Tecnosicurezza TechMaster Manuel utilisateur

TechMaster

User Instructions

 
 
 
 
2 of 28 IU_ TechMaster_07_eng 
User instructions 
 
 TechMaster 
Table of contents 
TABLE OF CONTENTS 2 
IMPORTANT NOTES! 4 
GENERAL INFORMATION 5 
OVERVIEW FUNCTIONS 8 
OPENING THE LOCKS 9 
USERS (OR OVERRIDE USERS): OPENING WITHOUT TIME DELAY 9 
USERS:OPENING WITH TIME DELAY 9 
MANAGER (OR OVERRIDE MANAGER): OPENING WITHOUT TIME DELAY 10 
MANAGER (OR OVERRIDE MANAGER): OPENING WITH TIME DELAY 10 
OPENING WITH DYNAMIC CODES (DALLAS KEY OPTION)10 
OPENING WITH DYNAMIC CODES (PIN OPTION)11 
DUAL MODE OPENING WITHOUT TIME DELAY 11 
DUAL MODE OPENING WITH TIME DELAY 11 
MASTER MENU 12 
TIME &DATE SETTINGS 12 
TIME AND DATE RECOVERY THROUGH DYAMAWEB (OTC SOFTWARE)12 
TIME LOCK SETTINGS 13 
WEEKLY TIME LOCK SETTINGS –ADDING NEW VALUES 13 
WEEKLY TIME LOCK SETTINGS –VERIFY OR DELETE VALUES 14 
CLOSING PERIODS (HOLIDAYS)–ADD NEW VALUES 14 
OPENING PERIODS -ADD NEW VALUES 15 
OPENING PERIODS -VERIFY OR DELETE VALUES 16 
PC CONNECTION 16 
MANAGER MANAGEMENT 16 
DYNAMIC CODES –ENABLING/DISABLING 17 
DYNAMIC CODES ACTIVATION WITH STATIC CODES DELETING 17 
MANAGER MENU 18 
USERS MANAGEMENT 18 
TIME DELAY 18 
VARIABLE TIME DELAY –ADDING NEW VALUES 19 
VARIABLE TIME DELAY –VERIFY OR DELETE VALUES 19 
PC CONNECTION 19 
OVERRIDE MANAGER MENU 20 
OVERRIDE USERS MANAGEMENT 20 
CODE CHANGING 20 
CHANGE CODE FOR STANDARD AND OVERRIDE USERS 20 
CHANGE CODE FOR MANAGER 21 
CHANGE CODE FOR OVERRIDE MANAGER 21 
CHANGE CODE FOR MASTER 21 

IU_TechMaster_07_eng 3 of 28

User instructions

TechMaster

TIME MENU 22

OPENING EXTENSION 22

IMMEDIATE TIME LOCK 22

CONFIGURATION MENU 22

INSTALL LOCKS 22

REMOVE LOCKS 23

LOCK RECLOSURE MODE 23

INSTALL I/O INTERFACE 24

CONFIGURE I/O INTERFACE 24

REMOVE I/O INTERFACE 24

DISPLAY CONTRAST 25

KEYPAD LANGUAGE 25

MEMBRANE TEST 26

SYSTEM INFO 26

DYNAMIC KEYPAD ID AND DYAMAWEB SOFTWARE LICENSE 26

CORRECT DISPOSAL OF THIS PRODUCT: 28

(WASTE ELECTRICAL & ELECTRONIC EQUIPMENT) 28

CONTACTS 28

4 of 28 IU_ TechMaster_07_eng

User instructions

TechMaster

Important notes!

Before installing this product, please carefully read the installation and operating

instructions.

Locks have been designed to correctly operate in a temperature range from -5°C (23°F)

to + 50°C (122°F) and in an environment with non-condensing humidity between 25%

and 90%.

The lock must not be oiled/lubricated/greased.

If installed in normal domestic or office environments, the locks do not require

maintenance; in any case, after 10,000 opening/locking cycles, it is recommended to

conduct a test that verifies the correct and complete operation of the product.

Use only DURACELL™ 9 Volt Alkaline batteries, or battery holders with DURACELL™ 1.5

Volt Alkaline batteries. Alternatively, it is possible to use a 12VDC - 1A power adapter

(p.n. N1212) with relative power supply interface (p.n. T6006).

A long beep together with the message “LOW BATTERY” on the display, indicate a low

battery level which needs to be immediately replaced.

It is strongly recommended to change the default codes before use and to keep safely

the new codes.

Never use codes that can be easily guessed such as 123456, birth dates or based on

other personal information.

After changing a code, perform several opening/closing tests before closing the door.

Should the lock label be removed, warranty is void.

IU_TechMaster_07_eng 5 of 28

User instructions

TechMaster

General information

Using your keypad

Press any button to power up the keypad. LCD which displays:

ENTER CODE

X X –X X X X X X

If more locks are installed, LCD displays:

Enter the lock number to select it.

SELECT LOCK

To enter a code, power up the LCD and enter the corresponding

digits.

LCD automatically switches OFF if no buttons are pressed

within 30s.

To scroll the menu, press .

To confirm an operation or enter a menu press .

To leave a menu and come back to the main menu, scroll the

functions until “EXIT?” and press OK.

To enter a code plus Dallas key (if programmed), enter the code

digits and insert the Dallas key in the keypad reader.

To enter a user provided with Dallas key only (if programmed),

insert the Dallas key in the keypad reader. LCD displays:

DALLAS USER

To start a time delay counting (if programmed), enter a code.

LCD displays:

TIME DELAY

00:59

To stop a time delay counting (if programmed), press and

then confirm with

STOP DELAY

COUNTING?

After time delay counting, LCD displays open window counting:

Press and enter a code for opening.

OPEN WINDOW

00:01

If a wrong code is entered, LCD displays the message:

WRONG CODE

If a wrong dynamic/activation code is entered, LCD displays the

message:

WRONG DYNAMIC

CODE

6 of 28 IU_ TechMaster_07_eng

User instructions

TechMaster

If a dynamic/activation code is entered more than 30 minutes

before its beginning validity time, LCD displays:

WRONG DYNAMIC

CODE

If a dynamic/activation code is entered more than 30 minutes

later than its beginning validity time, LCD displays:

WRONG DYNAMIC

CODE

To open or access the menu in dual mode (if programmed),

enter the first code. LCD displays:

Then, enter the second code.

ENTER 2° CODE

X X –X X X X X X

Using your Keypad in Scramble mode (required for class C)

Scramble mode is an additional security which allows to enter a code without using always the

same keys. User ID instead can still be entered as well as the Configuration menu code

To enter an opening code or a menu code in scramble mode, follow the steps below:

Enter the user ID. LCD displays:

ENTER CODE

[5] x x x x x x x

Enter the user code by pressing key or , respectively to increase

or decrease by 1 the digit selected ([X]). Press to confirm and to

switch to the next digit. All digits already entered are indicated by

capital symbol.

After entering the last digit, press to confirm the code.

Press to come back to the previous digit. When the first digit is

selected, press again to enter again the user ID.

ENTER CODE

X X X X X [ 8 ] x x

Shortcuts

Press and hold for 2 seconds the button related to the needed function:

= Change Manager code (01), users, override users, Master and Manager ovr (if configured)

= PIN entering for dynamic codes (after dynamic codes activation)

= Test mode

IU_TechMaster_07_eng 7 of 28

User instructions

TechMaster

= access to Manager menu, Manager ovr menu (if configured) Change code menu, Time

menu, Configuration menu and Master menu.

= System info and time and date info

= Exit and back to the main menu

= Master menu

User properties and default codes

Users can be programmed for opening with code only, code + Dallas key or with Dallas key only.

It is also possible to set a dual mode opening: in this case, entering the two users codes is

required to open the lock.

Default codes are:

Master: 1-2-3-4-5-6-7-8.

Manager: 123456.

Users from 02 to 90: 02-020202, 03-030303, and so on. They always open with time delay if

programmed.

Override users: through to the setup software, it is possible to configure users in between 10

and 90 (10-101010, 11-111111, and so on) as override users. They always open without time

delay.

For class C, all users codes, including Master and Manager, are 8-digits type.

Users from 02 to 90 and Override users have a default code such as 02-02020202, 03-03030303,

and so on.

The table below reports the functions for the main users.

Master

Manager

Access to Master Menu

Set time and date

Set Time Lock periods

Audit download

Manager Management

Enable/disable OTCs

Change code

PC Link

Access to Manager Menu

Standard users management

Override users management

Set time delay

Set variable time delay

PC Link

Audit download

Opening

Code changing

Set opening extension

Set immediate time lock

Override manager

Configuration menu

Access to Ovr. Manager menu

Override users management

Code changing

Install/remove locks

Set display contrast

Change language

8 of 28 IU_ TechMaster_07_eng

User instructions

TechMaster

Test mode

Check system Information

Override users

Standard users

Opening

Change code

Opening

Set opening extension, if enabled

Set immediate time lock, if enabled

Code changing

This user manual describes the standard programming. According to such programming and

unless different requests made while ordering the product, an opening can be performed by

entering single users codes (no dual mode) and without time delay. Thus, the user manual must

be adapted according the configuration selected.

It is strongly recommended to change the default codes before using the lock.

Overview functions

Lock opening

After entering an opening code, it is possible to open the lock within 3 seconds. It’s no necessary

instead with motorized locks: in this case indeed, the motor moves the bolt which remains in

opening position for about 8 seconds before returning in closing position. In the manual closing

version instead, the bolt can be closed by pressing key for few seconds.

Penalty

Four consecutive wrong codes initiate a four-minutes penalty time. During this period, LCD

displays the message “PENALTY” and no operation is allowed.

For class C, the minimum penalty time is of 5 minutes.

Time Delay

Programmable time delay in between 0 and 99 minutes. Programmable opening window in

between 1 and 19 minutes.

Dallas keys

It can be programmed for any lock. Available as option for Manager and users (not for Master).

TechMaster keypad only works with Dallas keys created by TECNOSICUREZZA. Upon express

request, the keypad can be set in order to work also with different Dallas key models.

Power supply

Lock can be powered with:

an ALKALINE 9V battery located in the battery compartment below the keypad;

an internal battery box provided by Tecnosicurezza (6 ALKALINE 1.5 batteries);

IU_TechMaster_07_eng 9 of 28

User instructions

TechMaster

A power adapter (ref. N1212) with power supply interface (ref. T6005/W or T6005) both

provided by Tecnosicurezza.

Low battery warning

A long beep together with the message “LOW BATTERY” on the display, indicates a low battery

level which should be immediately replaced.

Silent alarm

With this function enabled, enter an opening code increasing or decreasing by one number

the last code digit (ex. 03-030304 or 03-030302 instead of 03-030303): the lock opens and

simultaneously the output of the alarm interface or I/O interface is activated.

Tamper alarm (required for class C)

This function provides a blocking of the system and displays a warning message “ANTI_TAMPER

ALARM” whenever the keypad is removed from the door, or the battery compartment get

opened. Insert a valid code to unblock the keypad and restore the normal functioning.

Audit

The lock saves the last 6000 operations with time, date, user and operations description. The

keypad can save the last 250 operations. It is possible to download the events for locks and

keypad by using the Tecnosicurezza DMT Audit software. For further information refer to the

IU_DMT_Audit_XX.

IMPORTANT

Some options/characteristics reported in this user manual, can only be used if previously

programmed through the setup software. Therefore, please refer to the user manual

IU_TechMaster_setup_XX. Please contact Tecnosicurezza for further information.

Opening the locks

Users (or Override users): opening without time delay

Power up the keypad. Enter an opening code and insert the Dallas key,

if programmed. LCD displays:

OPEN

Open the lock within 3 seconds.

Users: opening with time delay

Power up the keypad. Enter an opening code and insert the Dallas key,

if programmed.

LCD displays the time delay counting:

TIME DELAY

00:59

At time elapsed, the LCD displays the open window counting time.

OPEN WINDOW

00:01

Press , LCD displays:

ENTER CODE

X X –X X X X X X

10 of 28 IU_ TechMaster_07_eng

User instructions

TechMaster

Enter an opening code and insert the Dallas key, if programmed. LCD

displays:

OPEN

Open the lock within 3 seconds.

Manager (or Override Manager): opening without time delay

Power up the keypad. Press for opening with Manager code or

press it two times for opening with Manager Ovr code. LCD displays:

MANAGER CODE

X X X X X X

Enter Manager code and insert the Dallas key, if programmed (or enter

Manager Ovr code and insert the Dallas key, if programmed). LCD

displays:

OPEN

Open the lock within 3 seconds.

Manager (or Override Manager): opening with time delay

Power up the keypad. Press for opening with Manager code or

press it two times for opening with Manager Ovr Code. LCD displays:

MANAGER CODE

X X X X X X

Enter Manager code and insert the Dallas key, if programmed (or enter

Manager Ovr Code and insert the Dallas key, if programmed). LCD

displays the time delay counting:

TIME DELAY

00:59

Once the time delay has elapsed, the LCD displays the open window

counting time.

OPEN WINDOW

00:01

Press , LCD displays:

ENTER CODE

X X –X X X X

Press for opening with Manager code or press it two times for

opening with Manager Ovr code. LCD displays:

MANAGER

X X X X X X

Enter Manager code/Manager Ovr code and insert the Dallas key, if

programmed. LCD displays:

OPEN

Open the lock within 3 seconds.

Opening with dynamic codes (Dallas key option)

Power up the keypad. Insert the Dallas dynamic key in the Dallas

reader. LCD displays:

DYNAMIC CODE

X X X X X X X X X

Enter the dynamic code and press . LCD displays:

OPEN

Open the lock within 3 seconds.

If programmed by the software Dyama or DyamaWeb for dynamic

codes creation, LCD displays the closing code when the bolt re-closes.

Please refer to the user manuals IU_Dyama_XX or IU_DyamaWeb_XX

for further information.

CLOSING CODE

179

WARNING: dynamic codes must be used respecting the sequence of

activation time in which they have been created by the software

DYNAMIC CODE

DELETED

Autres manuels pour TechMaster

Table des matières

Autres manuels Tecnosicurezza Verrouillage

Tecnosicurezza

Tecnosicurezza MiniTech Manuel utilisateur

Tecnosicurezza

Tecnosicurezza AuditLine T6530/DL Manuel utilisateur

Tecnosicurezza

Tecnosicurezza T6530/DL Manuel utilisateur

Tecnosicurezza

Tecnosicurezza DigiTech Manuel utilisateur

Tecnosicurezza

Tecnosicurezza MiniTech Manuel utilisateur

Tecnosicurezza

Tecnosicurezza StraightBolt EM3520 Manuel utilisateur

Tecnosicurezza

Tecnosicurezza T9510/BR Manuel utilisateur

Tecnosicurezza

Tecnosicurezza Pulse T6430 Manuel utilisateur

Tecnosicurezza

Tecnosicurezza TechMaster Manuel utilisateur

Tecnosicurezza

Tecnosicurezza MiniTech Manuel utilisateur

Tecnosicurezza

Tecnosicurezza DigiTech Manuel utilisateur

Tecnosicurezza

Tecnosicurezza TechMaster Manuel utilisateur

Tecnosicurezza

Tecnosicurezza MiniTech T52 Series Manuel utilisateur

Tecnosicurezza

Tecnosicurezza Pulse Pro Manuel utilisateur

Tecnosicurezza

Tecnosicurezza Pulse Pro T6630/GRP Manuel utilisateur

Tecnosicurezza

Tecnosicurezza TechMaster Manuel utilisateur

Tecnosicurezza

Tecnosicurezza Pulse 2 Manuel utilisateur

Tecnosicurezza

Tecnosicurezza TechMaster T9530/GR Manuel utilisateur

Tecnosicurezza

Tecnosicurezza MiniTech TSMINI-4 Manuel

Tecnosicurezza

Tecnosicurezza MiniTech Instructions de fonctionnement

Tecnosicurezza

Tecnosicurezza MiniRotoboIt UR4020 Guide de l'utilisateur

Tecnosicurezza

Tecnosicurezza Pulse Pro Manuel utilisateur

Tecnosicurezza

Tecnosicurezza DigiTech Series Manuel utilisateur

Tecnosicurezza

Tecnosicurezza KL3909 Instructions d'installation

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur