STMicroelectronics SPC58XCADPT176S Manuel utilisateur
Introduction
The SPC58XCADPT176S evaluation board supports STMicroelectronics SPC584BxxE7, SPC584CxxE7 and SPC58ECxxE7
microcontrollers in LQFP 176 package.
Figure 1. SPC58XCADPT176S
Note: picture not contractual
SPC58XCADPT176S evaluation board
UM2763
User manual
UM2763 - Rev 1 - September 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1Overview
The SPC58XCADPT176S mini module is an evaluation board supporting STMicroelectronics SPC584BxxE7,
SPC584CxxE7 and SPC58ECxxE7 microcontrollers in LQFP176 package.
The mini module is designed to be connected onto the SPC58xxMB motherboard, offering a mechanism for easy
customer evaluation of the supported devices, and to facilitate hardware and software development.
The mini module may be used as a stand-alone unit allowing access to the CPU, but no access to the I/O pins as
any motherboard peripherals.
Figure 2. Overview of SPC58XCADPT176S mini module - top
UM2763
Overview
UM2763 - Rev 1 page 2/24
Figure 3. Overview of SPC58XCADPT176S mini module - bottom
1.1 Package contents
An SPC58XCADPT176S adapter package includes the following item:
• SPC58XCADPT176S mini module
1.2 Supported devices
The SPC58XCADPT176S mini module supports the following STMicroelectronics family of microcontrollers in
LQFP176 package:
• SPC584CxxE7/SPC58ECxxE7
• SPC584BxxE7
UM2763
Package contents
UM2763 - Rev 1 page 3/24
2License agreement
The packaging of this evaluation board was sealed with a seal stating, “by breaking this seal, you agree to the
terms and conditions of the evaluation board license agreement, the terms and conditions of which are available
at http://www.st.com/ebla”. Upon breaking the seal, you and STMicroelectronics entered into the evaluation board
license agreement, a copy of which is also enclosed with the evaluation board for convenience.
Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with
other products and is not suitable for any safety or other commercial or consumer application. This evaluation
board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied,
including the implied warranties of merchantability and fitness for a particular purpose.
UM2763
License agreement
UM2763 - Rev 1 page 4/24
3Handling precautions
Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.
Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure
the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.
UM2763
Handling precautions
UM2763 - Rev 1 page 5/24
4Hardware description
4.1 Hardware features
The SPC58XCADPT176S mini module board has the following features:
• Connector for external power supplies input (5 V, 3.3 V, 1.25 V) used in stand-alone mode.
• Reset button with driver and led indicator
• Socket for device in eLQFP176 package with exposed pad down
• Debug ports:
– 12-pin SAMTEC connector for SIPI interface
– 14-pin header connector for JTAG port
– 12-pin header connector for LFAST interface
• 40 MHz crystal main oscillator with jumpers to optionally disconnect it
• 8 MHz oscillator with jumpers to optionally disconnect it
• Clock input through SMA connector to optionally disconnect it
• Jumper for boot configuration
• 2 X Samtec QSH series, 240 way connector to connect mini module to motherboard
4.2 Hardware dimension
The mini module has the following dimensions:
• PCB area: 127 mm X 114.3 mm
• Top components height: 19.4 mm max
• Bottom components height: 3.5 mm max
• PCB thickness: 1.6 mm
UM2763
Hardware description
UM2763 - Rev 1 page 6/24
5Power and system configuration
5.1 Power supplies
When the mini module is plugged onto the motherboard, power is supplied directly by the motherboard. In this
setup, the external power supply input available on the mini module should NOT be used.
When the SPC58XCADPT176S mini module is used as a stand-alone board, external power supplies must be
used (5.0 V, 3.3 V, 1.25 V).
The following jumpers are used to configure the power supply:
Table 1. Power configuration jumpers
Jumper Description Default Position
J1 VDD_HV_ADR voltage configuration
from 5.0V_LR or 3.3V_SR 1-2 (5.0V_LR) Figure 4. SPC58XCADPT176S top mini
module view - C2
J2 VDD_HV_ADV voltage configuration
from 5.0V_LR or 3.3V_SR 1-2 (5.0V_LR) Figure 4. SPC58XCADPT176S top mini
module view - C2
J3 VDD_HV_JTAG voltage configuration
from 5.0V_SR or 3.3V_SR 1-2 (5.0V_SR) Figure 4. SPC58XCADPT176S top mini
module view - B2
J6 VDD_HV_IO_MAIN voltage configuration
from 5.0V_SR or 3.3V_SR 1-2 (5.0V_SR) Figure 4. SPC58XCADPT176S top mini
module view - B2
J7 VDD_HV_IO_FLEX voltage configuration
from 5.0V_SR or 3.3V_SR 1-2 (5.0V_SR) Figure 4. SPC58XCADPT176S top mini
module view - B2
J39 Supply for BALLAST circuit configuration
from VDD_HV_IO_MAIN or 5.0V_SR 1-2 (VDD_HV_IO_MAIN) Figure 4. SPC58XCADPT176S top mini
module view - A2
J40
VDD_LV voltage configuration from
BALLAST circuit, 1.25V_SR or
SMPS_REGULATOR_OUT
2-3 (1.25V_SR) Figure 4. SPC58XCADPT176S top mini
module view - A3
5.2 Microcontroller configuration
The following jumper needs to configure the board for used STMicroelectronics microcontroller SPC584Cxx/
SPC58ECxx:
Table 2. Microcontroller SPC584Cxx/SPC58ECxx configuration related jumpers
Jumper Description Default Position
J46 Device pin 153 BCTRL /
PM[15] function configuration
Close 2-3 (connect pin as
BCTRL with BALLAST circuit)
Figure 4. SPC58XCADPT176S top mini module
view - A3
UM2763
Power and system configuration
UM2763 - Rev 1 page 7/24
5.3 Port configuration
The following jumper need to configure the ports:
Table 3. Ports related jumpers
Jumper Description Default Position
J30 TESTMODE settings Close Figure 4. SPC58XCADPT176S top mini module view - B2
J13 PF[15]/EVTI connection to QSH motherboard
connectors Close Figure 4. SPC58XCADPT176S top mini module view - A2
J31 PH[11]/EVTO connection to QSH motherboard
connectors Close Figure 4. SPC58XCADPT176S top mini module view - A2
5.4 System clock configuration
The mini module supports the usage of crystal clock sources as well as external clock source:
Table 4. Clock configuration jumpers
Jumper Description Default Position
J21 40 MHz crystal clock source Enable
for pin EXTAL 1-2 (XT1 pin2) Figure 4. SPC58XCADPT176S top mini module view -
C3
J23 40 MHz crystal clock source Enable
for pin XTAL 1-2 (XT1 pin1) Figure 4. SPC58XCADPT176S top mini module view -
C3
J22 Enable 8 MHz oscillator power supply Open Figure 4. SPC58XCADPT176S top mini module view -
D3
J24 External clock source from 8 MHz
oscillator or SMA connector
1-2 (8 MHz
oscillator)
Figure 4. SPC58XCADPT176S top mini module view -
D3
5.5 Reset circuit
The mini module supports different ways to reset the microcontroller.
To use and perform the reset driving there are different jumpers and switches:
Table 5. Reset configuration jumpers
Jumper Description Default Position
SW1 Reset push button Open Figure 4. SPC58XCADPT176S top mini module view - D1
J27
Connect the external reset to the reset driver
for
ESR0 and PORST pins
Close Figure 4. SPC58XCADPT176S top mini module view - D1
J25 Connect the external reset to ESR0 pin Close Figure 4. SPC58XCADPT176S top mini module view - D2
J26 Connect the external reset to PORST pin Close Figure 4. SPC58XCADPT176S top mini module view - D2
UM2763
Port configuration
UM2763 - Rev 1 page 8/24
5.6 Test points
The mini module has several test points. Below all test point description:
Table 6. Test points
Test Point Description Position
TP3 JCOMP_RxDATA_N test point Figure 4. SPC58XCADPT176S top mini module view - A3
TP4 TCK test point Figure 4. SPC58XCADPT176S top mini module view - A2
TP5 TMS_TxDATA_P test point Figure 4. SPC58XCADPT176S top mini module view - A3
TP6 TDI_TxDATA_N test point Figure 4. SPC58XCADPT176S top mini module view - A3
TP7 TDO_RxDATA_P test point Figure 4. SPC58XCADPT176S top mini module view - A3
TP9 SIPI_RXN test point Figure 4. SPC58XCADPT176S top mini module view - C2
TP11 SIPI_TXN test point Figure 4. SPC58XCADPT176S top mini module view - C2
TP13 SIPI_RXP test point Figure 4. SPC58XCADPT176S top mini module view - C2
TP15 SIPI_TXP test point Figure 4. SPC58XCADPT176S top mini module view - C2
TP24 J16A, QSH connector, pin19 (PA14) test point Figure 4. SPC58XCADPT176S top mini module view - A4
TP22 J16A, QSH connector, pin10 (PA5) test point Figure 4. SPC58XCADPT176S top mini module view - A4
TP28 J16A, QSH connector, pin11 (PA6) test point Figure 4. SPC58XCADPT176S top mini module view - A4
TP25 J16A, QSH connector, pin12 (PA7) test point Figure 4. SPC58XCADPT176S top mini module view - B4
TP26 J16A, QSH connector, pin13 (PA8) test point Figure 4. SPC58XCADPT176S top mini module view - A4
TP23 J16A, QSH connector, pin14 (PA9) test point Figure 4. SPC58XCADPT176S top mini module view - B4
5.7 Connectors
The mini module has other connectors described in the below table.
Table 7. Other connectors
Connectors Description Position
J20 12-pin header connector for SIPI interface Figure 4. SPC58XCADPT176S top mini module view - C2
J18 14-pin header connector for JTAG port Figure 4. SPC58XCADPT176S top mini module view - A4
CN1 12-pin SAMTEC connector for JTAG/LFAST
LVDS interface Figure 4. SPC58XCADPT176S top mini module view - A3
J36, J37 DC-DC Regulator Module Figure 4. SPC58XCADPT176S top mini module view - A1/A2
J16, J17 2 X Samtec QSH series, 240 way connector to
connect mini module to motherboard Figure 5. SPC58XCADPT176S bottom mini module view
UM2763
Test points
UM2763 - Rev 1 page 9/24
5.8 Debug configuration jumpers
The mini module has 2 jumpers that can be used for the debug configuration/standard configuration mode
described in the following table:
Table 8. Debug configuration jumpers
Connectors Description Position
J41
EVTO/ESR0 configuration jumper:
• Configuration 1-2 allowed
• Configuration 2-3 reserved
Figure 4. SPC58XCADPT176S top mini module view - A3
J42
PORST/ESR0 configuration jumper:
• Configuration 1-2 allowed
• Configuration 2-3 reserved
Figure 4. SPC58XCADPT176S top mini module view - A3
UM2763
Debug configuration jumpers
UM2763 - Rev 1 page 10/24
Table des matières
Autres manuels STMicroelectronics Carte mère
STMicroelectronics
STMicroelectronics STM32100B-EVAL Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-IME008V1 Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-IHT008V1 Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-ILL028V1 Manuel utilisateur
STMicroelectronics
STMicroelectronics ST7MDTULS-EVAL Manuel utilisateur
STMicroelectronics
STMicroelectronics UM1036 Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-LLL002V1 Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-IHT005V2 Manuel utilisateur
STMicroelectronics
STMicroelectronics AEK-POW-BMS63EN Manuel utilisateur
STMicroelectronics
STMicroelectronics SPC58NHADPT302S Manuel utilisateur
STMicroelectronics
STMicroelectronics SPC570SADPT64S rev. B Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-ILL029V1 Manuel utilisateur
STMicroelectronics
STMicroelectronics STM32L476 Manuel utilisateur
STMicroelectronics
STMicroelectronics STR9 Series Manuel utilisateur
STMicroelectronics
STMicroelectronics STM32G081B-EVAL Manuel utilisateur
STMicroelectronics
STMicroelectronics EVALSTGAP4S Manuel utilisateur
STMicroelectronics
STMicroelectronics STEVAL-MKI109V2 Manuel utilisateur
STMicroelectronics
STMicroelectronics STM32F4 Series Manuel utilisateur
STMicroelectronics
STMicroelectronics L62 Series Manuel utilisateur
STMicroelectronics
STMicroelectronics LED7707 Instructions d'installation et d'utilisation
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
