Suntex TC-7100 Manuel utilisateur

EnterMode

Cal.Setup

HI B.L. WASH LO

S/N:0811001001

Turbidity TRANSMITTER TC-7100

Operation

Manual

TC-7100

Microprocessor

Turbidity/S.S.

Transmitter

Brief Instruction 1

1. Specifications 6

2. Precautions for installation 7

3. Assembly and installation

3.1 Controller installation 7

3.2 Illustration of panel mounting 7

3.3 Illustration of Wall mounting and pipe mounting 8

4. Overview of Turbidity/Suspended Solids Transmitter TC-7100

4.1 Illustration of rear panel 9

4.2 Illustration of terminal function 9

4.3 Description of terminal function 10

4.4 Cable connection 10

4.5 Electrical connection diagram 11

5. Configuration

5.1 Illustration of front panel 12

5.2 Keypad 12

5.3 LED indicators 13

5.4 Display 13

6. Operation

6.1 Measurement mode 14

6.2 Set-up mode 14

6.3 Calibration mode 14

6.4 Reset 14

6.4.1 Master reset 14

6.4.2 Calibration reset 14

6.5 Time and date mode 14

7. Settings

Block diagram of settings 15

7.1 Entry of set-up mode 16

7.2 Security code of settings 16

7.3 Sensor model set-up 17

7.4 Measurement unit set-up 17

7.5 Hi point Setting 18

7.6 Lo point Setting 19

7.7 Automatic sensor scrub time interval set-up 20

7.8 Wash time 21

7.9 Analog output set-up 22

CONTENTS

7.10 Average signal transmission time set-up 23

7.11 Date/time set-up 23

7.12 RS-485 set-up 24

7.13 Backlight LCD 25

8. Calibration

Block diagram of Calibration 26

8.1 Security code of calibration 27

8.1.1 Authority of Security Code 27

8.1.2 Security Code Settings 27

8.2 Standard solution calibration—CT 28

8.3 Offset calibration—CA 30

9. RS-485

9.1 RS-485 wiring diagram 31

10. Error messages (Error code) 32

11. Maintenance 32

Brief Instruction

If you like to use security code of settings, the original code is 1111.

Settings of measurement parameters (see chapter 7)

In measurement mode, pressing “Setup＂and “Mode＂simultaneously

allows you to access Set-up mode.

Settings of Calibration (see chapter 8)

In measurement mode, pressing “Cal.＂and “Mode＂simultaneously

allows you to access Calibration mode.

In the Code function, entering original code or user’s designated code allows you to

reset the code or shut down this function.

If you like to use security code of calibration, the original code is 1111.

In the Type function, please select a model type of sensor.

In the Code function, entering original code or user’s designated code allows you

to reset the code or shut down this function.

In the Configuration function, there is no function.

In the Relay 1 function, please select or to activate it or not.

In the Relay 2 function, please select or to activate it or not.

In the Clean function, please set wash time and stop duration.

In the Out function, please set analog output with or

In the Scrub function, please set sensor lens scrub time interval.

In the Unit function, please select correlated measurement unit.

In the Second function, please set average measurement reading time.

In the Serl function, please set MODBUS’s encoding, check bit, ID code and baud speed.

(

TC-7100RS onl

In the Back light function, please set brightness of display and sensitivity of

light-source sensor.

In the Real time clock function, please set year, date, and time. (TC-7100RS only)

Note: “Ct 1” must be 0 NTU standard solution calibration.

Recommendation: Do not calibrate the value over 80% of measurement full scale.

進入模擬訊號顯示，等待數值顯示穩定後按鍵，

開始校正。

4. The display shows Ct2 for entering the second point calibration.

Clean the sensor before immersing it into well-prepared standard

solution. Constantly stir the solution. Press to confirm it.

Enter turbidity range selection.

1. Enter CT1 Calbration mode. After cleaning up the sensor,

inmmerse the sensor into 0.00 NTU standard solutioin. Press

to confirm it. The display shows “0.00NTU”. Continually

press to send the calibration signal to sensor.

5. Enter turbidity range selection, press or to select

suitable range. Press and the value starts to twinkle. Press

or to adjust value until it is the same with the standard

solution’s value. Press to display the analog signal of the

sensor.

Two or up to five points calibration, and in which “Ct 1” must be 0 NTU calibration.

Offset calibration.

Turbidity standard solution 2 to 5 point calibration

2. At the time, the sensor responses 2 mA analog signal to indicate

that the sensor is in the process of inner calibration.

3. After inner calibration of the sensor, it responses 4 mA analog

signal to transmitter. Press to calibrate the sensor with the

0.00 NTU standard solution.

1. 螢幕顯示 CT4進入第四點校正，步驟同 4~6。

注：於顯示 CT4介面時按鍵可以完成 3點

校正。直接跳至步

2. 螢幕顯示 CT5進入第五點校正，步驟同 4~6。

注：於顯示 CT5介面時按鍵可以完成 4點

校正。直接跳至步驟 10。

7. The display shows Ct3 for entering the third point calibration. The

procedure is the same as step 4~6.

Note: To finish the calibration procedure as a two point

calibration, when the display shows Ct3 please press and

skip to step 10.

6. Enter analog signal display. Wait until the signal becomes stable,

then you may start the calibration.

8. The display shows Ct4 for entering the forth point calibration. The

procedure is the same as step 4~6.

Note: To finish the calibration procedure as a three point

calibration, when the display shows Ct4 please press and

skip to step 10.

3. 校正成功時，螢幕出現 CAL PASS 字樣，校正失

敗時，出現 CAL Err 訊息。(請參閱第十章錯誤訊

息，尋求原因及處理方法)

9. The display shows Ct5 for entering the fifth point calibration. The

procedure is the same as step 4~6.

Note: To finish the calibration procedure as a four point

calibration, when the display shows Ct5 please press and

skip to step 10.

10. When the calibration is successful, the display screen shows the

word “CAL PASS”; when the calibration is unsuccessful, the

display screen shows the word “CAL Err”. (Please refer to chapter

10 for error message, causes and treatment seeking.)

OffsetCalibration

註：執行偏移值校正前必須作過ㄧ次標準液校正後方可

執行偏移值校正。

Reset

Note: Before the implementation of offset calibration,

it is necessary to make a 2 to 5 points standard

solution calibration in advance.

4. When the calibration is successful, the display screen shows the

word “CAL PASS”; when the calibration is unsuccessful, the

display screen shows the word “CAL Err”. (Please refer to

1. After entering into display CA, put the sensor which has been

cleaned into turbidity standard solution, and constantly stir the

solution. Press to confirm and enter into turbidity range

selection.

2. Enter turbidity range selection and press or to

select suitable range. Press . At the time, the display value

starts to twinkle, then press to enter analog signal display.

3. Enter analog signal display. Wait until the display value

becomes stable. Press to starts calibration.

Press for 5 seconds, then press . The display will show to indicate

that the “Master Reset” has been done.

Press for 5 seconds, then press . The display will show to indicate

that the “Calibration Reset” has been done.

＋

1.Specifications

Model TC-7100 TC-7100RS

Measuring mode Turbidity / Suspended Solids

Measuring unit TURB: NTU, FTU, FNU

SS: ppm, mg/l

Measuring range Depend on which sensor as below

Resolution AUTO( 0.001 / 0.01 / 0.1 / 1)

Signal average

time 0∼60 sec. selectable/default 30 sec.

Ambient

temperature 0∼50°C

Display CD display with sensitization sensor for auto/manual illumination function

Analog output Isolated DC 0/4~20mA corresponding to Turb/SS, max. load 500Ω

Serial interface - RS485(MODBUS RTU or MODBUS

ASCII)

Contact Relay ON/OFF, 240VAC, 0.5A Max.

Setting Active Hi/Lo two limited programmable

Contact 240VAC, 0.5A Max.

Wash Active ON: 0~9999 sec. / OFF: 0.0~999.9 hours

Voltage output DC±12V

Power supply 100V∼240VAC±10%，50/60Hz

Installation Wall or Pipe or Panel mounting

Dimensions 144 mm ×144 mm ×115 mm (H×W×D)

Cut off dimensions 138 mm ×138 mm (H×W)

Weight 0.82Kg

Certification IP 65 (NEMA 4)

Sensor Model No. TC-100 TC-500 TC-3000 TCS-1000

Measuring range 0.00-20.00NTU or

20.1-100.0NTU

0.0-200.0NTU or

201-500 NTU 0-3000NTU 0-1000ppm

Cleaning system Auto scrub cleaning upon power on

Time interval for

cleaning

1~9 min, user

selectable / Default

30 min.

1~9 min, user selectable / Default 10 min

Ambient

temperature 0-40°C

Wet part SUS 316L,Sapphire glass, Fluorocarbon rubber, EPDM,POM

Dimensions Φ32×163mm

Weight Approx. 930g

Protection degree IP68

Cable length 10m

Accuracy ±3% of full scale

Repeatability ±2% of full scale

Installation Immersion in open tank

Wrong wiring will lead to breakdown or electrical shock of the instrument, please read this

operation manual clearly before installation.

zMake sure to remove AC power from the controller before wiring input, output connections,

and remove it before opening the controller housing.

zThe installation site of the controller should be good in ventilation and avoid direct sunshine.

zThe material of signal cable should be special coaxial cable. Strongly recommend using our

coaxial cable. Do not use normal wires instead.

zAvoid electrical surge when using power. Especially when using three-phase power, use

ground wire correctly.

3.Assemblyandinstallation

3.1 Controller installation: This controller can be installed through panel mounting, wall

mounting and pipe mounting.

Installation of panel mounting: First,prepare a square hole of 138 x 138mm on the panel box,

and then insert the controller directly into the panel box. Insert the accessorial mounting

bracket from the rear, and make it be fixed in to pickup groove.

3.2 Illustration of panel mounting:

2. Precautions for installation

138mm

138m

Hole size

42mm

＋

42mm

Hole distances on the

anel box

Mounting bracket

Illustration of panel mounting,

fixed with Mounting bracket

Table des matières

Autres manuels Suntex Émetteur

Suntex

Suntex EC-4110 Manuel utilisateur

Suntex

Suntex TC-7310-RS-M Manuel utilisateur

Suntex

Suntex CT-6300 Manuel utilisateur

Suntex

Suntex PC-3110-P Manuel utilisateur

Suntex

Suntex PC-3310 Manuel d'installation

Suntex

Suntex CT-6300RS Manuel utilisateur

Suntex

Suntex PC-3110-RS Manuel utilisateur

Suntex

Suntex IT-8100 Manuel utilisateur

Suntex

Suntex TC-7310-RS Manuel utilisateur

Suntex

Suntex EC-4110-I Manuel utilisateur

Suntex

Suntex CT-6110-POL Manuel utilisateur

Suntex

Suntex PC-300A Series Manuel utilisateur

Suntex

Suntex PC-3310-RS Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur