Terex SX135D-101 Manuel utilisateur

Operator's Manual

Serial Number Range

SX™-135 XC™

from SX135H-515

with

Maintenance

Information

Original Instructions

Second Edition

Third Printing

Part No. 1301106GT

FrontMatter

from SX135D-101

Operator's Manual Second Edition • Third Printing

Introduction

SX™-135 XC™Part No. 1301106GT

Manufacturer:

Terex Global GmbH

Bleicheplatz 2

Schaffhausen, 8200

Switzerland

EU Authorized representative:

Genie Industries B.V.

Boekerman 5

4751 XK OUD GASTEL

The Netherlands

UK Authorized representative:

Genie UK Limited

The Maltings

Wharf Road

Grantham

NG31 6BH

Contents

Introduction ............................................................1

Symbol and Hazard Pictorials Definitions..............6

General Safety .......................................................9

Personal Safety................................................... 12

Work Area Safety................................................ 13

Legend ................................................................ 23

Controls............................................................... 24

Inspections.......................................................... 32

Operating Instructions......................................... 47

Transport and Lifting Instructions ....................... 63

Maintenance ....................................................... 69

Specifications...................................................... 73

Second Edition: Third Printing, September 2022

Genie is a registered trademark of Terex South Dakota, Inc. in

the U.S.A. and many other countries.

"SX" and "XC" are trademarks of Terex South Dakota, Inc.

Complies with EC Directive 2006/42/EC

See EC Declaration of Conformity

Supply of Machinery (Safety) Regulations 2008

Second Edition • Third Printing Operator's Manual

Introduction

Part No. 1301106GT SX™-135 XC™1

Intr od ucti on

About this manual

Genie appreciates your choice of our machine for

your application. Our number one priority is user

safety, which is best achieved by our joint efforts.

This book is an operation and daily maintenance

manual for the user or operator of a Genie

machine.

This manual should be considered a permanent

part of your machine and should remain with the

machine at all times. If you have any questions,

contact Genie.

Product Identification

The machine serial number is located on the serial

label.

Serial number stamped on

chassis

Serial label

(located under cover)

Intended Use and Familiarization

Guide

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site. Before operating the machine, it’s

the operator’s responsibility to read and

understand this familiarization guide.

Each person must be trained to operate a

Mobile Elevating Work Platform (MEWP).

Familiarization with the MEWP must be given

to each person who is authorized, competent

and trained.

Only trained and authorized personnel should

be permitted to operate the machine.

The operator is responsible to read,

understand, and obey the manufacturer’s

instructions and safety rules provided in the

Operator’s Manual.

The Operator’s Manual is located in the

manual storage container, at the platform.

For specific product applications, see

Contacting The Manufacturer.

Operator's Manual Second Edition • Third Printing

Introduction

2 SX™-135 XC™Part No. 1301106GT

Platform controls symbology and related

machine movement:

Platform level

Platform rotate

Jib boom up/down

Boom up/down

Boom

extend/retract

Turntable rotate

Drive forward/reverse

Steer right/left

Jib boom extend/retract

Axle extend

Axle retract

Square end steer

Circle end steer

Crab steer

Coordinated steer

Second Edition • Third Printing Operator's Manual

Introduction

Part No. 1301106GT SX™-135 XC™3

Ground controls symbology and related

machine movement:

Platform level, jib boom

up/down, boom

extend/retract,and boom

up/down

Turntable rotate and

platform rotate

Sequential functions and movement:

•Drive and steer.

Interlocked functions:

•Elevated drive speed.

•Elevated drive in an off-level condition.

•Drive enable when the boom is rotated past the

non-steer wheels, or non-steer tracks.

•All platform and ground controls.

Limitations of use:

•The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site.

•Do not elevate the platform unless the machine

is on firm level ground.

Stability enhancing means:

•X chassis

Restricted operating envelope:

•1,000 lbs/454 kg platform capacity.

Operator's Manual Second Edition • Third Printing

Introduction

4 SX™-135 XC™Part No. 1301106GT

Bulletin Distribution and

Compliance

Safety of product users is of paramount

importance to Genie. Various bulletins are used by

Genie to communicate important safety and

product information to dealers and machine

owners.

The information contained in the bulletins is tied to

specific machines using the machine model and

serial number.

Distribution of bulletins is based on the most

current owner on record along with their

associated dealer, so it is important to register

your machine and keep your contact information

up to date.

To ensure safety of personnel and the reliable

continued operation of your machine, be sure to

comply with the action indicated in a respective

bulletin.

To view any open bulletins for your machine, visit

us on the web at www.genielift.com.

Contacting the Manufacturer

At times it may be necessary to contact Genie.

When you do, be ready to supply the model

number and serial number of your machine, along

with your name and contact information. At

minimum, Genie should be contacted for:

Accident reporting

Questions regarding product applications and

safety

Standards and regulatory compliance information

Current owner updates, such as changes in

machine ownership or changes in your contact

information. See Transfer of Ownership, below.

Transfer of Machine Ownership

Taking a few minutes to update owner information

will ensure that you receive important safety,

maintenance and operating information that

applies to your machine.

Please register your machine by visiting us on the

web at www.genielift.com or by calling us toll free

at 1-800-536-1800.

Second Edition • Third Printing Operator's Manual

Introduction

Part No. 1301106GT SX™-135 XC™5

Danger

Failure to obey the instructions and

safety rules in this manual will result

in death or serious injury.

Do Not Operate Unless:

You learn and practice the principles of safe

machine operation contained in this operator’s

manual.

1 Avoid hazardous situations.

Know and understand the safety rules

before going on to the next section.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to use.

4 Inspect the workplace.

5 Only use the machine as it was intended.

You read, understand and obey the

manufacturer’s instructions and safety rules—

safety and operator’s manuals and machine

decals.

You read, understand and obey employer’s

safety rules and worksite regulations.

You read, understand and obey all applicable

governmental regulations.

You are properly trained to safely operate the

machine.

Safety Sign Maintenance

Replace any missing or damaged safety signs.

Keep operator safety in mind at all times. Use mild

soap and water to clean safety signs. Do not use

solvent-based cleaners because they may

damage the safety sign material.

Hazard Classification

Decals on this machine use symbols, color coding,

and signal words to identify the following:

Safety alert symbol

—

used to alert

you to potential personal

injury

hazards. Obey all safety

messages that follow this symbol

to avoid possible injury or death.

Indicates a hazardous situation

which, if not avoided, will result in

death or serious injury.

Indicates a hazardous situation

which, if not

avoided, could result

in death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in minor or moderate injury.

Indicates a property damage

message.

Operator's Manual Second Edition • Third Printing

Symbol and Hazard Pictorials Definitions

6 SX™-135 XC™Part No. 1301106GT

Symb ol an d H az ar d Pi ct orial s D e fi niti ons

Crushing hazard Keep away from

moving parts

Crush hazard Overhead obstruction Collision hazard

Electrocution hazard Maintain required

clearance

Tip-over hazard Tip-over hazard Tip-over hazard

Electrocution hazard Avoid contact Disconnect battery Read the operator’s

manual

Read the service

manual

Second Edition • Third Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1301106GT SX™-135 XC™7

Explosion hazard No smoking.

No flame.

Stop engine.

Explosion hazard Burn hazard Fire extinguisher

Fire hazard No smoking Explosion hazard No step Lanyard anchorage

point

Platform tie-down

instructions

Lifting, tie down instructions Tie-down point Lifting point

Wind speed Runaway hazard Weight of welder

reduces capacity

Wheel load Tire specifications

Operator's Manual Second Edition • Third Printing

Symbol and Hazard Pictorials Definitions

8 SX™-135 XC™Part No. 1301106GT

Recovery procedure if tilt alarm sounds while

elevated.

Platform uphill:

1 Lower boom.

2 Retract boom.

Platform downhill:

1 Retract boom.

2 Lower boom.

Do not use ether or

other high energy

starting aids on

machines equipped

with glow plugs.

Voltage rating for

power to platform

Pressure rating for

air line to platform

Color coded direction

arrows

Access by trained and

authorized personnel

only

Manual force Maximum capacity Crush hazard

Support the platform

or boom during

maintenance

Auxiliary lowering

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Terex Système de levage

Terex

Terex Genie Z-34/22 IC Manuel utilisateur

Terex

Terex Z3413-9461 Manuel d'installation et d'exploitation

Terex

Terex Genie GS-1432m Manuel utilisateur

Terex

Terex TA50RT Manuel utilisateur

Terex

Terex Genie Z-45/25 Bi-Energy Manuel utilisateur

Terex

Terex HP-32 Manuel utilisateur

Terex

Terex Genie GR-12 Manuel utilisateur

Terex

Terex GTH08E-11500 Manuel d'installation et d'exploitation

Terex

Terex Genie S-80 XC Series Manuel utilisateur

Terex

Terex Genie S-100 Manuel utilisateur

Terex

Terex Genie Z-60/37DC Manuel utilisateur

Terex

Terex Genie IWP Series Manuel utilisateur

Terex

Terex Genie SX-105 XC Manuel d'installation et d'exploitation

Terex

Terex Genie Z452513A-48153 Manuel d'installation et d'exploitation

Terex

Terex Genie Z-45 XC Manuel d'installation et d'exploitation

Terex

Terex Genie GR-20J Manuel utilisateur

Terex

Terex Genie GS-1530 Manuel utilisateur

Terex

Terex Genie GRC-12 Manuel utilisateur

Terex

Terex SX180H-745 Manuel utilisateur

Terex

Terex Genie GR Series Manuel utilisateur

Terex

Terex SX18014-101 Manuel utilisateur

Terex

Terex Genie S-45 Trax Manuel utilisateur

Terex

Terex Genie QS-12W Manuel utilisateur

Terex

Terex Genie GTH1215M-101 Manuel d'installation et d'exploitation

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur