TE Connectivity 59974-1 Manuel utilisateur

1 of 5

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

Instruction Sheet

408-6757

25 FEB 15 Rev F

WIRE SIZE

(AWG)

DIE ASSEMBLY FOR●

AMPLI-BOND* TERMINALS

AND SPLICES (408-1758)

TERMINYL* TERMINALS

AND SPLICES (408-1729)

AMPOWER* PRE-INSULATED

TERMINALS AND SPLICES (408-1729)

48752-1 Mod. W

47820

---

48753-1 Mod. W

47821

---

48754-1 Mod. W

47822

---

48755-1 Mod. W

47823

●Reference instruction sheet in parenthesis for information on die assemblies.

Figure 1

1. INTRODUCTION

Hydraulic Hand Tool 59974-1 is designed for crimping the terminals and splices listed in Figure 1. Read these

instructions thoroughly before using the hand tool.

NOTE

Dimensions in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for

identification only and are not drawn to scale.

Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

2. DESCRIPTION (Figure 1)

The hand tool has a stationary lever and a movable lever. These levers are compressed to pump hydraulic fluid

behind the ram, moving it forward and thereby closing the dies. After the crimping is complete, the movable

lever is turned to depress the plunger, and the moving die retracts to its original position, completing the

crimping cycle.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Hydraulic Hand Crimping Tool 59974-1

Stationary (Reservoir)

Lever

Cap

Setscrew

Plunger

(Pressure

Release)

Movable Lever

Latch Pin

(Removed)

Striker (Shown in Actuated

Position to Depress Plunger)

Ram (Advanced to Show

Setscrew for Moving Die

Yoke

(Opened)

Setscrew (Holds

Stationary Die)

ORIGINAL INSTRUCTIONS

408-6757

Rev F

2 of 5

3. DIE INSERTION AND REMOVAL

1. Pull out the latch pin and open the yoke. See Figure 1.

2. Advance the ram slightly to gain access to the moving die setscrew. Note that the stationary die is

held in place by a setscrew.

3. Before inserting the dies, refer to the instruction sheet packaged with the dies for detailed instructions:

insert or remove dies, as necessary, by following the procedures given in the instruction sheet.

4. CRIMPING PROCEDURE

1. Strip the wires to the dimensions specified in the instructions packaged with the dies (see Figure 1).

2. Insert the terminal or splice in the stationary die according to the instruction sheet packaged with the

dies.

DANGER

Ensure latch pin is fully inserted before operating hand tool.

3. Pump the movable lever until the moving die grips the terminal or splice.

CAUTION

Do not deform the wire barrel of the terminal or splice.

4. Insert the stripped wire into the wire barrel of the terminal or splice.

5. Continue pumping the moveable lever. There may be a slight audible click, indicating that the pump

has shifted into the high-pressure stage. Continue pumping the moveable lever. When the dies have

bottomed, there will be an audible “pop”. This indicates that the crimp is complete.

CAUTION

Potential damage to the tool may occur if the following Step 6 is not taken.

6. Retract movable die by opening the movable handle to the full open position, turn the movable handle

(to actuate striker), DO NOT TURN THE MOVABLE HANDLE WHILE IN THE CLOSED POSITION

AS YOU WILL DAMAGE THE PLUNGER (PRESSURE RELEASE), compress handles to depress

plunger (pressure release). Movable die will now retract. See Figure 1.

7. Remove the latch pin, open the yoke, and remove the crimped terminal or splice.

NOTE

If the terminal or splice sticks in the die after crimping, apply a rocking action to remove it from the die.

8. Inspect the crimped terminal or splice according to the inspection procedure in the instruction sheet

packaged with the dies.

5. MAINTENANCE AND INSPECTION

It is recommended that a maintenance and inspection program be performed periodically to ensure dependable

and uniform terminations. Though recommendations call for at least one inspection a month, frequency of

inspection depends on:

1. The care, amount of use, and handling of the hand tool.

2. The presence of abnormal amounts of dust and dirt.

3. The degree of operator skill.

4. Your own established standards.

The hand tool is inspected before being shipped; however, it is recommended that the tool be inspected

immediately upon arrival at your facility to ensure that the tool has not been damaged during shipment.

5.1. Daily Maintenance

1. Hand tool should be immersed (levers partially closed) in a reliable commercial degreasing compound

to remove accumulated dirt, grease, and foreign matter. When degreasing compound is not available,

tool may be wiped clean with a soft, lint-free cloth. Do NOT use hard or abrasive objects that could

damage the tool.

408-6757

Rev F

3 of 5

2. Make certain that the retaining pins are in place and that they are secured with retaining rings.

CAUTION

Do not remove the retaining pins as permanent damage to the tool could result.

3. All pins, pivot points, and bearing surfaces should be protected with a THIN coat of any good SAE 20

motor oil. Do NOT oil excessively.

