

Terex Genie SX-105 XC Manuel utilisateur

Terex

Terex Genie Super Series Manuel utilisateur

Terex

Terex Genie SX-150 Manuel d'installation et d'exploitation

Terex

Terex Genie Lift Tools Expo Installer Z-45/25 Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur