8
www.spokey.eu
www.spokey.pl
ASSEMBLY INSTRUCTIONS (Drawings –p. 26-28)
ATTENTION! Don’t connect the device to the power source until you finish
the assembly.
Remember that the treadmill should be always transported, lifted and
mounted by 2 people. Provide assistance for the device assembly.
STEP 1 Remove the treadmill from the box and place it on a level, flat
surface.
Lift the console with the side columns (3,4) and align them, so that the
screw holes correspond to each other.
STEP 2 One person should hold the side columns, another one –screw
the bolts.
Use two oval head bolts M8x50 (10) and two nylon nuts M8 (11) to fix the
left and rightside columns (3, 4)to themain frame (1). Use theAllen wrench
and the wrench supplied to screw them. Screw the side columns (3, 4) to
the base (1) with bolts M8x15 (14) using the Allen wrench.
Attention! At this stage do not tighten the bolts yet. Do it after step 4.
STEP 3 One person holds the console (61), while another one connects
the wires. The wire coming from the counter (54) should be connected to
the main control wire (6) coming from the right column (4).
STEP 4 After connecting the wire, slide the console (61) onto the side
columns (3, 4). Screw the console grips into the side columns with curved
washers M8 (67) and bolts M8x55 (60).
IMPORTANT! While placing the console grips (61) on the side columns (3,
4), make sure that the wires have been correctly connected and placed in
the right column (4). Be careful not to cut the wires.
Now you can tighten the bolts mounted in step 2.
STEP 5 Mount the plastic covers (56) on the console grips (61). Push the
safety key (59) into the slot in the console.
STEP 6 Check if the running belt is correctly centered. Before the first use
tighten the right and left adjustment screw by ¼ turn. Use the Allen wrench
6mm.
FOLDING AND TRANSPORT OF THE TREADMILL
Don't try to move the treadmill if it's not folded and locked. Make sure that
the plug is disconnected from power supply.
To fold the treadmill, the running area must be raised with both hands until
a gentle signal is heard, informing that the treadmill has been correctly
locked in vertical position.
To assemble the treadmill, the coloured element on the piston situated
under the treadmill belt should be pressed with one foot, which will release
the lock. Next, the treadmill belt should be gently pulled down and the
operator should back 2 metres away from the treadmill as it will unfold
automatically. Please refer to the drawing 1 (p. 24).
ATTENTION: Folded treadmill cannot be operated and utilized. Stop the
treadmill belt before folding the equipment. Folded treadmill should be
disconnected from power supply. Don't start the treadmill when it's folded.
To move the treadmill, raise it gently onto the rear transport rolls and move
it to the desired location, holding on both sides.
ATTENTION: Before transporting the treadmill make sure that it is
disconnected from power supply. The device should always be transported
by two persons..
TURNING ON THE TREADMILL
Turn the device on with the button at the front of the treadmill (ON position).
Before training, make sure that the safety key has been correctly inserted,
and the key clip is fastened to the user’s clothes.
Note: while turning on the treadmill, always stand on the immovable side
elements of the base frame. Before you climb onto it, let the treadmill reach
the speed of 0.8 km/h.
MAINTANCE
Caution: before cleaning/ lubrication you must take out the power plug from
a socket.
For cleaning the exercise machine, do not use any abrasive detergents.
Use a soft, damp cloth to remove dirt and dust.
The monitor (power supply dome) should be cleaned only with a dry cloth.
The equipment should bestored in dry places in order to protect it from any
moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part ofthe belt with a brush
and soap water once a month.
NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the black cover of the engine in
order to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
Track inclination angle setting
In this model there is a possibility of setting the inclination angle of the
running belt manually.
To choose a desired angle (there are 3 inclinations to choose), place one
hand on the back of the main frame and lift it. Pull out the lock from the
inclination angle controller with the other hand. Choose a proper inclination
angle and place the lock in the controller. It may thenbe blocked in acorrect
position.
ATTENTION! Make sure that both controllers have the same angle. Using
the treadmill with the controllers set at different angles may make the
treadmill lose its stability, which may cause the user’s injuries.
Counter manual
Belt tension adjustment
Belt Tension Adjustment-It is very important for joggers and runners in
order to provide a smooth, steady running surface. Adjustment must be
made from the right and left rear roller in order to adjust tension with the
Hexagonal Wrench provided in the parts package. The adjustment bolt is
located at the end of the rails as noted in diagram below.
Note: Adjustment is thru the small holes on the end caps.
Tighten the rear roller only enough to prevent slippage at the front roller.
Turn both the right and left bolt clockwise reasonably and inspect for proper
tension. When an adjustment is made to the belt tension, you must also
make a tracking adjustment to compensate for the change in belt tension.
DO NOT OVERTIGHTEN - Over tightening will cause belt damage and
premature bearing failure.
Belt tracking adjustment (picture, p. 29)
This treadmill is designed to keep the belt reasonably centred while in use.
It is normal for some belts to drift near one side while the belt is running
with no one on it. After a few minutes of use, the belt should have a
tendency to centre itself. If during use, the belt continues to move toward
one side, adjustments are necessary. The procedures are as below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side.
If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tightenthe left bolt and loosen the right bolt by using 6mm Hexagonal
Wrench, until the belt is centered. When adjusting the belt using the 6 mm
Hexagonal Wrenches, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