4. When the tool is not in use, keep levers closed to prevent objects from becoming lodged in the dies.

Store the tool in a clean, dry area.

5.2. Hydraulic Fluid Level Inspection (Figure 2)

1. Turn the tool upside down and clamp it in a vise so that the tool levers are in an upright position.

2. Release all pressure in the tool according to Step 6 of Section 4, CRIMPING PROCEDURE.

3. Turn the movable lever, and allow the lever to close until it stops. Be sure not to depress the plunger

when closing the lever.

NOTE

Keep lever in CLOSED position for remaining steps in this procedure.

4. Loosen the setscrew in cap of the stationary (reservoir) lever. See Figure 1.

5. With a view from the lever grip end, turn the lever COUNTERCLOCKWISE and remove the entire

reservoir lever to expose the bladder.

6. Remove the magnetic filler plug. If the bladder is full, no further check is necessary and the tool can

be re-assembled. If fluid level is low, proceed to the next step.

7. Fill the bladder with fluid. Recommended fluid is Dexron II, which is a transmission fluid available in

automotive parts and department stores. Use care to prevent air bubbles from forming while pouring

the fluid.

8. Refill the bladder to point of overflow, and replace the filler plug.

9. Re-assemble the stationary lever and tighten the cap setscrew. The tool is now ready for use.

Figure 2

5.3. Periodic Inspection

It is recommended at least one inspection a month. The inspection frequency should be based on the amount

of use, ambient working conditions, operator training and skill, and your company's established standards.

Dexron is a trademark.

Movable Lever in

Closed Position

Magnetic

Filler Plug

Pour Fluid

Here

Bladder

Tool Positioned

in Vise

408-6757

Rev F

4 of 5

Lubrication

Keep all pins, pivot points, and bearing surfaces lubricated with SAE 20 motor oil as follows:

Tool used in daily production-lubricate daily

Tool used daily (occasionally)-lubricate weekly

Tool used weekly-lubricate monthly

Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

Visual Inspection

1. Make certain all retaining pins are in place and secured with retaining rings. If replacements are

necessary, refer to parts listed in Figure 3.

2. Inspect head assembly for worn, cracked, or broken areas. If damage is evident, return the tool for

evaluation and repair. See Section 6, REPLACEMENT AND REPAIR.

Crimping Pressure Inspection

Check the crimping pressure to ensure that dies are fully bottomed before pressure is reduced by the

internal bypass valve. The inspection should be performed using each set of dies that will be used in the

head.

1. Install the dies according to Section 3, DIE INSERTION AND REMOVAL, and the instruction sheet

packaged with the dies.

2. Select the wire and terminal or splice for the dies being used.

3. Place the terminal or splice in the dies according to the instruction sheet packaged with the dies.

4. Perform the crimping procedure as described in Section 4, CRIMPING PROCEDURE, Steps 3

through 5. Do not release the hydraulic pressure at this time.

5. Check the clearance between bottoming surfaces of the crimping dies. If clearance is 0.025 mm

[.001 in.] or less, crimp pressure is satisfactory. If clearance exceeds 0.025 mm [.001 in.], crimp

pressure is considered not satisfactory. See Section 6, REPLACEMENT AND REPAIR.

If the tool conforms to these inspection procedures, lubricate it with a THIN coat of any good SAE 20

motor oil and return it to service.

6. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to

prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by

TE Connectivity to ensure quality and reliability. Order replacement parts through your TE Representative, or

call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair service, call 1-800-526-5136.

7. REVISION SUMMARY

Updated document to corporate requirements

Added new CAUTION after Paragraph 4.5

Added new text to Paragraph 4.6

408-6757

Rev F

5 of 5

REPLACEMENT PARTS

ITEM

PART NUMBER

DESCRIPTION

QTY PER TOOL

4-21012-0

SETSCREW

306209-1

PIN, Latch

21045-6

RING, Retaining

301744

PIN, Retaining

Figure 3

63.5

[2.50]

127 [5.0]

508 [20.0]

Weight: 3.6 kg [8 lbs]

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2063536-1 Manuel utilisateur

TE Connectivity

TE Connectivity 1-45216-0 Manuel utilisateur

TE Connectivity

TE Connectivity 220189 Series Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 4-1579001-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-1 Manuel utilisateur

TE Connectivity

TE Connectivity HDP-400 Guide de référence

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

TE Connectivity

TE Connectivity 543344- 1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 4-1579001-6 Manuel utilisateur

TE Connectivity

TE Connectivity 2391435-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity CERTI- CRIMP Series Manuel utilisateur

TE Connectivity

TE Connectivity 575937 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539 664-2 Manuel utilisateur

TE Connectivity

TE Connectivity CERTI-CRIMP 90066-7 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III 2161732-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur