SURE-FI Relay PRO Bridge Manuel utilisateur

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Operators Manual

Doc #PI0257 Rev 1.0

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Quick Startup

The two units that are packaged together are factory paired and will only

communicate with each other.

Check initial operation

Connect a9V battery (not included) to the 9V cable (included) and plug the two-position connector into the

‘+VIN’and ‘-VIN’ positions on the bottom edge connector. Once both units are powered up, the green POWER

LED should be ON steady on each unit.Momentarily press the ‘TEST’button on either unit to test

communication between the two units. One or more of the blue Signal Strength LEDs should light up for one

second to indicate that successful communication hasoccurred between the two units.

Perform aRange-Test from the desired install locations

With the 9V batteries plugged in to each of the units, place them at the desired install location pointsand

perform aRange-Test by momentarily pressing the ‘TEST’ button. The received signal strength is displayed for

one second on the six blue LEDs with the bottom blueLED indicating the minimum signal strength and all six

LEDs indicating maximum signal strength.

Connect to permanent power

Connect the desired permanent powersource at each unit and perform several Range-Tests to check for

adequate input power.

Wire the input and output functions

Wire the desired devices at each unit.

The maximum voltage that can be applied to any of the

relay inputs(R1AIN – R8AIN / R1BIN –R8BIN)is 5VDC. A

dry contact closure or a 0 to 5VDC digital interface are

acceptable.

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Table of Contents

Part Numbers Pg. 5

Overview Pg. 5

Key Features Pg. 5

General Specifications Pg. 6

Radio Transceiver Specifications Pg. 6

Device Overview, Relay PRO UNIT A

Device Overview, Relay PRO UNIT B

Pg. 7

Pg. 8

UNIT A – Top &Bottom Connector pin descriptions Pg. 9 - 10

UNIT B – Top &Bottom Connector pin descriptions Pg. 11 - 12

Relays Pg. 13

The Test Push Button (Range Test) Pg. 13

Connector plug part number information Pg. 13

Chain Multiple system pairs for extended range Pg. 13

Mounting Pg. 14 – 15

Sure-Fi App –downloading, installing, connecting Pg. 16

Sure-Fi App –Firmware Updating Pg. 16

Sure-Fi App –Setting System Heartbeat, Relay Defaults and Timeout Pg. 17

Setting arelay as an RF-Link /Alert Relay Pg. 17

Troubleshooting Pg. 18

FCC and Industry Canada Regulatory Statements Pg. 19

Warranty Pg. 20

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Figure Reference Guide

Figure 1: Device Overview, UNIT A Pg. 7

Figure 2: Device Overview, UNIT B Pg. 8

Tables 1 and 2: Top Edge UNIT A ConnectorsP1 and P2 Pg. 9

Tables 2and 3: Bottom Edge UNIT A Connectors P3 and P3 Pg. 10

Tables 1 and 2: Top Edge UNIT B ConnectorsP1 and P2 Pg. 11

Tables 3 and 4: Bottom Edge UNIT B Connectors P3 and P4 Pg. 12

Figure 3: DIN Clips used for screw mount Pg. 14

Figure 4: DIN clip screw mount option top clip Pg. 15

Figure 5: DIN clip screw mount option bottom clip Pg. 15

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Part Numbers

DS010-RELAYPRO Relay PRO Bridgesystem: includes 1ea. SFI-RP601-01 &SFI-RP602-01

SFI-RP601-01 Relay PRO UNIT A

SFI-RP602-01 Relay PRO UNIT B

Overview

The Sure-Fi DS010-RELAYPRO system consists of two factory paired units that are ready to use with no

configuration required. TheRelay PRO UNIT A Interface wires to the Control Panel and communicates

wirelessly to the Relay PRO UNIT B Interface, which is placed out at the peripheral and any relay/switch

activated device. The Sure-Fi App provides for configuration, diagnostics,andfield firmware updates.

Key Features

Includes complete wireless solution for up to eight relay activated devices on each unit

Range: up to 1mile through obstructions and greater than 50 miles line-of-sight

Relays: seven FORM Cand one FORM Arelays on each unit

Chain multiple system pairs for extended range

DIN rail mount or direct wall mount

Sure-Fi App connects via Bluetooth for diagnostics and firmware updates

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

General Specifications

Operating Voltage: 12 to 30VAC/DC

Operating Current (@ 24VAC): 0.02A (idle), 0.26A(transmit)

Operating Power (@ 24VAC): 6.3VA (peak)

Relay Inputs (R1IN –R8IN): Dry contact or digital 0to 3.3VDC/5.0VDC interface

Relays 1 & 2: Two Form CMechanical Relays, 5A 220VDC /250VAC

Relays 3 – 7: Five Form Csolid state relays, 2A 30VDC /30VAC

Note: Maximum allowable combined current is 3A

Relay 8: One Form Asolid state Relay, 0.75A 30VDC / 30VAC

Range: Up to 1mile through obstructions. Greater than 50 miles line-of-sight

Can chain multiple system pairs for extended range

Encryption: AES128

Operating Temperature: -40°F to +158°F (-40°C to +70°C)

Storage Temperature: -67°F to +257°F (-55°C to +125°C)

Humidity: 0to 85% non-condensing

Dimensions (L x W x H): 3.54” x 5.30” x 1.28” (90mm x 135mm x32.5mm)

DIN mount type: 35mm DIN rail (DIN46277-3) /(DIN35)

Degree of Protection: IP20 to IEC/EN 60529

Radio Transceiver Specifications

Transmit Power: 1Watt (30dBm)

Frequency Band: 902 –928MHz

Channels:72 (FHSS)

Receiver Sensitivity: -133dbm

Link Budget: 163dB

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Device Overview

Figure 1: Overview,Relay PRO UNIT A Interface

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Device Overview

Figure 2: Overview, Relay PRO UNIT B Interface

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Relay Pro UNIT AInterface connectors

Table 1: Top Edge UNIT A connector P1. See Figure 1for connector location and pin numbers

CONNECTOR

OSITION

NAME

DESCRIPTION

P1 1R2ANC Relay 2A Normally-Closed terminal

P1 2 R2ACOM Relay 2A Common terminal

P1 3 R2ANO Relay 2A Normally-Open terminal

P1 4 GND Ground

P1 5 R2BIN Relay 2UNIT BInput

P1 6 GND Ground

Relay

UNIT

Input

P1 8 R1ANC Relay 1A Normally-Closed terminal

P1 9 R1ACOM Relay 1A Common terminal

P1 10 R1ANO Relay 1A Normally-Open terminal

Table 2: Top Edge UNIT A connector P2. See Figure 1for connector location and pin numbers

CONNECTOR

OSITION

NAME

DESCRIPTION

P2 1 R4A NC Relay 4A Normally-Closed terminal

P2 2 R4A COM Relay 4A Common terminal

P2 3 R4A NO Relay 4A Normally-Open terminal

P2 4 GND Ground

Relay

UNI

Input

P2 6 GND Ground

P2 7 R3B IN Relay 3UNIT BInput

P2 8 R3A NC Relay 3A Normally-Closed terminal

P2 9 R3A COM Relay 3A Common terminal

P2 10 R3A NO Relay 3A Normally-Open terminal

SURE-FI, INC. |www.sure-fi.com

Sure-Fi Relay PRO Bridge

Relay Pro UNIT Aconnectors (cont.)

Table 3: Bottom Edge UNIT A connector P3. See Figure 1for connector location and pin numbers

CONNECTOR

OSITION

NAME

DESCRIPTION

P3 1+VIN +VDC input or VAC input

P3 2 -VIN -VDC input or AC common input

R8A

Relay

Normally

Open

terminal

P3 4 R8A COM Relay 8A Common

P3 5 R8B IN Relay 8B UNIT BInput

P3 6 GND Ground

P3 7 R7B IN Relay 7B UNIT BInput

P3 8 R7A NC Relay 7A Normally-Closed terminal

P3 9 R7A COM Relay 7A Common terminal

R7A

Relay

Normally

Open

terminal

Table 4: Bottom Edge UNIT A connector P4. See Figure 1for connector location and pin numbers

CONNECTOR

OSITION

NAME

DESCRIPTION

P4 1R6A NC Relay 6A Normally-Closed terminal

P4 2 R6A COM Relay 6A Common terminal

P4 3 R6A NO Relay 6A Normally-Open terminal

GND

Ground

P4 5 R6B IN Relay 6UNIT BInput

P4 6 GND Ground

P4 7 R5B IN Relay 5UNIT BInput

R5A

Relay

Normally

Closed

terminal

P4 9 R5A COM Relay 5A Common terminal

P4 10 R5A NO Relay 5A Normally-Open terminal

Ce manuel convient aux modèles suivants

Table des matières

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur