Teldat H1 HSDPA Manuel utilisateur

Teldat H/L Router Family

Teldat-Dm 402-I

Teldat S.A. Manual

Teldat H/L Router Family 1

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-

ery, supply or use of this manual.

Manual Teldat S.A.

2Teldat H/L Router Family

Table of Contents

I ImportantInformation................................ 1

Chapter1 Description..................................... 2

1.1 Introduction...................................... 2

1.1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter2 Installation...................................... 5

2.1 Connections...................................... 5

2.1.1 PowerSourceConnection................................ 5

2.1.2 DataConnection.................................... 6

2.1.3 Connecting the WWAN antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1.4 Connecting the WLAN antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1.5 Connecting for configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 InstallingtheSIMcard................................. 10

2.2.1 Installing the internal SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2.2 Installing the external SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter3 MeaningoftheLEDs............................... 13

Chapter4 Microswitches................................... 15

4.1 Procedure to ignore the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter5 Appendix..................................... 17

5.1 Troubleshooting................................... 17

5.2 Softwareupdating .................................. 17

5.3 Connectors ..................................... 17

5.3.1 LANConnector.................................... 18

5.3.2 WWANConnectors.................................. 18

5.3.3 WLANConnectors.................................. 18

5.3.4 SERIALConnector.................................. 18

5.3.5 ConfigurationConnector................................ 19

5.4 TechnicalSpecifications................................ 19

5.5 Safetywarnings ................................... 21

Teldat S.A. Table of Contents

Teldat H/L Router Family i

Table of Contents Teldat S.A.

ii Teldat H/L Router Family

I Important Information

Note

The manufacturer reserves the right to make changes and improvements in the appropriate features in

either software or hardware of this product, modifying the specifications of this manual without prior no-

tice.

The images showing the front and back panels of the device are for information purposes only. Some

small modification may exist in the actual device.

The equipment is intended to be installed by Service Personnel and only handled by qualified person-

nel. If not, the device may be damaged and malfunction.

This device contains elements that are sensitive to electrostatic surges and shocks. Therefore, it is es-

sential when handling the equipment that an antistatic wristwrap is connected to the device chassis and

that this is placed on an antistatic mat. Furthermore, it is crucial to avoid any kind of contact between

the device components and necklaces, bracelets, rings, ties, etc.

Teldat S.A. Important Information

Teldat H/L Router Family 1

Chapter 1 Description

1.1 Introduction

The Teldat H/L is a general purpose IP router, suitable for a wide range of applications (SOHO/SME and corporate

environments).

It eneables the user to access data networks through cellular or mobile telephony technologies. Thanks to its modu-

lar design, the router adapts perfectly to the latest emerging technologies. The Teldat H/L is also compatible with

GPRS, EDGE, UMTS, HSDPA, HSUPA, CDMA 2000 1xRTT, CDMA Ev-Do, etc.

The Teldat H/L is suitable for plenty of IP scenarios, providing simultaneous access to the Internet for private LAN

users and accommodating teleprocess networks and SNA support. The most common applications are:

• Access router

• Backup for LAN networks

• Backup for WAN networks

Fig. 1: Access Router

Fig. 2: Backup for LAN network

The Teldat H/L covers the access needs for cellular technologies (GPRS, UMTS, HSDPA, HSUPA, etc.). Some

models may not include a 3G module (Teldat L) although this can be installed at the client’s request. The Teldat H/L

has a 4 port Ethernet LAN Switch and can be equipped with a Wireless LAN MINI-PCI module.

Certain Teldat H/L models incorporate a synchronous/asynchronous multi-purpose serial port (compatible with RS-

232, V.35, RS-485 and X.21 lines). Thanks to its maximum E1/T1 speed (2Mbps), the port provides 3G access to

standalone ATMs, WAN networks, etc.

1 Description Teldat S.A.

2Teldat H/L Router Family

Fig. 3: Standalone ATM with IP Telesurveillance

The Teldat H/L range boasts several models equipped with different cellular technology:

• Teldat H1 HSDPA

• Teldat H1 HSUPA

• Teldat H1 EV-DO

This manual shows you how to install and connect these routers.

Fig. 4: Teldat H1: External aspect

1.1.1 Recycling and the Environment

Please do not, under any circumstances, throw away any Teldat H/L with normal domestic waste. Ask your local

town hall for information on how to correctly dispose of them in order to protect the environment against e-waste. Al-

ways respect the current laws regarding waste material. Anyone found violating the environmental laws will be sub-

ject to fines and any additional steps established by law.

All the packing materials i.e. the cardboard box, plastic and any other packaging, together with the pieces making up

aTeldat H/L , must be recycled complying with the current active laws regarding recycling materials.

The symbol shown below, with a cross over the rubbish container, can be seen on the device. This means that, when

a device reaches the end of its life, it must be taken to the official recycling/disposal centers where it must be dis-

posed of in an environmentally responsible manner and separately from normal domestic waste.

Teldat S.A. 1 Description

Teldat H/L Router Family 3

1 Description Teldat S.A.

4Teldat H/L Router Family

Chapter 2 Installation

2.1 Connections

Note

BEFORE INSTALLING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-

FULLY

Workplace Conditions. Main Characteristics

• Excessive cold and heat should be avoided, as should humidity and dust.

• Avoid direct exposure to sunlight and any other heat sources. Do not place the device between papers, magazines

or other items that could hinder natural air circulation.

• Do not place the device near strong electromagnetic fields, such as those produced by speakers, motors, etc.

• Avoid knocks and/or strong vibrations during transport, operation and storage.

Warning

The electric current in power cables, telephone lines and communication cables is dangerous. To pre-

vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-

nect the cables following the steps set forth in the following section.

To Connect To Disconnect

Turn the power switch OFF. Turn the power switch OFF.

Check the power supply is not connected to the mains or

to the device.

Disconnect the power supply from the mains.

Connect all data cables. Disconnect the power supply from the device.

Connect the power supply to the device. Disconnect the data cables.

Connect the power supply to the mains.

Turn the power switch ON.

2.1.1 Power Source Connection

The Teldat H/L is powered with an external AC/DC source.

To avoid electric shocks, residual current circulation and other unwanted effects that may disrupt communication, the

following is recommended:

Warning

All interconnected communication devices should be plugged to THE SAME GROUNDED POWER

OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).

Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated

supply, or it is independent from the rest (such as lighting, etc.), it is highly recommended that

all data devices should be connected to the same power source. This will avoid operating and

premature aging problems of drivers and other components.

Teldat S.A. 2 Installation

Teldat H/L Router Family 5

Fig. 5: Power supply connection with external source

To connect the power source to the router, make sure the switch is OFF (0) and that the power supply is NOT con-

nected to the mains. Then find the 12 VDC connector (located on the rear panel) and plug it into the power source.

2.1.2 Data Connection

The Teldat H/L is equipped with following connectors (some models may not have all):

SWITCH:

The Teldat H/L incorporates a 4 port 10/100BaseT switch with automatic MDI/MDIX for local area network (LAN)

connection. In addition, the router has two connection LEDs: one indicating connection at 100 Mbps and the other at

10 Mbps.

Please pay close attention to the labelling to avoid confusing the switch with other port types.

Its availability depends on the model.

Fig. 6: LAN Switch ports (4)

SERIAL:

A multistandard serial interface to connect to an external modem (POS) or to a wide area network (WAN), such as

X.25, Frame Relay, PPP, etc. Other possibilities are also availbale.

It requires an insertable driver (V.24, V.35, V.36, X.21, RS-485) for operating purposes.

Fig. 7: SERIAL connector

CONF:

The Teldat H/L is equipped with a serial interface through a female RJ45 connector, on the front panel, known as

Conf. This provides access to the router’s local console or operates as an asynchronous serial port. The interface

behavior must be preconfigured. By default, the interface is configured in local console mode. This section only deals

with operations in asynchronous mode.

2 Installation Teldat S.A.

6Teldat H/L Router Family

Autres manuels pour H1 HSDPA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Teldat Routeur réseau

Teldat

Teldat M2 Manuel utilisateur

Teldat

Teldat Connect-4GePlus Manuel utilisateur

Teldat

Teldat RS123 Seies Manuel utilisateur

Teldat

Teldat WWAN Enabler Manuel utilisateur

Teldat

Teldat H2 RAIL Manuel utilisateur

Teldat

Teldat Teldat-3Ge Manuel utilisateur

Teldat

Teldat C+ Series Manuel utilisateur

Teldat

Teldat ATLAS 60 NW Manuel utilisateur

Teldat

Teldat Teldat V Manuel utilisateur

Teldat

Teldat H1 HSDPA Manuel utilisateur

Teldat

Teldat RS300 Series Manuel utilisateur

Teldat

Teldat Regesta-PRO ER B Manuel utilisateur

Teldat

Teldat Connect-FW Manuel utilisateur

Teldat

Teldat Regesta Lite AU Manuel utilisateur

Teldat

Teldat RXL15000 Manuel utilisateur

Teldat

Teldat SDE Manuel utilisateur

Teldat

Teldat Regesta PLC Manuel utilisateur

Teldat

Teldat Connect-FW5G Manuel utilisateur

Teldat

Teldat M1 Manuel utilisateur

Teldat

Teldat Atlas-i70 Manuel utilisateur

Teldat

Teldat Regesta Smart PLC Manuel utilisateur

Teldat

Teldat RS1800 Series Manuel utilisateur

Teldat

Teldat REGESTA-PRO-ER Series Manuel utilisateur

Teldat

Teldat M2 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité