StepperOnline DM480AI Manuel utilisateur

User Manual

DM480AI

2-phase Speed Control Stepper Driver

Address:15-4, #799 Hushan Road, Jiangning, Nanjing, China

Tel: 0086-2587156578

Web: www.omc-stepperonline.com

Sales:[email protected]

Support: [email protected]

Stepper drive with speed control DM480AI easy manual

2-phase Speed Control Stepper Drive

20-40VDC, 1.0-8.4A peak current, 2-axis motor control,0-10V analog input

Peak

RMS

SW1

SW2

SW3

1.0A

0.7A

1.4A

1.0A

off

2.1A

1.5A

off

2.8A

2.0A

off

4.2A

3.0A

off

5.6A

4.0A

off

7.0A

5.0A

off

8.4A

6.0A

off

Motor Speed (RPM)

SW4

SW5

SW6

0-100

0-150

off

0-200

off

0-250

off

0-300

off

0-350

off

0-400

off

0-450

off

Motor Connector

Power & Motor Connector

Control Signals Connector

PIN #

Name

Description

PIN #

Name

Description

VDC

Connect to positive terminal of power

supply

GND

GND of analog input

GND

Connect to GND of power supply

AIN

0 -10V of analog input

B-

Motor 1

+10V

Output 10V @ 20mA

B+

ENA-

Motor Start / Stop input

A-

DIR-

Motor direction

A+

OPTO

Common +24V for start/stop and direction signals

B-

Motor 2

B+

A-

A+

DIP Switch Setting

Preparation

24VDC or 36VDC power supply

Command source: Simple switch signal, or I/O signal

of PLC, or 0-10V analog input

24V logical voltage for motor start/stop and motor

direction.

One or two stepper motor

DM480AI Size (unit: mm)

Power Supply Connection

Rang 20-40VDC, recommend 24-36VDC power

supply, higher power voltage brings better

performance at high speed.

Pay attention to polarity of power, otherwise, the drive

will burn out.

118

112

22.5

4.5

4-Ф3.5

75.5

25.3

47.8

Stepper drive with speed control DM480AI easy manual

0 - 10V Analog Control Connection

DM480AI has three wiring methods, Figure 1 is directly connected to the analog output of the controller, Figure 2 is external

potentiometer speed regulation. Figure 3 indicates that if only a fixed speed is required and the drive dials exactly this speed, the AIN can

be directly shorted to +10V without a potentiometer.

Note:

(1) This driver OPTO can only be connected to 24V, ENA is as start/stop signal, and DIR is as motor rotation direction.

(2) The motor is locked at power on.

(3) If use a potentiometer, the resistance value is recommended to be more than 1KΩ.

(4) Please pay attention to the DIP switch settings and motor wiring before power on.

Autres manuels StepperOnline Unité de contrôle

StepperOnline

StepperOnline DM456AI Manuel utilisateur

StepperOnline

StepperOnline CL57T Manuel utilisateur

StepperOnline

StepperOnline DM542S Manuel utilisateur

StepperOnline

StepperOnline ISD02 Manuel utilisateur

StepperOnline

StepperOnline DM542T Manuel utilisateur

StepperOnline

StepperOnline Y Series Mode d’emploi

StepperOnline

StepperOnline MA860H Manuel utilisateur

StepperOnline

StepperOnline CL86T Manuel utilisateur

StepperOnline

StepperOnline CL86T Manuel utilisateur

StepperOnline

StepperOnline DM542T Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur