Sylvac PS16 V2 Manuel utilisateur

MEASURING BENCH PS16 V2

BANC DE MESURE PS16 V2

MESSBANK PS16 V2

INSTRUCTIONS

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

1 3 2 16 12

13 14

1598710

Description

1. MODE button

2. SET button

3. “Favourite” button

4. Mini-USB

5. Compartment for battery CR2477 or CR2032.

6. Adapter CR2477/CR2032

7. Adjustable release lever

8. Optional stop

9. Travel stop

10. Force adjustment knob

11. Anvils locking screw Ø1.5mm

12. Moving measurement spindle for Sylvac Ø1.5 probe and Cary compatible probe

13. Fixed measurement spindle for Sylvac Ø1.5 probe and Cary compatible probe

14. Moveable tailstock

15. Tailstock position locking screw

16. Measurement unit

17. Proximity cable housing

Handling

Unblocking the transport mode axes

Place the 2 optional stops (on the front and rear of the unit) in their middle position.

First use

For the rst use, after a complete stop (off) or battery change, the instrument will

request a new reference measurement (--rEF--).

Move the measurement axis to the end of its run, (fully entered)

1. General usage remarks

• The original anvils assembled on both measurement axes are lapped in position

to guarantee an optimum measurement. Any disassembly of these anvils can

lead to a reduction in the accuracy of the instrument.

• The tailstock was positioned to have 0.5mm prestress in the probe zero position.

• Activating the lever opens the anvils. Releasing the release lever too sharply

can have a harmful inuence on the probes and the measurement accuracy.

• It is advisable to check the reference (origin) during use.

• Monitor the cleanliness of the moving spindle. If necessary clean with light ben-

zene. Using a cloth that could leave residual particles is not recommended.

• Certain components, notably the headstock clamp screws are sealed after

assembly and consequently must not be removed. Any work on these compo-

nents by a third party can lead to loss of the guarantee.

2.1 Adjustable release lever

The movable measuring spindle is retracted by means of the adjustable lever (7). The

position of the lever can be adjusted to suit the location of the workpiece. In order to

change the position, pull the lever out axially and move it to the desired position.

2. Use

2.2 Optional stops

The PS16 V2 is equipped with 2 optional stops (at the front and back of the

instrument). Used in combination, they allow the travel to be restricted in 2

directions (opening/closing) so that the position and the measuring travel can

be adjusted to suit the workpiece.

This prevents the anvils from coming back into contact (0) and having to repeat the

full travel with each measurement. The stop is engaged by pushing the radial button

(8).

The stop positions are adjusted by positioning the release lever (see chap. 2.1). If 2

stops are being used, the release lever has a set position that cannot be modied.

2.3. Measuring force

The measuring force can be adjusted by moving the adjustment knob (10) as follows:

unscrew the knob (~1/2 a turn), position it at the required force and re tighten it.

Optimise the measuring force setting for workpiece weight and deformation. Do not

adjust the measuring force during a measurement process.

Force for external measurement PS16 V2 25mm

Force for internal measurement PS16 V2 50mm

Force for internal measurement PS16 V2 25mm

Force for external measurement PS16 V2 50mm

14 7

3.1. Description

1. Active reference

2. Measuring mode with 3-point function

3. Tolerance indicator

4. Multiplication factor

5. Sending data

6. Keypad lock

7. Hold measured value

8. 6-digit display

9. Tolerance mode

10. Preset Mode

11. Mode Min/Max/Delta

12. MODE menu indicator

13. Low battery

14. Indicator + / -

15. Measurement unit mm/INCH

16. Bluetooth® connection

3. Measurement unit

216

SET

MODE

3.1.1 Operating features of the instrument

- The instrument has two operating modes: basic functions (direct access)

and advanced functions. In addition to the conguration functions, 2

working reference functions can be accessed, in MIN, MAX and DELTA

(TIR) mode, plus tolerance display or input of multiplication factor other

than 1:1 (see chaps. 3.3 and 3.4)

- The «favourite» key gives direct access to the function used most often

(see chap. 3.6)

- Sets a Preset value, reset the MIN/MAX mode, veries a selection, and

controls switching off the instrument. By default, SIS mode enables

automatic switch-off with no loss of origin (see chap. 6)

3.1.2. Personalising the functions

It is possible to activate or deactivate certain functions of the instrument.

(requires a connection, see chap. 6.2)

3.1.3. Data transmission parameters

4800Bds, 7 bits, even parity, 2 stop bits

3.2. Start, re-initialisation

Press a button.

When the instrument is used for the rst time after the battery has been

changed or after it has been completely switched off (OFF), the instrument

needs to be reinitialised (--rEF-- ). Simply insert the measuring spindle to

the end of its travel.

For a Bluetooth®connection (see chap. 4).

MODE

3.3. Basic functions

Each short press on gives direct access to the basic functions :

MODE

SET

MODE

SET

MODE

bt rESEt MAC

SET

MODE

rEf.. Choice of reference (REF1 or REF2)

MODE

SET

Note :

It is possible to assign a different preset value to each of the 2 References. Similarly,

different tolerance limits can be assigned to References 1 and 2.

MODE

SET

MODE

SET

MODE

SET

MODE

SET

OFF On

MODE

3.4. Advanced functions

Prolonged pressure (>2s) on gives access to the advanced functions.

Then, each short press on accesses the required function :

ModE Minimum, Maximum and Delta (TIR) measurement

toL Tolerance display

(inputting tolerance limits, see chap. 3.5)

bt Bluetooth®ON/OFF or MAC address display

PrE...... Inputting a Preset value

next digit 0...9 save the PRESET

MODE

SET

MODE

bt rESEt MAC

SET

MODE

SET

MODE

SET

bt,CFG HId

PAIr

SIMPLE

SET

MODE

3.5. Inputting tolerance limits

To input or modify the tolerance limits, tol → On mode should be selected, followed

by a short press on

MODE

3.4. Advanced functions (continuation)

Unit . Units selection (mm or Inch)

rES Choice of resolution (depending on version)

dir Choice of measurement direction (positive or negative sense)

MuLt Inputting a multiplication factor other than 1.0000

Next digit 0...9 save MULT

OFF Automatic switch-off mode

MAn = de-activated, Auto = active

bt.CFG Bluetooth® prole selection (depending on model).

(see chap. 4 for details)

The + sign indicates the currently active prole.

Loc Keypad lock. Only the favourite key remains active

(to unlock the keypad, press for 5 sec)

3Pts Diameter measurements at 3 points (for 3 points version)

SET

MODE

SET

MODE

SET

3Pts

On Off

OnOFF

rESEt MAC

SET

MODE

SET

bt,CFG HId

PAIr

SIMPLE

SET

MODE

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Sylvac Instrument de mesure

Sylvac

Sylvac S Dial WORK Smart Manuel utilisateur

Sylvac

Sylvac S Mike PRO Manuel utilisateur

Sylvac

Sylvac Hi Cal Manuel utilisateur

Sylvac

Sylvac PS15 Manuel utilisateur

Sylvac

Sylvac SYLVAC-SCAN S145 Manuel utilisateur

Sylvac

Sylvac 810.9707 Manuel utilisateur

Sylvac

Sylvac Fowler Ultra-cal II Manuel utilisateur

Sylvac

Sylvac S Dial WORK Manuel utilisateur

Sylvac

Sylvac SCAN 52 Manuel utilisateur

Sylvac

Sylvac SYLVAC-SCAN S145 XL Manuel utilisateur

Sylvac

Sylvac D104-PC Manuel utilisateur

Sylvac

Sylvac SCAN F60 Manuel utilisateur

Sylvac

Sylvac S Mike PRO Smart Manuel utilisateur

Sylvac

Sylvac Bowers XTL Manuel utilisateur

Sylvac

Sylvac EVO Bluetooth Manuel utilisateur

Sylvac

Sylvac Hi Gage ONE Smart Manuel utilisateur

Sylvac

Sylvac SCAN F60 Manuel utilisateur

Sylvac

Sylvac S Dial Mini Manuel utilisateur

Sylvac

Sylvac UL 4 Manuel utilisateur

Sylvac

Sylvac SYLVAC-VISIO 300 GL Manuel utilisateur

Sylvac

Sylvac S Dial WORK ANALOG NANO Smart Manuel utilisateur

Sylvac

Sylvac S25 Manuel utilisateur

Sylvac

Sylvac Hi Cal Manuel utilisateur

Sylvac

Sylvac S_Cal EVO Smart Form E Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur