Tektronix P6243 Manuel utilisateur

P6243

1 GHz 10X Active Probe

ZZZ

Instructions

*P070940804*

070-9408-04

Advanced Test Equipment Rentals

www.atecorp.com 800-404-ATEC (2832)

P6243

1 GHz 10X Active Probe

ZZZ

Instructions

www.tektronix.com

070-9408-04

owned by Tektronix or its subsidiaries or suppliers, and are protected by

national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and

pending. Information in this publication supercedes that in all previously

published material. Specifications and price change privileges reserved.

TEKTRONIX, TEK, TEKPROBE, and SureFoot are registered trademarks of

Tektronix, Inc. KlipChip is a trademark of Tektronix. Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

Warranty

Tektronix warrants that this product will be free from defects in materials and

workmanship for a period of one (1) year from the date of shipment. If any such product

proves defective during this warranty period, Tektronix, at its option, either will repair

the defective product without charge for parts and labor, or will provide a replacement

in exchange for the defective product. Parts, modules and replacement products used by

Tektronix for warranty work may be new or reconditioned to like new performance. All

replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the

defect before the expiration of the warranty period and make suitable arrangements for the

performance of service. Customer shall be responsible for packaging and shipping the

defective product to the service center designated by Tektronix, with shipping charges

prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to

a location within the country in which the Tektronix service center is located. Customer

shall be responsible for paying all shipping charges, duties, taxes, and any other charges

for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or

improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish

service under this warranty a) to repair damage resulting from attempts by personnel other

than Tektronix representatives to install, repair or service the product; b) to repair damage

resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a

product that has been modiﬁed or integrated with other products when the effect of such

modiﬁcation or integration increases the time or difﬁculty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE

PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.

TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’

RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE

SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR

BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE

LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADV

ANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

[W2 – 15AUG04]

P6243 Instructions i

Table of Contents

General Safety Summary iii............................

Getting Started 1.....................................

Customer Support 1...................................

Features and Accessories 2..............................

Configuration 6.......................................

Functional Check or Probe Compensation 6................

Operating Basics 9...................................

Maximum Non-destructive Input Voltage 9.................

Input Linear Dynamic Range 9..........................

Ground Lead Length 10.................................

Probe Tip Test Points 14.................................

Specifications 15......................................

Table of Contents

ii P6243 Instructions

List of Figures

Figure 1: Probe Compensation Connections 7...............

Figure 2: Waveform Distortion from Ground Lead Length 10...

Figure 3: Ground Lead Equivalent Circuit 11................

Figure 4: Low-inductance Grounding 12....................

Figure 5: Using a SureFoot Adapter for Grounding 13.........

Figure 6: Using a Probe Tip as a Test Point 14...............

Figure 7: Typical Frequency Response 17...................

Figure 8: Typical Linearity Error vs. VIN 18.................

Figure 9: Typical Input Impedance vs. Frequency 19..........

Figure 10: Typical Non-Destructive Peak Voltage Derating vs.

Frequency 20.......................................

P6243 Instructions iii

General Safety Summary

Review the following safety precautions to avoid injury and prevent

damage to this product or any products connected to it.

Only qualified personnel should perform service procedures.

Injury Precautions

Avoid Electric Overload. To avoid electric shock or fire hazard, do not

apply a voltage to a terminal that is outside the range specified for

that terminal.

Do Not Operate Without Covers. To avoid electric shock or fire hazard,

do not operate this product with covers or panels removed.

Do Not Operate in Wet/Damp Conditions. To avoid electric shock, do

not operate this product in wet or damp conditions.

Do Not Operate in an Explosive Atmosphere. To avoid injury or fire

hazard, do not operate this product in an explosive atmosphere.

Product Damage Precautions

Use Proper Power Source. Do not operate this product from a power

source that applies more than the voltage specified.

Do Not Operate With Suspected Failures. If you suspect there is

damage to this product, have it inspected by qualified service

personnel.

Do Not Immerse in Liquids. Clean the probe using only a damp cloth.

The cloth must be dampened with either isopropyl alcohol or a mild

detergent and water solution. Do not use any other chemicals or

abrasives to clean the probe.

General Safety Summary

iv P6243 Instructions

Safety Terms and Symbols

Terms in This Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that

could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that

could result in damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you

read the marking.

WARNING indicates an injury hazard not immediately accessible as

you read the marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. These symbols may appear on the product:

Protective Ground

(Earth) Terminal

ATTENTION

Refer to Manual

Double

Insulated

DANGER

High Voltage

Autres manuels pour P6243

Table des matières

Autres manuels Tektronix Instrument de mesure

Tektronix

Tektronix SPECMON3 Manuel utilisateur

Tektronix

Tektronix P7260 Manuel utilisateur

Tektronix

Tektronix WVR5000 Instructions de montage

Tektronix

Tektronix KEITHLEY 4200A-SCS-PK2 Manuel utilisateur

Tektronix

Tektronix 2714 Manuel d'utilisation et d'entretien

Tektronix

Tektronix VM700T Manuel utilisateur

Tektronix

Tektronix RSA3408A Manuel utilisateur

Tektronix

Tektronix RSA6100A Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix DSA8300 Manuel utilisateur

Tektronix

Tektronix 3177 Manuel utilisateur

Tektronix

Tektronix WVR6020 Manuel d'utilisation et d'entretien

Tektronix

Tektronix P6248 Manuel utilisateur

Tektronix

Tektronix KEITHLEY 4200A Manuel utilisateur

Tektronix

Tektronix 1L30 Manuel utilisateur

Tektronix

Tektronix KEITHLEY 2600B Series Manuel utilisateur

Tektronix

Tektronix TTR500 series Manuel utilisateur

Tektronix

Tektronix Keithley 6517B Manuel utilisateur

Tektronix

Tektronix WVR5200 Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix P5200 Manuel utilisateur

Tektronix

Tektronix PA4000 Series Manuel utilisateur

Tektronix

Tektronix PRISM MPI Manuel utilisateur

Tektronix

Tektronix RSA3303A Manuel utilisateur

Tektronix

Tektronix MTS415 Manuel utilisateur

Tektronix

Tektronix TLA6402 Instructions d'installation et d'entretien

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur