Strontech IMB-H114 Manuel utilisateur

IMB-H114

motherboard

IMB-H114 motherboard

Preface

This publication, including all photographs, illustrations and software, is protected under international

may be reproduced without written consent of the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-turer makes no

representations or warranties with respect to the contents hereof and specifically disclaims any implied

warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right

to revise this publication and to make changes from time to time in the content hereof without obligation

of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.

Other product names used in this manual are the properties of their respective owners and

are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

•Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to

ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications

not expressly approved by the system’s manufacturer could void the user’s authority to operate the

equipment.

INSTRUCTION

2 3

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following

conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that

may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing

Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel

brouilieur du Canada.

Aboutthe Manual

The manual consists of the following:

Describes features of the

motherboard.

Go to page 5

Describes installation of

motherboard components.

Go to page 13

Go to page 33

Chapter 2

Installing the Motherboard

Chapter 1

Introducing the Motherboard

Chapter 3

Using BIOS

Chatper 4

Trouble Shooting

Provides basic trouble shoot

ing tips

page 71

Go to

Provides information on using

the BIOS Setup Utility.

2retpahC 13

Installing the Motherboard 13

Safety Precautions......................................................................... 13

Choosing a Computer Case...........................................................13

Installing the Motherboard in a Case..........................................13

Checking Jumper Settings.............................................................14

Setting Jumpers......................................................................14

Checking Jumper Settings......................................................15

Jumper Settings......................................................................15

Installing Hardware...................................................................17

Installing the Processor.........................................................17

Installing Memory Modules...................................................20

Expansion Slots......................................................................21

Connecting Optional Devices.................................................23

Installing a SATA Hard Drive................................................26

Connecting I/O Devices............................................................... 27

Connecting Case Components.....................................................28

Front Panel Header................................................................31

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

1ecaferP

51retpahC

5draobrehtoMehtgnicudortnI

Introduction.................................................................................. 5

Feature........................................................................................... 6

Specifications................................................................................8

Motherboard Components........................................................10

333retpahC

33SOIBgnisU

About the Setup Utility........................ ......................................... 33

The Standard Configuration..................................................33

Entering the Setup Utility.........................................................33

Using BIOS......................................................................................34

BIOS Navigation Keys............................................................35

Main Menu.............................................................................35

Advanced Menu......................................................................36

Chipset Menu..........................................................................58

Security Menu..........................................................................65

Boot Menu..............................................................................66

Exit Menu...............................................................................69

Updating the BIOS...................................................................70

Chapter 4 71

17gnitoohSelbuorT

Start up problems during assembly.............................................71

Start up problems after prolong use...........................................72

Maintenance and care tips.............................................................72

Basic Troubleshooting Flowchart..................................................73

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the IMB-H114 motherboard. This motherboard is a high

performance, enhanced function motherboard designed to support the LGA1151

socket forIntel latest Skylake processors for high-end business or personal desktop

markets.

This motherboard is based on IntelÒ H110 Chipset for best desktop platform solu-

tion.It supports up to 16 GB of system memory with dual channel DDR4 2133 MHz.

Two PCI Express16X Gen3 slots (1 with PCIex4) and one PCIE1X Gen2 are sup-

ported, intended for Graphics Interface. In addition, one PCI slot is for extending

usage.

It integrates USB 2.0 and USB 3.0 interface, supporting up to six USB 2.0 ports (two

USB 2.0 ports at the rear panel and three USB 2.0 headers support additional four

USB 2.0 ports) and four USB 3.0 ports at rear panel).

The motherboard is equipped with advanced full set of I/O ports in the rear panel,

including PS/2 mouse and PS/2 keyboard connectors, one HDMI port, one COM

port, one VGA port, one DVI port, two USB 2.0 ports, four USB 3.0 ports, two LAN

ports, and audio jacks for line-in, line-out.

In addition, this motherboard supports four SATA 6.0Gb/s connectors for expansion.

Feature

• DirectX11.1-compliant GCN-based graphics architecture

•Supports “Hyper-Threading” technology APU

• Supports Win8 and UEFI Secure Boot.

“Hyper-Threading” technology enables the operating system into thinking

it’s hooked up to two processors, allowing two threads to be run in parallel, both

on separate “logical” processors within the same physical processor.

The motherboard uses Skylake series CPU that carries the following features:

Processor

Chipset

• Supports DDR4 2133 (1GB/ 2GB/ 4GB/ 8GB) SDRAM with two-channel

architecture

• Up to 16GB 288 pin DIMM memory module support

Memory

Audio

• 2 Channel High Definition Audio Codec

•Meets Microsoft Windows Logo Program and Lync audio

requirements

•All DACs supports 44.1k/48k/96k/192kHz sample rate

•Software selectable 2.5V/3.2V/4.0V VREFOUT

•Direct Sound 3DTM compatible

•Power Support: Digital: 3.3V; Analog: 5.0V

The integrated Skylake H110 chip is a dual-chip with proven reliability and high

performance.

• Support one PCI Express x1 slot

• Integrated four SATA 6.0 Gb/s Host Controllers

• Six USB 2.0 ports supported

• Four USB 3.0 port supported

•Support two PCI Express x16 Gen3 slots (1 with PCIex4)

• Support one PCI slot

• Intel®High Definition Audio Controller

Expansion Options

The motherboard comes with the following expansion options:

• One PCI Express x1 slot

•Four SATA 6.0Gb/s connectors

•Support two PCI Express x16 Gen3 slots (1 with PCIex4)

• Support one PCI slot

The motherboard has a full set of I/O ports and connectors:

Integrated I/O

• Two LAN ports

• One Serial port (COM)

• One DVI port (DVI-D)

• two USB 2.0 ports

• One VGA port

• One HDMI port

• Four USB 3.0 ports

• One PS/2 keyboard and PS/2 mouse connector

• Audio jacks for line-out and Mic-in

The firmware can also be used to set parameters for different processor clock

speeds.

•Power management

• Wake-up alarms

• APU parameters

•APU and memory timing

•Graphic parameters

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system

features including the following:

1. Some hardware specifications and software items are subject to change

without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated

in the ambiance between 0 and 60 ° C. (NOTICE: Test method: bare PCB

with 100% loading running Pass Mark 7.0 at chamber 60 °C)

Ethernet LAN

The onboard LAN provides the following features:

• Supports PCI ExpressTM 1.1

•IEEE 802.3/z

•Wake-on-LAN (including from S3, S4, S5, power button off)

and remote wake-up support

•PXE and RPL support

8 9

CPU

Speciﬁcaons

•Intel

H110 ChipsetChipset

•Dual-channel DDR4 memory architecture

• 2 x DDR4 DIMM sockets support up to 16 GB

•Supports DDR4 2133 MHz

Memory

• 2 x PCI Express x16 Gen3 slots (1 with PCIex4)

• 1 x PCI Express x1 Gen2 slot

• 1 x PCI slot

•Supported by Intel

H110 Express Chipset

- 4 x Serial ATA 6.0 Gb/s devices

Expansion

Slots

Storage

• 1 x PS/2 keyboard & PS/2 mouse connectors

• 1 x HDMI port

• 1 x VGA port

• 1 x DVI port (DVI-D)

• 2 x USB 2.0 ports

• 4 x USB 3.0 ports

• 2 x RJ45 LAN connectors

• 1 x COM port (RS232/422/485 Controlled by BIOS)

• 1 x Audio port (Line in, line out)

Rear Panel I/O

LAN• Intel I211AT

•Intel I219V

• Realtek ALC662 HD audio CODEC

Audio

•LGA1151 socket forIntel Skylake processors, Dual cores

• 1 x 24-pin ATX Power Supply connector

• 1 x 4-pin ATX_12V Power Supply connector

• 1 x 4-pin CPU_FAN connector

• 1 x 4-pin SYS_FAN connector

• 4 x SATA III 6.0Gb/s connectors

• 1 x Front panel switch/LED header

• 1 x Front panel audio header

• 1 x USB 2.0 header support addional two USB 2.0 ports

• 1 x 5-pin USB 2.0 header support addional one USB 2.0 port

• 1 x USB 2.0 port

• 9 x Onboard Serial port headers (COM2~10) (RS232)

• 1 x Clear CMOS header with jumper

• 1 x ME DISABLE header with jumper

• 1 x Buzzer header

• 1 x INT_SPK header

• 1 x DIO header

• 1 x J1 jumper

• 1 x J2 jumper

• 1 x J3 jumper

Internal I/O

Connectors &

Headers

• AMI BIOS with 64Mb SPI Flash ROM

• Supports Plug and Play, STR (S3) / STD (S4) , Hardware monitor

• Supports ACPI & DMI

• Audio, LAN, can be disabled in BIOS

• F7 hot key for boot up devices opon

System BIOS

Form Factor• Micro ATX Size, 244mm x 244mm

10 11

Motherboard Components

LABEL COMPONENTS

1. CPU LGA1151 socket for Intel Skylake processors

2. CPU_FAN CPUcooling fan connector

3. DIMM1~2 288-pin DDR4 Module slots

4. DIO Digital Input &output header

5. J1 Power mode Select jumper

6. COM2~10 Onboard serial port headers

7. ATX_POWER Standard 24-pin ATX power connector

8. BAT Baery

9. SATA1~4 Serial ATA 6.0Gb/s connectors

10. BZ Buzzer

11. CLR_CMOS Clear CMOS header with jumper

12. F_PANEL Front panel switch/LED header

13. ME_DISABLE Disble ME header with jumper

14. TPM Trusted PlaormModual header

15. F_USB1~3 Front panel USB 2.0 headers

16. INT_SPK Speaker header

17. F_AUDIO Front panel audio header

18. PCIE4X PCI Express x16 Gen2 slot for graphics interface

19. PCI 32-bit add-on card slot

20. PCIE1X PCI Express x1 slot

21. PCIE16X PCI Express x16 Gen3 slot for graphics interface

22. SYS_FAN Systemcooling fan connector

25. ATX_12V Auxiliary 4-pin power connector

23. J3 COM1 Transmission Distance Select jumper

(J3 and J2 need to switch at the same me)

24. J2 COM1 Transmission Distance Select jumper

(J3 and J2 need to switch at the same me)

Table of Motherboard Components

This concludes Chapter 1. The next chapter explains how to install the motherboard.

IMB-H114

12 13

Memo

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

•Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the DTX system case. Some features on the motherboard

are implemented by cabling connectors on the motherboard to indicators and switches

on the system case. Make sure that your case supports all the features required.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries a ATX form factor of 244 x 244 mm. Choose a case that

accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

14 15

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the jumper

caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When

the jumper cap is placed on both pins, the

jumper is SHORT. If you remove the jumper

cap, or place the jumper cap on just one pin,

the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins

1 and 2 are SHORT.

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is

labeled.

Jumper Settings

Jumper TypeDescription Setting (default)

CLR_CMOS3-pinClear CMOS

1-2: NORMAL

Before clearing the

CMOS, make sure to

turn off the system.

To avoid the system instability after clearing CMOS, we recommend

users to enter the main BIOS setting page to “Load Default Settings”

and then “Save and Exit Setup”.

(Default)

2-3: CLEAR

J 1 3-pin

1-2: ATX 1

(Default)

2-3: AT

Power supply

switch

IMB-H114

1716

Jumper TypeDescription Setting (default)

ME_DISABLE3-pinDisable ME

1-2: NORMAL1

(Default)

2-3: ME DISABLE

J3*3-pin

1-2: Long distance

transmission (for

RS-422, RS-485)

(Default)

2-3: Short distance

transmission

COM1

Transmission

Distance

switch

J2*3-pin

1-2: Long distance

transmission (for

RS-422, RS-485)1

(Default)1

2-3: Short distance

transmission

COM1

Transmission

Distance

switch

*J3 and J2 need to switch at the same time.

S0->S5->G3 S0->G3 S0->S5->G3 S0->G3

Power On S5->S0 S5->S0 S5->S5 S5->S5

Last State S5->S5 S5->S0 S5->S5 S5->S5

Power OﬀS5->S5 S5->S5 S5->S5 S5->S5

ATX Mode

EUP=Disabled EUP=Enabled

S0->S5->G3 S0->G3 S0->S5->G3 S0->G3

Power On S5->S0 S5->S0 S5->S0 S5->S0

Last State S5->S0 S5->S0 S5->S0 S5->S0

Power OﬀS5->S0 S5->S0 S5->S0 S5->S0

AT Mode

EUP=Disabled EUP=Enabled

Note:

Installing Hardware

Caution: When installing a CPU heatsink and cooling fan make sure that

you DO NOT scratch the motherboard or any of the surface-mount

resistors with the clip of the cooling fan. If the clip of the cooling fan

scrapes across the motherboard, you may cause serious damage to the

motherboard or its components.

On most motherboards, there are small surface-mount resistors near the

processor socket, which may be damaged if the cooling fan is carelessly

installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips.

Also, install the cooling fan in a well-lit work area so that you can clearly

see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system

bus frequency for the processor. You may be able to change the settings in the system

Setup Utility. We strongly recommend that you do not over-clock processors or

other components to run faster than their rated speed.

This motherboard has an LGA1151 socket. When choosing a processor, consider the

performance requirements of the system. Performance is based on the processor

design, the clock speed and system bus frequency of the processor, and the quantity

of internal cache memory and external cache memory.

Warning:

1. Over-clocking components can adversely affect the reliability of the

system and introduce errors into your system. Over-clocking can

permanently damage the motherboard by generating excess heat in

components that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the

power outlet before installing or removing the motherboard or other

hardware components.

Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the

following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the

PC up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

Installing the Processor

18 19

CPU Installation Procedure

The following illustration shows CPU installation components.

A. Press the hook of lever down with your thumb and pull it to the

right side to release it from retention tab.

B. Lift the tail of the load lever and rotate the load plate to fully open

position.

C. Grasp the edge of the package substrate. Make sure pin 1 indicator

is on your bottom-left side. Aim at the socket and place the package

carefully into the socket by purely vertical motion.

D. Rotate the load plate onto the package IHS (Intergraded Heat

Spreader). Engage the load lever while pressing down lightly onto the

load plate. Secure the load lever with the hook under retention tab.

Then the cover will flick automatically.

Please save and replace the cover onto the CPU socket if processor is

removed.

E. Aplly some thermal grease onto the contacted area between the heatsink

and the CPU, and make it to be a thin layer.

F. Fasten the cooling fan supporting base onto the CPU socket on the

motherboard. And make sure the CPU fan is plugged to the CPU fan

connector.

G. Connect the CPU cooler power connector to the CPU_FAN connector.

1. To achieve better airflow rates and heat dissipation, we suggest

that you use a high quality fan with 3800 rpm at least. CPU fan and

heatsink installation procedures may vary with the type of CPU fan/

heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a

CPU.

3. Return Material Authorization (RMA) requests will be accepted

only if the motherboard comes with the cap on the LGA1151 socket.

Table des matières

Autres manuels Strontech Carte mère

Strontech

Strontech Intel Haswell Series Manuel utilisateur

Strontech

Strontech ECB-H61102H Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur