Tektronix RSA3408A Manuel utilisateur

Service Manual

RSA3408A

8 GHz Real-Time Spectrum Analyzer

071-1691-01

This document applies to firmware version 3.20

and above.

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

Warranty 2

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year

from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either

will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the

defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or

reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction

caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other

products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER

WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’

RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY

PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL

NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY

OF SUCH DAMAGES.

RSA3408A Service Manual i

Table of Contents

General Safety Summary ix...................................

Service Safety Summary xi....................................

Preface xiii...................................................

Manual Structure xiii................................................

Manual Conventions xiv..............................................

Related Documentation xiv...........................................

Introduction xv..............................................

Performance Check Interval xv........................................

Strategy for Servicing xv.............................................

Specifications

Performance Conditions 1--1...........................................

Electrical Characteristics 1--2..........................................

Physical Characteristics 1--16...........................................

Environmental Characteristics 1--16......................................

Digital IQ Output Connector Pin Assignment (Option 05 Only) 1--19...........

Operating Information

Theory of Operation

RF Input 3--1.......................................................

Down Converter 3--1.................................................

Digital Signal Processing 3--3..........................................

Power Supply 3--4...................................................

External Interface 3--5................................................

Performance Verification

Performance Verification Procedures 4--1.........................

Conventions 4--2....................................................

Brief Procedures 4--3...........................................

Functional Tests 4--4.................................................

Diagnostics 4--8.....................................................

Performance Tests 4--9.........................................

Prerequisites 4--10....................................................

Equipment Required 4--10..............................................

Auto Tests 4--12......................................................

Frequency Checks 4--21................................................

Noise Sideband Checks 4--25...........................................

Amplitude Checks 4--28...............................................

Spurious Response Checks 4--40.........................................

Test Record 4--52.....................................................

Table of Contents

ii RSA3408A Service Manual

Adjustment Procedures

Requirements for Performance 5--1......................................

Equipment Required 5--2..............................................

Preparation 5--3.....................................................

Self Calibration 5--16..................................................

Auto Calibration 5--20.................................................

Reconfiguration of RF Modules 5--33.....................................

Maintenance

Related Maintenance Procedures 6--1....................................

Preparation 6--2.....................................................

Inspection and Cleaning 6--4...........................................

Removal and Installation Procedures 6--7.........................

Preparation 6--7.....................................................

Access Procedure 6--21................................................

Procedures for External Modules 6--22....................................

Procedures for RF Modules 6--27........................................

Procedures for CPU Board and Disk Modules 6--31..........................

Procedures for Mother Board and Daughter Boards 6--41.....................

Procedures for Power Supply Modules on the Instrument Bottom 6--46..........

Procedures for RF1 Modules on the Instrument Bottom 6--51..................

Procedures for Front Panel Modules 6--56.................................

Procedures for Chassis Modules 6--62.....................................

Troubleshooting 6--67...........................................

Troubleshooting Procedure 6--67.........................................

Symptoms and Faulty Modules 6--78.....................................

Required Adjustments After Replacing Modules 6--80.......................

Options

Electrical Parts List

Diagrams

Mechanical Parts List

Replaceable Parts 10--1..........................................

Parts Ordering Information 10--1.........................................

Using the Replaceable Parts List 10--3....................................

Table of Contents

RSA3408A Service Manual iii

List of Figures

Figure 1--1: Definition of the setup and hold time 1--15...............

Figure 1--2: Digital IQ output connector pin assignment 1--19.........

Figure 4--1: Spectrum of the calibration signal (100 MHz, --20 dBm) 4--5

Figure 4--2: Setup display 4--6...................................

Figure 4--3: Reference level setting and A/D overflow indicator 4--7....

Figure 4--4: Spectrogram display 4--7.............................

Figure 4--5: Diagnostic screen 4--8................................

Figure 4--6: Auto test initial screen 4--12............................

Figure 4--7: Performance test result display 4--16....................

Figure 4--8: Hookup for calibrating the power sensor 4--29............

Figure 4--9: Hookup for setting the signal generator output 4--29.......

Figure 4--10: Hookup for checking the absolute amplitude accuracy 4--30

Figure 5--1: Hookup for storing the cal factors in the power meter 5--5.

Figure 5--2: Initial test hookup 5--7...............................

Figure 5--3: Hookup for calibrating the power sensor 5--9............

Figure 5--4: Initial test hookup 5--10...............................

Figure 5--5: Hookup for calibrating the power sensor 5--12............

Figure 5--6: UNCAL display 5--16.................................

Figure 5--7: Calibration menu 5--17...............................

Figure 5--8: Center offset 5--18....................................

Figure 5--9: DC offset 5--19.......................................

Figure 5--10: Auto calibration initial screen 5--20....................

Figure 5--11: Test hookup 5--34...................................

Figure 5--12: Test hookup 5--35...................................

Figure 6--1: Analyzer orientation 6--11.............................

Figure 6--2: External modules 6--12................................

Figure 6--3: RF modules 6--13....................................

Figure 6--4: CPU board and disk modules 6--14.....................

Figure 6--5: Removable hard disk modules (Option 06) 6--15..........

Figure 6--6: Mother board and daughter boards 6--16................

Figure 6--7: Bottom modules -- Power supply 6--17...................

Figure 6--8: Bottom modules -- RF1 6--18...........................

Figure 6--9: Front panel modules 6--19.............................

Table of Contents

iv RSA3408A Service Manual

Figure 6--10: Chassis modules 6--20...............................

Figure 6--11: Guide to removal procedures 6--21.....................

Figure 6--12: Line cord and cabinet removal 6--23...................

Figure 6--13: Front cushion removal 6--24..........................

Figure 6--14: Cabinet modules removal 6--26........................

Figure 6--15: RF modules removal 6--29............................

Figure 6--16: CPU board removal 6--32............................

Figure 6--17: Disk module removal 6--34...........................

Figure 6--18: Hard drive cartridge removal 6--37....................

Figure 6--19: Hard disk drive removal 6--38.........................

Figure 6--20: Outside HDD bracket assembly removal 6--39...........

Figure 6--21: Disk unit removal 6--40..............................

Figure 6--22: Daughter boards removal 6--43........................

Figure 6--23: Mother board removal 6--45..........................

Figure 6--24: Power supply 1 and 2 removal 6--47....................

Figure 6--25: Power supply modules removal 6--49...................

Figure 6--26: RF1 modules removal -- 1 6--52........................

Figure 6--27: RF1 modules removal -- 2 6--54........................

Figure 6--28: Front panel assembly removal 6--57....................

Figure 6--29: Front panel modules removal 6--58....................

Figure 6--30: LCD display removal 6--61...........................

Figure 6--31: Fan and side panel removal 6--63......................

Figure 6--32: Board guide bracket removal 6--64.....................

Figure 6--33: Rear panel removal 6--65.............................

Figure 6--34: Troubleshooting procedure 1 — Power supply system 6--68

Figure 6--35: Troubleshooting procedure 2 — Display and CPU

system 6--69................................................

Figure 6--36: Troubleshooting procedure 3 — Signal path 6--70........

Figure 6--37: Top view of the instrument for cable interconnection 6--75.

Figure 6--38: Bottom view the instrument for cable interconnection 6--76

Figure 6--39: A70 DC power supply board 6--78.....................

Figure 9--1: Block diagram 9--3..................................

Figure 9--2: Interconnect diagram 9--5............................

Figure 10--1: External modules 10--5...............................

Figure 10--2: Front-panel assembly -- 1 10--7........................

Figure 10--3: Front-panel assembly -- 2 10--9........................

Figure 10--4: RF modules 10--11...................................

Table of Contents

RSA3408A Service Manual v

Figure 10--5: Mother board and its daughter boards 10--13.............

Figure 10--6: Disk modules 10--15..................................

Figure 10--7: Disk modules (Option 06) -- 1 10--17.....................

Figure 10--8: Disk modules (Option 06) -- 2 10--19.....................

Figure 10--9: Bottom modules -- Power supply 10--21..................

Figure 10--10: Bottom modules -- RF1 10--23.........................

Figure 10--11: Chassis modules -- 1 10--25............................

Figure 10--12: Chassis modules -- 2 10--27...........................

Figure 10--13: Rackmount 10--29...................................

Table of Contents

vi RSA3408A Service Manual

List of Tables

Table 1--1: Frequency 1--2......................................

Table 1--2: Noise sideband 1--3..................................

Table 1--3: Input 1--4..........................................

Table 1--4: Amplitude 1--5......................................

Table 1--5: Spurious response 1--6...............................

Table 1--6: Acquisition 1--7.....................................

Table 1--7: Trigger 1--8.........................................

Table 1--8: RBW (Resolution Bandwidth) 1--9.....................

Table 1--9: Trace and display line 1--9............................

Table 1--10: Display 1--10.......................................

Table 1--11: Measurement function 1--10...........................

Table 1--12: Analog demodulation accuracy 1--10...................

Table1--13:Pulsemeasurement 1--11.............................

Table 1--14: Digital demodulation (Option 21 only) 1--11.............

Table 1--15: ACLR measurement (Option 27) 1--13..................

Table 1--16: Wireless LAN measurement (Option 29) 1--13............

Table 1--17: Controller 1--14.....................................

Table 1--18: External output connector 1--14.......................

Table 1--19: Power requirements 1--15.............................

Table 1--20: Physical characteristics 1--16..........................

Table 1--21: Environmental characteristics 1--16....................

Table 1--22: Certifications and compliances 1--17....................

Table 1--23: I OUTPUT connector pin assignment 1--19..............

Table 1--24: Q OUTPUT connector pin assignment 1--21.............

Table 4--1: Span and RBW 4--6..................................

Table 4--2: Internal diagnostic program 4--8.......................

Table 4--3: Test equipment 4--10..................................

Table 4--4: Test item selection 4--13...............................

Table 4--5: Procedure for failed test item 4--19......................

Table 4--6: Level linearity test result 4--39..........................

Table 4--7: Spurious measurement 4--51...........................

Table 5--1: Test equipment 5--2..................................

Table 5--2: Compatibility of the spurious correction file 5--15.........

Autres manuels pour RSA3408A

Table des matières

Autres manuels Tektronix Instrument de mesure

Tektronix

Tektronix VM700T Manuel utilisateur

Tektronix

Tektronix S-1 Manuel utilisateur

Tektronix

Tektronix 1L30 Manuel utilisateur

Tektronix

Tektronix DSA8300 Manuel d'utilisation et d'entretien

Tektronix

Tektronix ECO8000 Series Manuel utilisateur

Tektronix

Tektronix P6339A Manuel utilisateur

Tektronix

Tektronix DSA8300 Manuel d'utilisation et d'entretien

Tektronix

Tektronix KEITHLEY 8606 Manuel utilisateur

Tektronix

Tektronix WVR720UP Manuel utilisateur

Tektronix

Tektronix PRISM Manuel utilisateur

Tektronix

Tektronix Keithley SourceMeter 2450 Manuel utilisateur

Tektronix

Tektronix DTM500 Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix 6 series Instructions d'installation et d'entretien

Tektronix

Tektronix RSA5100A Series Manuel

Tektronix

Tektronix 492, 492P Manuel utilisateur

Tektronix

Tektronix 7D01 Manuel utilisateur

Tektronix

Tektronix Keithley 6517-RH Manuel utilisateur

Tektronix

Tektronix WFM8300 Guide de l'administrateur

Tektronix

Tektronix RSA5100B series Manuel d'utilisation et d'entretien

Tektronix

Tektronix Type 130 Manuel utilisateur

Tektronix

Tektronix VM700T Manuel utilisateur

Tektronix

Tektronix Keithley 2290-PM-200 Manuel utilisateur

Tektronix

Tektronix Keithley 6517B/E Manuel utilisateur

Tektronix

Tektronix Keithley 6517B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur