Status Pro T250 Manuel utilisateur

T250

Laser transmitter

Instruction manual

Another fine solution by

T250

Status Pro – T250 Instruction manual

CONTENTS

Instruction manual – English

Laser transmitter T250

(SP T250-P)

We woul like to congratulate you on the purchase of your Status Pro R310 Laser receiver.

Before initial usage you shoul carefully rea the safety instructions as well as the user

gui elines containe in this manual. We wish you every success when using this

Measurement Instrument.

Please note: User Manuals can be amen e when improvements or changes to the prouct

range have been carrie out. Use the link below to make sure you have the most up to

ate version of your User Manual. www.statuspro.co / achine_geo etry/docu ents/

Contents

1. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Class of laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Stan ar s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Instrument care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.6 Liability Exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 Aligning the laser beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.2 Setting up the T250 for straightness measurements . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4. TECHNICAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

6. PRODUCTS AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Status Pro – T250 Instruction manual 3

SAFETY INSTRUCTIONS

1. Safety Instructions

1.1 Class f Laser

The laser light emitte from a Status Pro Laser has an Output Rating of < 1,0 mW.

The Laser is place in the category „Class 2“ an is classifie as safe for the use as a

Measurement instrument. There are however a few safety aspects to be observe :

Cauti n!

•Do not stare into the laser beam.

•Do not point the laser beam at other people.

•Observe the local safety gui elines on Site an if in oubt consult

the Site safety Engineer.

•Do not use the equipmentin amp or moist locations.

•Ensure sha ing of the equipment against irect sunlight or heat

sources.

•Flui s or rain as well as extreme temperature con itions may

amage the equipment.

N te

Do not violently shake the Laser or other sensors an always

protect against falls. This can amage the structure or the optics

of the instrument resulting in false measurements.

Do not touch rotating parts when in use!

T250

Status Pro – T250 Instruction manual

SAFETY INSTRUCTIONS

1.2 Standards

All Status Pro Laser an Receiver Instruments are evelope an manufacture

accor ing to the following CE Stan ar s:

•EN 55 011

•EN 55 022

•EN 61 000-4-2

•EN 61 000-4-3

•EN 60 335

1.3 Instrument care

Your measurement instrument is esigne for use in an in ustrial environmentan can

withstan water splashes or light spray as well as ust. Clean the equipment using a soft

cotton cloth an a mil soap solution. Laser apertures as well as well as sensor areas

shoul only be cleane using a soft, ry an ust-free cloth. Do not use paper towels to

clean glass surfaces as they coul scratch. Avoi contact with grease, oil or oil-base

solutions when han ling the equipment..

1.4 Maintenance

The mechanical components of your equipment are prone to natural wear an tear! If the

Instrument appears to have a technical efect, contact the Manufacturer. Das Gerät nicht

eigenstän ig öffnen. Attempte repairs through unauthorise personnel makes the gua-

rantee null an voi !

Always store the equipment un er ry con itions an use the case for transportation.

N te

To be able to i entify the equipment when seeking a vice always

quote the serial number of the equipment. The Manufacturer oes

not accept any responsibility for amage incurre through incorrect

maintenance carrie out by non-authorise personnel.

Status Pro – T250 Instruction manual 5

SAFETY INSTRUCTIONS

1.5 Calibrati n

To guarantee measurement accuracy, an reliable operation of your

Status Pro Measure ment System, it is of utmost importance that the

recommen e Service Intervals be a here to. The System shoul be

checke for serviceability, an recalibrate by the Status Pro workshops

every 12 months.

Within the scope of the service checks, the complete system will also be examine for

possible wear or amage, as well as receiving any software up ates. The ate of the next

service check for your equipment is stampe on the Status Pro calibration sticker.

To ensure trouble-free processing of the service an calibration checks, simply use

the form you will fin using the following link:

www.statuspro.co / achine_geo etry/service_support/calibration_repair/

1.6 Liability Exclusi n

The Status Pro GmbH oes not accept responsibility for amage incurre through incor-

rect use or han ling of the equipment. To ensure correct usage, a foun e knowle ge of

the equipment is essential. It is of the utmost importance that you rea an un erstan the

Han book!

No responsibility will be accepte for amage incurre through ignorance or isregar ing

of the operating instructions.

T250

Status Pro – T250 Instruction manual

GETTING STARTED

2. Getting starte

The T250 Laser transmitter package (SP T250-P) comprises of the T250 Laser transmitter

(I - BG 830750), a mains power supply cable (III - BG800025), an an A apter (II - 832050)

enabling mounting of the T250 Laser when using a tripo , or when using the Borealign Kit

(SP BOREALIGN).

2.1 P wer supply

To operate the T250, connect the power

supply cable to the mains, an to the

socket on the T250 housing.

Ensure that the re markings on the plug

an the socket are correctly aligne .

This ensures correct polarity.

II: A apter

III: Power

supply cableI: Laser

transmitter T250

Status Pro – T250 Instruction manual 7

GETTING STARTED

2.2 Assembly

To use the T250 with a tripo , fasten the A apter (II) to the holes on the lower face of the

housing (V) using four of the screws elivere (IV). When elivere , the T250 will have

four screws on the front an the back facing.

The cylin rical face of the a apter has a 5/8“ threa for use with a tripo fitting.

To enable mounting on a vertical surface or for use with the Borealign kit, the A apter (II)

can be fitte to the front or the rear facing, again using the supplie screws. The 5/8”

threa is continuous, so the laser beam has sight through the A apter (II).

IV IV

T250

Status Pro – T250 Instruction manual

OPERATION

3. Operation

3.1 Aligning the laser

beam

There are four a justing screw assemblies

in the housing of the T250 enabling align -

ment of the laser beam. Each of these

assemblies comprises of a fine a justment

screw (1), a coarse a justment screw (2),

an a locking nut for the coarse a justment

screw (3).

To roughly a just the laser beam, loosen

the locking nut, align the laser beam with

the coarse screw (2) an the tighten up the

locking nut again. Fine a justment is

carrie out with locking nut tightene up.

When the T250 is in the horizontal position

(see below) the two screws on the upper

si e (Y1 & Y2) are use to align the laser

beam vertically.

The two screws on the si e (X1 & X2)

are use for the horizontal align ment of

the laser beam.

Y 1

X 1

X 2

Y 2

∆Y

∆X

Status Pro – T250 Instruction manual 9

OPERATION

Simply explaine , the laser beam of the T250 is house in a tube. Four screws are

attache to this tube, two on the si e an two on top. This arrangement enables alignment

of the laser angle as well as the parallel shift in both the vertical an the horizontal plane.

Example:

1) If the Y1 screw is move ownwar s

(screwe in) then the angle of the laser

beam will also slope ownwar s

2) If both Y1 an Y2 are move ownwar s

(screwe in) then the laser laser beam will

move parallelly ownwar s = parallel shift

The a justments in the horizontal plane

(X1 & X2) are carrie out in exactly the

same way.

X 1 X 2

Y 1

Y 1 Y 2

Y 2

T250

Status Pro – T250 Instruction manual

OPERATION

3.2 Setting up the T250 f r straightness

measurements

A common task woul be to measure a Linear Gui e for straightness in the X an Y axes. To

be able to carry out this measurement, the laser beam has to be aligne , to make sure that

the laser beam hits the etector over the complete length of the gui e.

Aligning the T250 to carry out the measurement of a Linear gui e:

1) Mount the T250 on a tripo or irectly on the machine to be measure .

2) Connect the T250 to an appropriate power supply.

3) Position the sensor on the gui e as close as possible to the T250.

4) Carry out a rough a justment of the T250 Laser itself so the laser beam meets the centre

of the etector.

5) Move the etector as far away as possible from the T250 Laser.

6) A just the angle of the laser beam using the (X1 / Y1) screws until

the laser beam hits the centre of the sensor again.

7) Move the sensor as close to the laser as possible.

Table des matières

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur