TeeJet MATRIX Blanchard REB3 Manuel utilisateur

VOYAGER®570G

USER MANUAL

INSTALLATION MANUAL

AUTO BOOM SECTION CONTROL

Blanchard REB3 Controller

www.teejet.com

This installation manual covers installation of MATRIXTM or CenterLine 230BP with Blanchard REB3

controllers. We have endeavoured to deliver a fault free product. To ensure optimal use of the

equipment, we ask you to pay great attention when reading this manual. Regarding responsibility for

use of the product, we refer to our sales and delivery terms - especially paragraph 7, which follows:

Product usage.

7.1 Any use of the product is at the sole risk of the buyer. The buyer

is therefore not entitled to any form for compensation caused by, for

example, any of the following:

• Disturbance to/from any electronic services or products that do

not confirm to the standards for CE marking,

• Missing or poor signal coverage or a succession hereof from

external transmitters/receivers, used by the buyer,

• Functional faults, which apply to or from a PC-program or PC-

equipment, not delivered by the seller.

• Faults that may arise from the buyers negligence to react to

warnings and fault messages from the product, or which can be

traced to negligence and/or absent constant control of the work

carried out in comparison to the planned job.

7.2 When implementing any new equipment the buyer must take great care

and pay attention. Any doubts as to correct operation/use should result

in contacting TeeJet Technologies.

Kind regards,

Mølhavevej 2

9440 Aabybro

Denmark

Tel. +45 9696 2500

Fax +45 96962501

www.teejet.com

www.teejet.com 3

INTRODUCTION TO MATRIXTM AND CL230

The MATRIXTM and Centerline 230BP are combined Guidance and Automatic Boom Section

Control (ABSC) devices that features control of up to 15 boom sections. The MATRIXTM or the

Centerline 230BP connects in parallel to the existing wiring loom to the section valves.

Principle of Operation

The MATRIXTM or Centerline 230BP control the sections valves according to the GPS position and

the GPS guidance makes it possible to avoid overlaps or skips.

The MATRIXTM or Centerline 230BP controls the section valves in automatic mode, and the section

switches should be set to off unless the operator wants to override the auto mode and thus force

spraying.

The MATRIXTM or Centerline 230BP monitors the section switches that controls the valves in

manual mode. The Master switch can be used both in automatic mode as well as in manual mode.

Required Parts

To add Automatically Boom Section Control to a Blanchard REB3 Controller the following part

numbers are required:

MATRIXTM:

Part no. Description

* xxx-xxx MATRIXTM Guidance controller kit

** 990-906 BoomPilot Optima Switch box kit incl. interface (Pos. 4-7 /System Overview)

** 990-907 BoomPilot Optima Switch box kit excl. interface (Pos. 4-6 /System Overview)

45-05626 Power/CAN/Data cable for MATRIXTM (Pos. 2 /System Overview)

45-05648 Power Cable, w/COBO connector (Pos. 3 /System Overview)

* Refer to the MATRIXTM pricelist, ** 990-906 or 990-907

CL230:

Part no. Description

* xxx-xxx CL230 Guidance controller kit

** 990-906 BoomPilot Optima Switch box kit incl. interface (Pos. 3-6 /System Overview)

** 990-907 BoomPilot Optima Switch box kit excl. interface (Pos. 3-5 /System Overview)

* Refer to the CL230BP pricelist, ** 990-906 or 990-907

www.teejet.com

SYSTEM OVERVIEW, MATRIXTM

B AA B

xxx-xxx

xxyyxx

B A

1008-0201

www.teejet.com 5

Pos. Description Part Number

1 MATRIXTM Guidance Controller * xxx-xxx

2 Power/CAN/Data Cable, MATRIXTM 45-05626

3 Power Cable, w/COBO connector 45-05648

4 Section Driver Module 78-05072

5 Switch box, 11 sections + Master 901-000

6 Adapter Cable 198-343

7 Optima Module Interface 900-995

8 Blanchard REB3 Controller -

* Depending on MATRIXTM Kit

SYSTEM DESCRIPTION, MATRIXTM

Pos. Description Part Number

A 8P Connector (Power/CAN/Data to Matrix)

B 9P Connector (Data in/out, Sub.D. Female)

C Fuse (3A) 166-603

D 3P Connector (Power, COBO)

E Fuse (3A) 39-00000

F 2P Connector (System Power)

G 4P Connector (CAN, Matrix and Section Driver Module)

H 2P Connector (Power to Matrix Controller)

I On-off Switch (Switch box)

J 28P Connector (Connection to Switch box)

K 35P Connector (Boom Section I/O to Section Driver Module)

L 14P Connector (CAN to Section Driver Module)

M 16P Connector (Boom Section I/O to OPTIMA Interface)

N 5P Connector (CAN/Power Connection to REB3 Controller)

Connectors and fuses:

Connect the Automatic Boom section kit as shown on the system overview drawing. The kit

includes all necessary parts to get electrical contact with the Blanchard REB3 system.

INSTALLING THE BLANCHARD REB3 KIT

As shown in System Overview, the Optima Module Interface (Pos. 7) serve as a Link between the

Blanchard REB3 Controller (Pos. 8) and the Section Driver Module (Pos. 4).

www.teejet.com

SYSTEM OVERVIEW, CL230

B AA B

xxx-xxx

xxyyxx

B A

1008-0201

www.teejet.com 7

Pos. Description Part Number

1 CL230 Guidance Controller * xxx-xxx

2 Power Cable, w/COBO connector 45-05648

3 Section Driver Module 78-05072

4 Switch box, 11 sections + Master 901-000

5 Adapter Cable 198-343

6 Optima Module Interface 900-995

7 Blanchard REB3 Controller -

* Depending on CL230 Kit

System description, CL230

Pos. Description Part Number

A 4P Connector (GPS Speed - pulses out)

B 9P Connector (Data in/out, Sub.D. Female)

C Fuse (3A) 166-603

D 3P Connector (Power, COBO)

E Fuse (3A) 39-00000

F 2P Connector (System Power)

G 4P Connector (CAN, CL230 and Section Driver Module)

H 2P Connector (Power to CL230 Controller)

I On-off Switch (Switch box)

J 28P Connector (Connection to Switch box)

K 35P Connector (Boom Section I/O to Section Driver Module)

L 14P Connector (CAN to Section Driver Module)

M 16P Connector (Boom Section I/O to OPTIMA Interface)

N 5P Connector (CAN/Power Connection to REB3 Controller)

Connectors and fuses:

Connect the Automatic Boom section kit as shown on the system overview drawing. The kit

includes all necessary connectors to get electrical contact with the Blanchard REB3 system.

INSTALLING THE BLANCHARD REB3 KIT

As shown in System Overview, the Optima Module Interface (Pos. 6) serve as a Link between the

Blanchard REB3 Controller (Pos. 7) and the Section Driver Module (Pos. 3).

www.teejet.com

CONNECTING POS. D TO POWER

Battery Cable (Option)

! When connecting the system to 12V

power it's very important that the polarity

is correct, if not the system will be

damaged.

1008-0189

15/30

If a power connector (Socket) isn't available in the tractor cabin, a optional battery cable can be

used (PN 96ET14).

www.teejet.com

SYSTEM CHECK

After connecting the power connector, it's time to make a system check. To check the system it's

necessary to have full GPS signal so the vehicle must be placed outside.

Check AUTO mode:

Blanchard REB3 Controller / Switch Box:

• Switches on REB3 computer are deactivated once the CAN interface is connected.

• Please use switches on the TeeJet switchbox to manually drive the section valves.

• Switches should be in OFF position when working in Automatic mode.

• The Master switch will control the sprayer and should be ON to enable automatic switching of

the sections.”

MATRIXTM or CL230:

• Turn the Guidance controller on

• Encode the number of sections and the width of each

(Refer to the MATRIXTM or CL230 user manual)

• Wait for GPS signal

• Set the mode to AUTO

• Drive forward (> 2 km/h)

• Observe that all sections and the master valve open.

• Check that the Master valve closes when the Master switch is set off.

• Check hectare counter in the MATRIXTM or CL230 against the Blanchard REB3 controller.

Check MANUAL mode:

MATRIXTM or CL230:

• Set the ABSC mode to MANUAL

Check in the ‘Boom Section Control Screen’ (Matrix or CL230) that the section icons turn off and

on according to the valve/switch status.

Switch Box:

• Set the section switch's on

• Set the Master switch on

• Observe that all sections and the master valve open.

MATRIXTM: CL230:

www.teejet.com

LED’S ON THE SECTION DRIVER MODULE

Section Power: ON when power is available for the section drivers.

I/O error: Should normally be OFF

(Auto Mode: ON when automatic boom switching is active).

CAN Data:  ONisashingwhenitcommunicateswiththeCenterLine230.

CAN Power: ON when power is applied to the CenterLine 230 and the SDM.

LED’S ON THE OPTIMA INTERFACE

On: ON when power is available for the interface.

Tx Bus Can: Flashing when it transmit data.

Rx Bus Can: Flashing when it receive data.

Table des matières

Autres manuels TeeJet GPS

TeeJet

TeeJet Boompilot Matrix Pro 570G Manuel utilisateur

TeeJet

TeeJet MATRIX 570G Manuel utilisateur

TeeJet

TeeJet Matrix Pro 840GS Manuel utilisateur

TeeJet

TeeJet Matrix Pro 570GS Manuel utilisateur

TeeJet

TeeJet RX410p Manuel utilisateur

Manuels GPS populaires d'autres marques

Raven

Raven Cruizer II Manuel

Hama

Hama 53118 Manuel utilisateur

Garmin

Garmin SOUNDER 125 Manuel utilisateur

Garmin

Garmin DEZL 580 Manuel utilisateur

Jigabot

Jigabot EX Manuel utilisateur

Pointer

Pointer Cellocator CelloTrack XT LTE Guide d'installation

Queclink

Queclink GV55LITE Manuel utilisateur

Voxson

Voxson Voxtrack GPS500 Manuel d'instructions

Garmin

Garmin ECHOMAP PLUS Manuel utilisateur

Starcom Systems

Starcom Systems Kylos Compact Manuel utilisateur

Garmin

Garmin 15 H Series Manuel utilisateur

Cobra

Cobra Marine MC 600Ci Manuel utilisateur

Cellocator

Cellocator CelloTrack T Manuel utilisateur

Enfora

Enfora Mini-MT GSM2228UG001 Manuel utilisateur

Magellan

Magellan eXplorist 100 Manuel utilisateur

LTE

LTE G50B Manuel utilisateur

Garmin

Garmin DEZL OTR500 Manuel utilisateur

SkyGolf

SkyGolf SkyCaddie SG1 Manuel utilisateur