Tektronix TDS6UP Manuel utilisateur

Instructions

TDS6UP, TDS7UP, and CSA7UP Option CPU

Upgrade Kit

071-1244-00

*P071124400*

071124400

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 1

Service Safety Summary

Only qualified personnel should perform service procedures. Read this Service

Safety Summary and the General Safety Summary in the product service manual

or the instruction manual.

Do Not Service Alone. Do not perform internal service or adjustments of this

product unless another person capable of rendering first aid and resuscitation is

present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may

exist in this product. Disconnect power, remove battery (if applicable), and

disconnect test leads before removing protective panels, soldering, or replacing

components.

To avoid electric shock, do not touch exposed connections.

Service Safety Summary

2TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit

TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 3

Kit Description

This document supports upgrading the NLX CPU board and microprocessor. To

upgrade your NLX CPU board and microprocessor perform each of the

following procedures in order.

Products

TDS6000 Series All serial numbers

TDS7000 Series All serial numbers

CSA7000 Series All serial numbers

Minimum Tool and Equipment List

Table 1: Equipment list

Required tools and equipment Part number

Screwdriver handle 620-440

T-20 Torx tip 640-250

T-15 Torx tip 640-247

1/8inch flat-bladed screwdriver Standard tool

#0 Phillips screwdriver Standard tool

3/16 inch open-end wrench Standard tool

Kit Description

4TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit

Kit Parts List

Circuit/figure

number Quantity Part number Description

11ea 650--4562--00 COMPONENT KIT;MOTHERBOARD/

MICROPROCESSOR UPGRADE;TDS6/7UP

OPTION CPU

21ea 407--4880--01 BRACKET; CD--ROM, REAR DRIVE BAY

CHASSIS, 0.035 CRS

1ea 020--2349--XX SOFTWARE KIT; LICENSE CERTIFICATE,O/S

EASY RESTORE,CERTIFICATE AUTHENTIC-

ITY,WIN98 RESTORE CD

Figure 1: CPU upgrade kit parts

TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 5

Installation Instructions

This section contains all procedures needed to install TDS6UP, TDS7UP, or

CSA7UP Option CPU in the TDS6000, TDS7000, and CSA7000 Series

instruments.

These instructions are for personnel who are familiar with servicing the product.

If you need further details for disassembling or reassembling the product, refer to

the appropriate product manual. Contact your nearest Tektronix Service Center

or Tektronix Factory Service for installation assistance.

CAUTION. To prevent static discharge damage, service the product only in a

static-free environment. Observe standard handling precautions for static-sensi-

tive devices while installing this kit. Always wear a grounded wrist strap,

grounded foot strap, and static resistant apparel while installing this kit.

Remove

This section contains procedures for removal and installation of all mechanical

and electrical modules.

HLine Cord

HTrim (all)

HBottom cover

HLeft and Right covers

HNLX board

HRear chassis

HCD drive bracket

Preparation

WARNING. Before doing this or any other procedure in this manual, read the

Safety Summary found at the beginning of this manual.

Installation Instructions

6TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit

This subsection contains the following items:

HThis preparatory information that you need to properly do the procedures

that follow.

HList of tools required to remove and disassemble all modules.

HProcedures for removal and reinstallation of the electrical and mechanical

modules.

WARNING. Before doing any procedure in this subsection, disconnect the power

cord from the line voltage source. Failure to do so could cause serious injury or

death.

NOTE. Read Equipment list for a list of the tools needed to remove and install

modules in this instrument. See Table 1, on page 3.

Equipment Required. Most modules in the TDS6000, TDS7000, and CSA7000

Series Instruments can be removed with a screwdriver handle mounted with a

size T-15, Torx screwdriver tip. Use this tool whenever a procedure step instructs

you to remove or install a screw unless a different size screwdriver is specified in

that step. All equipment required to remove and reinstall each module is listed in

the first step of the procedure.

Procedures for External Modules

The following procedures are found here and are listed in the order presented.

HLine Cord

HTrim (all)

HBottom cover

HLeft and Right covers

Installation Instructions

TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 7

1. Assemble equipment and locate modules to be removed: Locate the power

switch and AC power cord connector in Figure 2 on page 7.

2. The instrument has a built-in soft power-off function that safely powers off

the instrument when you press the On/Standby switch.

3. Power off the rear panel power switch before servicing the power cord.

4. Orient the instrument: Set the instrument so that the bottom is down on the

work surface and the rear is facing you.

5. Remove line cord: Find the line cord on the rear cover. Pull the line cord

away to remove from the AC power connector.

6. Reinstallation: Do in reverse step 5 to reinstall the line cord.

AC power

cord

Line fuse

holder

Line fuses

AC power cord

connector

Power

switch

Figure 2: Line cord removal

Line Cord

Installation Instructions

8TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit

1. Locate module to be removed: Locate the Trim in the locator diagram. See

Figure3,onpage9.

2. Remove the front panel trim: Use Figure 3 on page 9 as a guide.

a. To prevent the power button from falling out of the front panel trim,

place a piece of tape over the button.

b. Grasp the trim ring by the top edge and pull toward you to detach the

three plastic snaps. (Alternatively, you can use a flat-bladed screwdriver

or other small prying tool to help you detach the snaps.)

c. Swing the bottom of the ring upward and off the front panel.

3. Remove the acquisition trim: Use Figure 3 on page 9 as a guide.

a. Remove the three T-15 Torx screws that secure the acquisition trim to

the instrument.

b. Remove the acquisition trim from the instrument.

4. Remove the top cover trim: Use Figure 3 on page 9 as a guide.

a. Remove the accessory pouch; it snaps off.

b. Remove the four T-15 Torx screws that secure the top cover trim to the

instrument. The T-15 Torx screws also secure the snap studs to the top

cover.

c. Remove the top cover trim from the instrument.

5. Remove the carrying handle and the right/left side trim panels: Use Figure 3

on page 9 as a guide.

a. Remove the T-20 Torx screws that secure the handle to the instrument.

Remove the handle from the instrument.

b. Slide the side trim panels towards the rear of the instrument allowing the

tabs to clear the cover openings, and then pull out to remove the panels

from the instrument.

6. Reinstallation: Do in reverse steps 2 through 5 to reinstall the appropriate

trim.

Trim and Carrying Handle

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tektronix Matériel informatique

Tektronix

Tektronix Keithley 4225-PMU Manuel utilisateur

Tektronix

Tektronix PLOT 10 Manuel utilisateur

Tektronix

Tektronix Colorado Data Systems 53A-334 Manuel utilisateur

Tektronix

Tektronix IPB220 Manuel d'utilisation

Tektronix

Tektronix 067-0832-01 Manuel utilisateur

Tektronix

Tektronix KEITHLEY 7712 Manuel utilisateur

Tektronix

Tektronix BERTScope Manuel

Tektronix

Tektronix TMS 440 SH-3 7708 Manuel utilisateur

Tektronix

Tektronix TMSST1 Manuel utilisateur

Tektronix

Tektronix WVR6020 Manuel d'instructions

Tektronix

Tektronix XD88F14 Manuel utilisateur

Tektronix

Tektronix Keithley KPCI-488LPA Manuel utilisateur

Tektronix

Tektronix Socket 7 TMS109A Manuel utilisateur

Tektronix

Tektronix TMS 101 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur