Symbol SYMBOL LS7808 Manuel utilisateur

Symbol LS7808 Horizontal Slot Scanner

Mounting Instructions and EAS Installation Guide

2 Symbol LS7808 Horizontal Slot Scanner

Motorola reserves the right to make changes to any product to improve reliability,

function, or design.

Motorola does not assume any product liability arising out of, or in connection

with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise

under any patent right or patent, covering or relating to any combination, system,

apparatus, machine, material, method, or process in which Motorola products

might be used. An implied license exists only for equipment, circuits, and

subsystems contained in Motorola products.

MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are

registered trademarks of Motorola, Inc. Other product names mentioned in this

manual may be trademarks or registered trademarks of their respective

companies and are hereby acknowledged.

Motorola, Inc.

One Motorola Plaza

Holtsville, N.Y. 11742-1300

http://www.symbol.com

Warranty

For the complete Motorola hardware product warranty statement, go to:

http://www.symbol.com/warranty.

Patents

This product is covered by one or more patents. For patent information go to:

http://www.symbol.com/patents.

Mounting Instructions and EAS Installation Guide 3

Introduction

This guide includes two sections: Section I provides scanning

information, typical layouts, installation/mounting information and

mounting dimensions for the Symbol LS7808-SR20007TCR and

LS7808-SR2X009SCR horizontal slot scanners; Section II provides

installation instructions for EAS.

Configurations

The Symbol LS7808 is available in the following configurations.

NOTE If you are replacing a Symbol LS5800-I200TC or

LS5800-I200TN scanner with the Symbol

LS7808-SR20007TCR or LS7808-SR2X009SCR, mounting

buckets are interchangeable.

Configuration Features

Symbol LS7808-SR20007TCR Standard (tin oxide) glass window; twilight

black; Checkpoint

EAS; RoHS compliant.

Symbol LS7808-SR20009SCR Scratch proof (sapphire) glass window;

stainless steel bezel top; Checkpoint

EAS;

RoHS compliant.

Symbol LS7808-SR22009SCR Scratch proof (sapphire) glass window;

stainless steel bezel top; Checkpoint

EAS;

RoHS compliant; Remote Scanner

Management (RSM) ready “out of the box.”

A stainless steel in-counter mounting kit (p/n 12-17206-02R) is required for all

models. See

Installation/Mounting on page 6

for mounting/installation

instructions.

4 Symbol LS7808 Horizontal Slot Scanner

Section I - Scanning, Layouts, Mounting

Active Scan Area

The Symbol LS7808 is designed to be installed in the counter, with the

face of the scanner flush with the counter top.

The figure below shows a typical layout. The dotted area depicts the

active scan area and the arrow shows the optimal direction of product

flow. The scanner’s active scan zone extends about 6 in. (15.24 cm)

above the window and is angled at approximately 38° from the counter.

Typical Layouts

The illustrations below show typical Symbol LS7808 installations

with various options, as noted. For best operating results, locate

the power supply at least 4 in. (10.16 cm) below the scanner

chassis or 2 in. (5.08 cm) away laterally.

Scanner

Window

Product Flow

Mounting Instructions and EAS Installation Guide 5

Without Auxiliary Scanner and EAS

With Auxiliary Scanner

Scanner

Host

Power Supply (optional)

Synapse Cable

(Optional)

Host Interface Cable

Scanner

Host

Power Supply

Synapse Cable

(Optional)

Host Interface Cable

6 Symbol LS7808 Horizontal Slot Scanner

With EAS

Installation/Mounting

The Symbol LS7808-SR20007TCR and LS7808-SR2X009SCR require

a stainless steel in-counter mounting kit (p/n 12-17206-02R) for

installation. There are two options for installing this model using the

kit, also known as a bucket. The steps for installation options A and B

follow.

Scanner

Host

EAS

Antenna Box

Synapse Cable

(Optional)

Host “Y” Cable

Power Cable (optional)

Power Supply (optional)

EAS Control Cable

EAS Control Box

Mounting Instructions and EAS Installation Guide 7

Option A - Resting on the Counter Top

1. Cut a hole in the counter 6.26 in. (159 mm) square, as shown in the

illustration below.

2. Place the bucket into the hole.

3. Unscrew and remove the scanner connector cover.

4. Place the scanner on the counter near the bucket.

5. Route the cables from beneath the hole and attach to the scanner

as shown in Typical Layouts on page 4.

6. Reattach the connector cover and tighten the screws.

7. Lower the scanner into the bucket.

IMPORTANT Always reattach the connector cover and tighten the

screws after all cables are connected to the scanner ports. The

connector cover ensures that all cables are properly situated and

connections are secure.

Counter Hole 6.81 in. ±0.06

173 mm ±1.5

~3.5 in.

89 mm

7.91 in.

201 mm

6.26

159

8 Symbol LS7808 Horizontal Slot Scanner

Option B - Flush with the Counter Top

1. On the counter top, measure two concentric squares: an inside

square of 6.81 in. (173 mm) and an outside square of 7.91 in. (201

mm), as shown in the illustration below.

2. Cut out the 6.81 in. (173 mm) inner square.

3. With a router set to a depth of .05 in. (1.2 mm), route out the outside

square. The corner radius should not exceed 0.2 in. (5 mm). Ensure

the outside square is concentric with the inside square.

4. Place the bucket into the hole.

5. Unscrew and remove the scanner connector cover.

6. Place the scanner on the counter near the bucket.

7. Route the cables from beneath the hole and attach to the scanner as

shown in Typical Layouts on page 4.

8. Reattach the connector and tighten the screws.

9. Lower the scanner into the bucket.

IMPORTANT Always reattach the connector cover and tighten the

screws after all cables are connected to the scanner ports. The

connector cover ensures that all cables are properly situated and

connections are secure.

R 0.20 in. max

R 5 mm max

7.91 in. min

201 mm min Counter Hole 6.81 in. ±0.06

173 mm ±1.5

7.91 in.

201 mm

~3.5 in.

89 mm

0.27 in

6.8 mm

0.39 in min

10 mm min

7.91 in.

201 mm

~3.5 in

89 mm

Mounting Instructions and EAS Installation Guide 9

Section II - Electronic Article Surveillance (EAS)

The Symbol LS7808-SR20007TCR and LS7808-SR2X009SCR include

an EAS antenna. The scanner and EAS system can operate

independently of each other, or using an exclusive interlock feature. The

deactivation range is mapped suitable to the scanning range, so both

can be accomplished almost simultaneously. The interlock feature

requires a good decode signal to activate the EAS system.

The scanner’s integrated EAS deactivation antenna requires an EAS

host cable. This Y-cable connects to the scanner’s host port at one end

and splits to the host and the EAS system at the other end.

Checkpoint® EAS Model Compatibility

The EAS cable is intended for use with Checkpoint CP-VII and CP-IX

systems. It does not support CP-IV and other low-power receiver-based

EAS deactivation systems.

Considerations

The Checkpoint EAS system operates by generating a periodic burst of

energy which deactivates EAS tags brought into proximity of the

scanner. Unless proper precautions are taken, this field may interfere

with the scanner’s operation.The following criteria must be observed

when installing EAS:

• The antenna box must be as far as possible (minimum 6 in. or

15.24 cm) from the scanner.

• The scanner (with integrated EAS antenna), EAS antenna box, EAS

control cable and EAS controller box must be as far as possible from

the scanner’s host and power cables. For a typical EAS installation,

see Typical Layouts on page 4.

• The counter in which the EAS antenna is installed must be made of

non-metallic materials. Metallic counters or metal objects in proximity

to the scanner interfere with EAS Deactivation.

CAUTION Do not attempt to activate the interlock feature. Activation

instructions are for a Symbol qualified technician only.

10 Symbol LS7808 Horizontal Slot Scanner

• If two antenna boxes are connected to the controller box, each of

them must be connected to a scanner (antenna). If one is left

unconnected, communications errors may occur. If only one antenna

is in use, disconnect the other antenna box at the controller box.

Deactivation for Sensormatic EAS System

To interface to Sensormatic systems, contact Symbol Product

Management.

Connecting the EAS Antenna

A host interface cable with EAS leads from Symbol is required. The EAS

leads are connected by Checkpoint Systems, Inc.

Contact your local Checkpoint representative to install the EAS cable to

the Checkpoint Deactivation System. To contact a representative, call

800-257-5540 (in the United States) or 609-848-1800 (outside the United

States).

Connecting the EAS Interlock

To activate the EAS system independent of the scanner, or combine the

two in an exclusive interlock feature, refer to the appropriate parameters

in the Symbol LS7808 Horizontal Slot Scanner Product Reference

Guide, p/n 72E-73952-xx.

The interlock feature discourages “sweetheart shopping.” These are

instances where some customers are favored and not all items are

scanned. The interlock prohibits the deactivation of the EAS tag without

the item being scanned first.

Autres manuels pour SYMBOL LS7808

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Symbol Lecteur de codes-barres

Symbol

Symbol MicroKiosk MK1000 Manuel d'installation et d'exploitation

Symbol

Symbol LS 4071 Manuel utilisateur

Symbol

Symbol LS 3020 Mode d'emploi

Symbol

Symbol LS 5300 Manuel utilisateur

Symbol

Symbol LS9203 Manuel

Symbol

Symbol DS3478 Manuel utilisateur

Symbol

Symbol SE955 Guide de configuration rapide

Symbol

Symbol MicroKiosk MK1000 Manuel d'installation et d'exploitation

Symbol

Symbol LS 7708 Manuel d'installation et d'exploitation

Symbol

Symbol WSS 1000 Manuel utilisateur

Symbol

Symbol Symbol LS3478-FZ Manuel utilisateur

Symbol

Symbol LS 4005i-I573 Manuel utilisateur

Symbol

Symbol CRD 2700-4200E Manuel utilisateur

Symbol

Symbol P370 Manuel utilisateur

Symbol

Symbol LS 3070 Manuel utilisateur

Symbol

Symbol Symbol DS6708 Manuel utilisateur

Symbol

Symbol LS1203 Manuel utilisateur

Symbol

Symbol Symbol LS2208 Manuel d'installation et d'exploitation

Symbol

Symbol PPT 8800 Manuel d'installation et d'exploitation

Symbol

Symbol LS 2000MX series Manuel utilisateur

Symbol

Symbol Symbol LS9208i Manuel utilisateur

Symbol

Symbol Symbol LS2208 Manuel utilisateur

Symbol

Symbol LS 3408 Manuel utilisateur

Symbol

Symbol MC9090-G RFID Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur