Swann NVW-600CMB Manuel utilisateur

Wi-Fi Battery-Powered

Security Camera

2K HD for Wi-Fi NVRs

Instruction Manual

Security Made Smarter

Introduction

Congratulations on the purchase of your Swann Wi-Fi

Battery-Powered Security Camera.

• 2K HD video transmitted wirelessly to NVR

• Battery-powered for ultimate convenience

• Controllable sensor spotlight & siren

• 2-way audio to welcome visitors or warn intrud-

ers

• True Detect™ heat & motion sensing for reli-

able alerts

• Powerful Night2Day™ color night vision

Important instructions

1. Make sure the camera is fixed correctly and stable

if fastened in place.

2. Never place strain of any kind on the power con-

nection and/or power adapter (if applicable).

3. Do not operate if wires and terminals are exposed.

Important Note: All jurisdictions have specific laws

and regulations relating to the use of cameras. Be-

fore using any camera for any purpose, it is the buy-

er’s responsibility to be aware of all applicable laws

and regulations that limit the use of cameras.

About this Manual: The content in this manual is for

information purposes only and is subject to change

without notice. While every effort is made to ensure

that this manual is accurate at the time of printing,

no liability is assumed for any errors that occurred.

For instructions on how to configure your camera

for motion detection, changing image settings,

and other functions available, please consult the

manual for your NVR. Go to support.swann.com,

search for your model, then download.

1. Charge the battery with the included

USB cable. Follow the illustration on

the left for connection (power adapter

not included). Charge the battery for

about 30 mins, then disconnect.

2. Insert the battery into the camera

(it will click into place). After a short

moment, you will hear a beep sound.

3. Leave the antenna in a vertical

position for the best reception.

Remove the plastic film from the

camera’s lens.

4. Follow the instructions in step 3 to

pair the camera to your NVR.

Charging the Battery2

2 3

Pair Button

IR LED

A. Remove the battery cover to access the USB-C connection.

B. Charge the battery using a power adapter included with your mobile

device.

C. Remove the plastic film from the camera’s lens.

Pairing the Camera3

1. In Live View mode, click a channel to pair the camera to.

2. A pair button appears (a blue pair button may also appear in the top-right hand corner of each channel).

Press this button to commence pairing. A message will appear on-screen.

3. Press and hold the pair button on the camera for 5 seconds, then release. The camera will commence pair-

ing, and the camera’s IR LED will start flashing.

4. After a short moment the camera will be paired, and you will see the camera’s image on-screen. If the cam-

era fails to pair, repeat the above instructions and try again.

Channel 2 28/04/2021 01:14:41 PM

Channel 3 28/04/2021 01:14:41 PM Channel 4 28/04/2021 01:14:41 PM

Press the pair button to

commence pairing.

The camera can be mounted onto a flat surface

using the screws and wall plugs provided. The

surface must have sufficient strength to hold

the camera.

1. Unscrew the mounting plate anti-clockwise

to remove it from the mounting bracket.

2. Position the mounting plate in the location

you want to mount it. Then, using the appropri-

ate screws for the surface you are mounting to,

secure the mounting plate in place.

3. Screw the mounting bracket to the rear of

the camera (as illustrated). Don’t overtighten

the bolt, as you will need to adjust the viewing

angle. Screw the mounting bracket onto the

mounting plate.

4. Adjust the camera to the desired viewing an-

gle, then tighten the bolt to secure it in place.

Mounting the Camera4

1 2

3 4

Bolt

Mounting Bracket

1. Take into consideration what you want to monitor

and where you’ll get the best view of it.

2. How you’re going to connect the camera to your

monitoring system; remember that cables and con-

nections should be kept out of the weather.

3. How to keep the camera out of harm’s way. It’s

recommended to mount your camera at an elevated

position.

4. Place your camera as close to the area of inter-

est as practicable. The best position is from about

13ft/4m above looking slightly down, keeping in mind

the details you are looking for.

5. Although the sky looks nice when you look at the

live view from your camera, it is an unlikely direction

for an offender to approach. Make sure your camera

has minimal sky in it as the light in daylight can make

the foreground of the image darker.

6. Think about the most likely way a potential offend-

er may approach your home, use your camera to give

you the best coverage of these areas.

7. The camera’s casing is resistant to different weath-

er conditions and tampering. It would take an over-

whelming event to damage the housing.

8. Even though the camera is weather and water-

resistant, prolonged exposure to adverse weather

conditions such as sunlight or excessive moisture,

may eventually damage the internal components of

the camera and adversely affect its performance.

9. Run cables inside a wall cavity or other protected

enclosure, and ensure that all wiring and connectors

are insulated and protected from moisture.

10. Don’t put your cable near live electrical wiring. AC

electricity generates radio “noise” which can inter-

fere with the signal from your camera.

Camera Location Tips5

Table des matières

Autres manuels Swann Système de sécurité

Swann

Swann 2K Series Manuel utilisateur

Swann

Swann DVR4-1000 Manuel utilisateur

Swann

Swann Alert DVR Camera Kit Manuel utilisateur

Swann

Swann RL-0507A Manuel utilisateur

Swann

Swann DIY Security Kit Manuel utilisateur

Swann

Swann 4 CCTV Cameras Security Monitoring System Manuel utilisateur

Swann

Swann SW347-WA2 Manuel utilisateur

Swann

Swann Alpha D04C1 Manuel utilisateur

Swann

Swann NVK-460 Manuel

Swann

Swann SWA44-D1C2M1 Manuel utilisateur

Swann

Swann PRO-530 Manuel utilisateur

Swann

Swann SW344-DPS Manuel utilisateur

Swann

Swann DEFEND & DETER SWA43-D12C16 Manuel utilisateur

Swann

Swann Advanced SWDVK-825504TB Manuel utilisateur

Swann

Swann DVR9-4200 Manuel utilisateur

Swann

Swann PLATINUM HD Manuel utilisateur

Swann

Swann DVR4-1200 Manuel utilisateur

Swann

Swann SW347-WAK Manuel utilisateur

Swann

Swann DVR16-8600 Combo Manuel utilisateur

Swann

Swann DVR4-4550 Manuel utilisateur

Swann

Swann SW276-ASL Manuel utilisateur

Swann

Swann 960H Pro series Manuel utilisateur

Swann

Swann SWNVK-874004-UK Manuel utilisateur

Swann

Swann PRO-580 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur

DSC

DSC PC 4010 Manuel du propriétaire