Sub-Zero 601R Manuel utilisateur

600

INSTALLATION GUIDE

600

SERIES

INSTALLATION GUIDE

600

SERIES

Before you begin your installation of a Sub-Zero 600 Series

unit, there are a few things you should take special care to

observe. By reading these introductory instructions careful-

ly, you will make the installation procedure easier, problem-

free and, most important, safe.

First, as you follow these installation instructions, take par-

ticular note of the WARNING! and CAUTION! symbols

when they appear. This information is important for the safe

and efficient installation of this Sub-Zero.

Also, The printed instructions may signal an IMPORTANT

NOTE,which highlights information that is especially

important for a problem-free installation.

Second, make sure that the actual equipment that was

shipped to you matches the design you are expecting to

install. Sub-Zero 600 Series models offer the following

design alternatives: Framed, Overlay, Glass Door Models

and Stainless Steel which is available in three finishes:

classic, platinum and carbon stainless steel.

Each of these design options has specific installation

requirements, which means it is vital that the unit match

your planning and space needs. Before you begin, check the

exact model number you need against the model numbers

on the shipping carton.

•Stainless steel units (classic, platinum and carbon finish-

es) are packed in cartons with a gray cap and white letter-

ing identifying them as stainless steel. The stainless steel

unit will have a wrapped door, 1" (25) diameter handles

and heavy-duty stainless steel louvered grille.

•Framed units are packed in cartons with a white cap and

blue lettering identifying them as framed. The framed unit

will have an extruded handle and a louvered grille.

•Overlay units are packed in cartons with a blue cap and

white lettering identifying them as overlay. The unit is

shipped with no handle hardware (hardware is supplied at

the site to match cabinetry at the installation) and a two-

part panel grille frame without a panel.

If the unit you receive does not match your requirements,

contact your Sub-Zero dealer.

Please note, this 600 Series installation guide also covers

procedures for the installation of the Model 561.

WARNING

alerts you to a hazard that may cause serious injury or

death if precautions are not followed.

CAUTION

signals a hazard where minor injury or product damage

may occur if you do not follow instructions.

600

SERIES

INSTALLATION GUIDE

PREPARING THE SPACE

Step 1: First, make sure that the opening where the

Sub-Zero is to be installed is properly prepared. Refer to the

Pre-Installation Specifications illustrations and chart to be

sure the space dimensions, electrical service and plumbing

are correct for the model you are about to install.

Step 2: If you are installing units side by side, a separating

filler strip is recommended. Add the filler strip width to the

finished rough opening dimension. Complete the installa-

tion with Anchoring Kit (part #4200900), see page 17.

IMPORTANT NOTE: To operate properly, the door must

open a minimum of 90˚. Use a minimum 3" (76) filler in cor-

ner installations to assure a 90˚ door opening.Allow enough

clearance in front of the unit for full door swing.

IMPORTANT NOTE: Make sure the floor under the refrig-

erator is level with the surrounding finished floor. Protect a

finished floor with plywood, cardboard or some other suit-

able material before moving the refrigerator across it.

600

SERIES

PRE-INSTALLATION SPECIFICATIONS

MODELS 601R, 601RG AND 601F

723/4"

(1848)

ROUGH

OPENING

HEIGHT

723/4"

(1848)

MINIMUM

HEIGHT

REQUIRED

(LEVELERS IN)

24"

(610)

ROUGH

OPENING

DEPTH

11"

(279)

(76)

24"

(610)

LOCATE WATER SUPPLY

WITHIN BOTTOM SHADED

AREA ONLY (601F ONLY)

LOCATE ELECTRICAL

WITHIN ENTIRE SHADED AREA

(152)

SHUT-OFF

VALVE

EXTEND WATER LINE

APPROX. 36" (914)

FROM BACK WALL

(601F ONLY)

ROUGH OPENING WIDTH

FRONT VIEW

TOP VIEW

Finished Rough Minimum Door

Opening Width (A) Clearance (B)

Model 601R

"(902) 36

"(916)

Model 601RG

"(902) 36

"(916)

Model 601F

"(902) 36

"(916)

NOTE: Dimensions in parentheses are in millimeters.

Dimensions in parentheses are in millimeters unless otherwise specified.

600

SERIES

PRE-INSTALLATION SPECIFICATIONS

Finished Rough Minimum Door

Opening Width (A) Clearance (B)

Model 611

"(749) 30

"(765)

Model 611G

"(749) 30

"(765)

Model 650

"(902) 36

"(916)

Model 650G

"(902) 36

"(916)

Model 561

"(902) 20

"(527)

Model 661

"(902) 20

"(527)

Model 642

"(1054) 25

"(649)

Model 680

"(1054) 25

"(649)

Model 685

"(1054) 25

"(649)

Model 632

"(1207) 29

"(743)

Model 690

"(1207) 29

"(743)

Model 695

"(1207) 29

"(743)

NOTE: Dimensions in parentheses are in millimeters.

833/4"

(2127)

ROUGH

OPENING

HEIGHT

WITH

STANDARD

11" (279)

GRILLE

827/8"

(2105)

MINIMUM

HEIGHT

REQUIRED

(LEVELERS IN)

751/2"

(1918)

(178)

(152)

ROUGH OPENING WIDTH

24"

(610)

ROUGH

OPENING

DEPTH

(76) 18"

(457)

LOCATE WATER SUPPLY

WITHIN SHADED AREA

LOCATE ELECTRICAL

WITHIN SHADED AREA

(152)

SHUT-OFF

VALVE

EXTEND WATER LINE

APPROX. 36" (914)

FROM BACK WALL

FRONT VIEW

TOP VIEW

237/8"

(606)

BEHIND

FRAME

3/8"(10)

FRAME

EXTENSION

90˚

237/8"

(606)

BEHIND

FRAME

3/8"(10)

FRAME

EXTENSION

90˚

Models 601R, 601RG, 601F,

611, 611G, 650 and 650G

Models 561, 661, 642, 680, 685,

632, 690 and 695

MODELS 611, 611G, 650, 650G, 561,

661, 642, 680, 685, 632, 690 AND 695

MINIMUM DOOR CLEARANCE AT 90˚

PREPARING ELECTRICAL

CONNECTIONS

Step 3: To prepare the electrical system, rough in the elec-

trical outlet following the Pre-Installation Specifications.

You will need a 115 volt, 60 Hertz electrical supply. Dedicate

a separate 15 amp fuse or circuit breaker to the Sub-Zero

unit, and follow any local codes that apply.

The Sub-Zero unit comes with a power supply cord with a

three-prong grounding plug. The refrigerator must be

plugged into a mating three-prong wall receptacle ground-

ed in accordance with the National Electrical Code and local

codes.

PREPARING PLUMBING

CONNECTIONS

Step 4: For units with automatic ice makers, first rough in

the water supply line. Connect a 1/4" copper line to the

house supply. Use an easily accessible shut-off valve

between the supply and the refrigerator. This is usually

about 6" (152) from the compression fitting. The ice maker

operates on water pressure of 20 psi (1.4 bar) to 100 psi

(6.9 bar).

If the local water supply has high levels of sediment, con-

sider adding an in-line filter. But don’t use a self-piercing

valve. See your Sub-Zero dealer for a saddle valve kit, ask

for part number 4200880.

Good water is important for good ice quality. It is not rec-

ommended that the ice maker be connected to a softened

water supply. Water softener chemicals, such as salt from a

malfunctioning softener, can damage the ice maker mold

and lead to poor ice quality. If a softened water supply can-

not be avoided, it is important that the water softener be

well maintained and operating properly.

Reverse osmosis systems can be used, provided there is a

consistent water pressure of 20 psi (1.4 bar) to 100 psi (6.9

bar) supplied to the water valve at all times.

Route the water line through the floor within 1/2" (13) from

the wall and no higher than 3" (76) from the floor. If the

water supply is brought in from behind the unit, route the

water line through the wall no more than 3" (76) from the

floor. In either case, allow at least 3' (1 m) of excess copper

tubing outside the wall or floor for easy connection to the

refrigerator.

WARNING

Do not use an extension cord, or two prong adapter.

Electrical ground is required on this appliance.

Do not under any circumstances remove the power sup-

ply cord ground prong.

600

SERIES

Dimensions in parentheses are in millimeters unless otherwise specified.

CAUTION

This outlet must be checked by a qualified electrician to

see if it is wired with the correct polarity. Verify that the

outlet provides 115 volts and is correctly grounded. If a

ground fault circuit interrupter (GFCI) circuit is used,

product operation interruptions may occur.

For Models 601R, 601RG and 601F (stainless steel), the

lower grille snaps out by pulling forward on the bottom of

the grille.

If you’re installing overlay Models 611, 611G, 650, 650G,

561, 661, 642, 685, 632 and 695, first remove the inner

grille panel assembly, as shown in illustration 4. Lift up, then

pull out at the bottom, pull the top section down and out of

the top key slot. Next, remove the five mounting screws

that hold the outer grille panel assembly to the top com-

partment. See illustration 5.

UNPACKING THE SUB-ZERO

Step 5: Uncrate the unit, remove its wood base and discard

the shipping bolts that hold the wood base to the bottom

of the refrigerator. Remove all packing materials and tape

as well. Do not discard the kickplate. Also, do not discard

the anti-tip kit and hardware, because you may need them

to block your installation. Next, retract the front leveler legs

to let you move the unit more easily during installation.

To reduce the possibility of the unit tipping forward, posi-

tion the front levelers flat on the floor. Extend these legs

when the unit is finally positioned.

REMOVING THE GRILLE

Step 6: Remove the grille in order to get to the power cord

and move the unit through doorways. For framed and stain-

less steel Models 611, 611G, 650, 650G, 561, 661, 642, 680,

685, 632, 690 and 695, remove three counter-sunk grille

screws at the bottom of the grille and cut the red nylon

shipping strap. NOTE: Grille screws are accessed with

door(s) open. Then tilt the grille forward and release the

springs from behind the grille. See illustration 2.

For Models 601R, 601RG and 601F (framed and overlay),

remove the two black screws in the lowest louver in the

grille. Tilt the bottom of the grille out and away. It’ll release

from the top of the grille. See illustration 3.

Grille Springs

Grille

Screws

(inside door)

Illus. 2 Illus. 3

600

SERIES

WARNING

Keep door(s) and drawer(s) taped closed while moving

unit.

Illus. 4 Illus. 5

INNER

GRILLE PANEL

ASSEMBLY

1"(25)

SOFFIT

(76)

WOOD BLOCK

SHROUD

WALL STUD

SCREW

BLOCKING FOR SAFETY

Step 7: If there is a solid soffit above the unit with clear-

ance between the unit and the soffit of 1" (25) or less, you

won't need to block the unit. See illustration 6. But for

installations with clearances of more than 1" (25), you must

block the unit.

Use the anti-tip kit (wood block and hardware) provided

with the shipping crate. Locate and mark two wall studs

against the wall where the refrigerator will be located.

Next, locate the proper height to clear the unit. The space

between the unit top and the bottom of the wood block

must not be more than 1/4" (6).

Position the wood block over the unit and use the screws

and "L" brackets to lock it in place. Make sure the screws

extend a minimum of 7/8" (22) into each of the two wall

studs. Make sure the wood block extends at least 3" (76)

over the unit and is securely in place. Refer to illustration 7.

Using the front and rear levelers, raise the unit until it

makes contact with the wood block.

Make sure that the front levelers are firmly on the floor, to

reduce the possibility of the cabinet tipping forward.

IMPORTANT NOTE: If at all possible, keep door(s) closed

on the unit until it is properly anchored.

WARNING

To prevent the unit from tipping forward and provide a

stable installation, the unit must be secured in place

with an anti-tip device.

600

SERIES

Illus. 6

Illus. 7

Dimensions in parentheses are in millimeters unless otherwise specified.

Step 9: Now, level the unit.To adjust the height, turn the

front leveling legs counterclockwise to lower it. Adjust the

rear levelers from the front of the base. Turn the 5/16" hex

bolt clockwise to raise the cabinet, counterclockwise to

lower the cabinet. Refer to illustration 10. When the unit is

leveled properly, or squared off, door adjustments are less

likely to be necessary.

IMPORTANT NOTE: Be sure to reference leveling of the

unit to the floor and not to surrounding cabinetry, by using

the unit main frame and door trim as leveling reference

points. This could effect the operation of the unit, such as

door(s) not closing properly.

Step 10: After the unit has been leveled, install the kick-

plate as shown in illustration 11. Be sure the drain pan is

installed properly.

COMPLETING THE INSTALLATION

Step 8: To complete the installation, first shut off power

to the wall outlet.Plug into a 15 amp grounded outlet

and roll the unit into position under the wood block or sof-

fit. Now you have to connect the ice maker water line.

Remove the 1/4" compression fitting from its plastic bag

and join the water supply line to the solenoid valve.

If desired, the water valve can be removed from mounting

bracket to gain easier access to water connection, as shown

in illustration 8. Purge the line before making the final con-

nection. Illustration 9 applies only to Model 680 and 690.

IMPORTANT NOTE: Turn on the water supply and

check all fittings for leaks. Make certain the electrical

harness is attached to the solenoid.

In areas with water of high mineral content, the use of an

in-line water filter is recommended. Make sure the filter is

positioned and accessible for replacement when necessary.

IMPORTANT NOTE: Let your customer know that the

ice maker will not fill with water immediately, and

that the first three batches of ice produced should be

discarded. Allow 24 hours for proper ice production.

ELECTRICAL

CONNECTION

SOLENOID

VALVE

1/4" COPPER

SLEEVE

1/4" COMPRESSION NUT

FRONT

LEVELERS

REAR

ADJUSTMENT

CAUTION

Protect any finished flooring before moving the unit in

place. All full-size Sub-Zero models are equipped with

rollers, so you can easily move the unit into place. If for

any reason the unit has been laid on its back or side,

you must allow the unit to stand upright for a minimum

of 24 hours before connecting power.

WARNING

To reduce the possibility of the cabinet tipping forward,

the front levelers must be in contact with the floor.

CAUTION

The kickplate must be removed for servicing. The floor

cannot interfere with removal. Refer to label mounted

on kickplate support for height clearance.

Step 11: Replace the grille by reversing the procedure in

Step 6 and turn the power back on. If you’re using a panel

grille, refer to Installing Overlay Grille Panels, page 13.

600

SERIES

Illus. 8 Illus. 9

Illus. 10 Illus. 11

Step 14: With a Phillips screwdriver, remove the handles

from the freezer and refrigerator doors. Slide the panel into

the frame on the door. With the panel in position, replace

the handles. Be sure the panel is inserted completely into

the channel for proper fit and alignment. See illustration 13.

Next, replace the trim moldings by inserting the top, then

the bottom into the handle channel. Release the middle and

set the magnets.

INSTALLING PANELS

Before you begin installing panels, refer to the Panel

Specifications charts, and be sure you are working with the

Sub-Zero panel design called for in your installation plans.

If your customer has chosen the stainless steel design, the

unit has been shipped complete with a finished stainless

steel look. No panels or handle hardware are necessary to

install. In your final preparation for stainless steel units use

a stainless steel cleaner to remove any marks. Abrasive

cleaners should NOT be used, as they may scratch the sur-

face.

If your customer has ordered either framed or overlay units,

you will be installing panels to give the unit the custom

Sub-Zero look.

FRAMED PANELS

Step 12: If your customer has chosen a framed design

application, first remove the door handles to install the

front panels. The handle screws are hidden by a magnet

backed trim molding. Remove the molding using a piece of

tape to pull it away from the handle and expose the handle

screws. The molding will bend at the center so that you can

remove it. See illustration 12.

Step 13: If the thickness of the custom panels is less than

a 1/4" (6), back them up with a sheet of shim material to

build the total thickness to a 1/4" (6). If the panel is thick-

er than a 1/4" (6), rout an edge around the panel to get a

proper fit. Keep in mind that the weight of each panel can-

not exceed 50 lbs (23 kg). Refer to the Framed Panel

Specifications chart on page 12 for panel dimensions.

Additional panel design information can be found in the

Sub-Zero Design Guide.

IMPORTANT NOTE: On all models except Model 680 and

690, routing, recessing or optional extended handles may

be required on raised panels for finger clearance under the

handle. See Accommodations for Raised Panels, page 11.

600

SERIES

Illus. 12 Illus. 13

Dimensions in parentheses are in millimeters unless otherwise specified.

Autres manuels pour 601R

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sub-Zero Réfrigérateur

Sub-Zero

Sub-Zero BI-30U Instructions de montage

Sub-Zero

Sub-Zero 700BR Instructions de montage

Sub-Zero

Sub-Zero IC-27R Manuel utilisateur

Sub-Zero

Sub-Zero ID-24R Manuel utilisateur

Sub-Zero

Sub-Zero ICBBI-36R Manuel utilisateur

Sub-Zero

Sub-Zero INTEGRATED REFRIGERATION Manuel utilisateur

Sub-Zero

Sub-Zero ID-36RP Manuel utilisateur

Sub-Zero

Sub-Zero Designer Series Manuel utilisateur

Sub-Zero

Sub-Zero 648PRO Manuel utilisateur

Sub-Zero

Sub-Zero BI-30UG Manuel d'utilisation

Sub-Zero

Sub-Zero 500 Series Guide de configuration rapide

Sub-Zero

Sub-Zero PRO3650 Instructions d'installation

Sub-Zero

Sub-Zero BI-36R Manuel utilisateur

Sub-Zero

Sub-Zero DEC3650FI/R Manuel utilisateur

Sub-Zero

Sub-Zero Sub-Zero BI series Manuel de service

Sub-Zero

Sub-Zero IT-30RID Manuel utilisateur

Sub-Zero

Sub-Zero BI-36U Manuel utilisateur

Sub-Zero

Sub-Zero 700BCI Manuel utilisateur

Sub-Zero

Sub-Zero 600 Series BI-30UG Manuel utilisateur

Sub-Zero

Sub-Zero UC-24 series Manuel utilisateur

Sub-Zero

Sub-Zero UC-24B Manuel utilisateur

Sub-Zero

Sub-Zero 736TR Instructions de montage

Sub-Zero

Sub-Zero 601R Manuel utilisateur

Sub-Zero

Sub-Zero ICBBI-36F Manuel utilisateur

Manuels Réfrigérateur populaires d'autres marques

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manuel utilisateur

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manuel utilisateur

Sharp

Sharp SJ-BA31IEXW2-EU Manuel utilisateur

CORBERO

CORBERO CC2300MCW Manuel utilisateur

KitchenAid

KitchenAid 2205264 Manuel utilisateur

Stengel

Stengel KU 1101 A++ Manuel utilisateur

NEFF

NEFF KI181 Series Manuel utilisateur

Hoshizaki

Hoshizaki Reach-In Manuel utilisateur

Amana

Amana ASD2524VES00 Manuel utilisateur

BOMANN

BOMANN KGC 213 Manuel utilisateur

Danby

Danby DAR044A1SLDD Instructions de montage

Samsung

Samsung RF323TE Manuel utilisateur

Beko

Beko CSA31022 Manuel utilisateur

IKEA

IKEA FROSTIG C 185 E Manuel utilisateur

Electrolux

Electrolux ER 6821 D Manuel utilisateur

True

True TS-28 Manuel utilisateur

Frigidaire

Frigidaire FSC23R5DW9 Manuel utilisateur

Beko

Beko LSP4579W Manuel utilisateur