Sony SU-XFQ005 Manuel utilisateur

Thank you for purchasing this product.

For customers

This product should be installed only by qualified Sony service representatives,

as it requires at least two people, special care, safety, and technique.

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may

result in serious injury or fire.

This instruction manual shows the correct handling of the product and important

precautions necessary to prevent accidents. Be sure to read this manual thoroughly

and use the product correctly. Keep this manual available for future reference.

For Sony dealers

Installation of a Display Unit requires two or more people, special care, and

technique. When installing a Display Unit, refer to this manual carefully. Sony is

not liable for any accidents or damages caused by incorrect installation or

handling. Please instruct the customer to retain this manual for future use.

We recommend installing the Floor Stand a short distance away from the wall.

2(US)

On Safety

Sony products are designed with safety in mind.

If the products are used incorrectly, however, it may

result in a serious situation like fire, electric shock, the

product toppling over, or the product dropping. Be

sure to observe the precautions for safety to prevent

such accidents.

For Customers

WARNING

If the following precautions are not observed,

serious injury or death through fire, electric

shock, the product toppling over, or the product

dropping can result.

This product should only be installed

by qualified Sony service

representatives.

Installation by other, non-qualified persons may result

in serious injury, as the Display Unit and the stand are

very heavy.

Do not lean on or hang from the

stand.

The stand may topple over and

cause injury.

Be sure to take measures to prevent

the Display Unit from toppling over.

If you fail to do so, the Display Unit may topple over

and cause injury. Anchor the Display Unit to a wall,

pillar, etc., to prevent it from toppling over.

Be sure to install the stand on a solid

and level floor.

Do not install the Floor Stand so that it leans in one

direction. If you do so, the Floor Stand may topple over

or the Display Unit may fall. This may cause injury.

If you install the stand on a soft surface such as a mat

or a carpet, lay a board over the designated location

beforehand.

Do not use a cracked stand.

Do not use the Floor Stand if

any cracks appear in it. The

glass may break and cause

injury.

Do not lean on or hang from the

Display Unit when it is attached to

the Floor Stand.

The Floor Stand may topple

over, or the Display Unit may

fall and cause serious injury or

death.

Do not climb on the stand or allow

children between the shelf and the

stand.

If children climb on the stand or

allow children between the

shelf and the stand, serious

injury or death through the

glass breaking, the stand

toppling over, or the Display

Unit dropping can result.

Do not cover the ventilation holes of

the Display Unit.

If you cover the ventilation

holes (with a cloth, etc.), heat

build up inside may cause fire.

Do not move the stand with the

Display Unit attached or with

connected equipment inside.

If you move the stand with the

Display Unit attached, it may

hurt your back, or the stand

may topple over and cause

serious injury. Also, any

connected equipment within

may drop causing the glass to

break or other property

damage.

Cracked Stand

3(US)

Notes on handling the stand

Forcible handling of the stand

may result in serious injury.

Remove the Display Unit and

the connected equipment before

handling the stand, and follow

the notes below.

•Be sure to have at least two people handle the stand.

•Do not grab the glass part.

•Be careful not to pinch your hands or feet.

Do not allow the AC power cord or

the display interface cable to be

pinched.

Do not allow the AC power

cord or the display interface

cable to be pinched when you

attach the Display Unit to the

Floor Stand. If the AC power

cord or the display interface

cable is damaged, this may

result in fire or electric shock.

Do not step on the stand.

You may fall, or break the glass

and cause injury.

Do not stumble over the AC power

cord or the display interface cable.

You may trip, or may cause the

stand to topple over and cause

injury. Bundle the cables

according to the Operating

Instructions to avoid stumbling

on the cables.

Do not disassemble or modify the

stand.

Do not pull out the screw that secures the glass shelf,

or remove the glass. The connected equipment may

drop, or the glass may break and cause injury or

property damage.

CAUTION

If the following precautions are not observed,

injury or property damage may occur.

Do not install any equipment other

than the specified product.

This stand is designed for the use with the specified

product only. If you install equipment other than

specified, it may fall or break, and cause injury.

Be sure to secure the Display Unit.

Secure the Display Unit to the Floor Stand using the

supplied screws. If the Display Unit is not installed

securely, it may fall, or the stand may topple over, and

cause injury.

Do not apply weight to the glass or

subject it to any kind of impact.

Do not apply pressure to the glass when installing the

Display Unit. Do not hit the glass with hard objects,

such as a screwdriver, etc. The glass may break and

cause injury.

Do not subject the glass to excessive

shock.

This stand is made of tempered

glass, but care should be taken.

If the glass breaks, glass

fragments could cause injury, so

observe the precautions below.

•Do not hit the glass or drop

any objects that may break

the glass. Avoid excessive

shock.

•Do not scratch or poke the

glass with sharp-pointed

objects.

•Do not let hard objects such

as a vacuum cleaner hit the

edges of the glass.

Notes on installation

Install the stand on a solid and level floor. Be sure the

stand is placed where it will not be deformed or

inclined. To avoid this, observe the following

precautions.

•Do not install the stand in a place subject to direct

sunlight or near a heater.

•Do not install the stand in a hot or humid place, or

outdoors.

4(US)

Note on use

Cleaning

To keep the stand clean, occasionally wipe the stand

with a dry soft cloth. Stubborn stains may be removed

with a cloth slightly dampened with diluted detergent.

Then wipe the area with a dry soft cloth. Do not use

chemicals, such as thinner or benzine, as they damage

the finish of the stand.

For Sony dealers

Be sure to thoroughly read the

safety precautions described on the

previous pages and pay special

attention to safety during the

installation, maintenance, checking,

and repair of this product.

Be sure that two or more persons do

the installation work.

Be sure that two or more persons install the Display

Unit on the Floor Stand. If necessary, include another

person to support the rear of the Display Unit. Do not

attempt to install the stand by yourself. If you do so, it

may lead to an accident or injury. Be sure to keep

children away during the installation.

Be careful not to injure your hands or

fingers during installation.

Be careful not to injure your hands or fingers when

attaching the Display Unit to the Floor Stand.

Be sure to install the Display Unit

securely by following the

instructions.

Tighten the screws securely. If the Display Unit is not

installed securely, it may fall and cause injury.

Check the parts

Name Quantity

Floor Stand

Display securing screw

M5×L16

Anchor attachment

Cable cover

Cable cover securing screw

M4×L12

Be sure to have appropriate sized Phillips screwdrivers

on hand for the various sized screws used for

assembly.

5(US)

Install the Display Unit

WARNING

A short circuit or an electric shock may result if the

AC power cord is pinched under the footing of the

stand or between other equipment.

If you stumble over the AC power cord or the

display interface cable, the stand may topple over

and cause injury.

Decide on the installation location and lay the

stand down before installing the Display Unit.

Since the Display Unit is heavy, it is recommended

that you decide on the installation location first,

and then lay the Floor Stand down before installing

the Display Unit.

Note

Do not drag the Floor Stand while it is on the floor. The

rubber footings on the base of the Floor Stand may come

off.

1Attach the Display Unit to the

Floor Stand.

Use the screw alignment holes on the rear of the

Display Unit as guides. Gently lower the Display

Unit to align the holes of the screws over the

joints of the Floor Stand.

zHint

There are finger slots located at the bottom of the

Display Unit on both sides for holding. When

attaching the Display Unit to the stand, use the slot to

support the bottom and hold the top with your other

hand.

The caution label is on the front

side of the Floor Stand.

Rear of Display Unit

Bottom of Display Unit

Joint

Holes for the display

securing screws

This Display Unit has

finger slots on both sides

at the bottom for holding.

Guides

6(US)

2Secure the Display Unit to the

Floor Stand with the four

display securing screws.

Note

When using an electric screwdriver, set the torque

setting to about 1.5 N·m.

Rear of Display Unit

Display securing

screw

M5×L16

Bundle the cables

1Connect the AC power cord and

the display interface cable to the

Display Unit.

zHint

See the Operating Instructions supplied with the

Display Unit for details on connecting the AC power

cord and the display interface cable.

Display

interface cable

AC power cord

7(US)

2Bundle the AC power cord and

the display interface cable.

1Do not forcefully pull on the cables. Leave

some slack at the connected end as you

thread the cables through the center hole on

the stand. (Stand has two holes to thread the

cables on the left and right sides.)

2Thread the cables through either the left or

right side hole of the stand.

Note

Do not forcefully pull the cable through the hole as

the metallic part of the connector may scratch the

floor. To avoid any damages to your floor, cover the

floor with a piece of thin cardboard or a cloth during

the installation.

Slacken the cables.

Cardboard or cloth

Thread the black and white

display cables together

through the hole.

3Attach the cable cover.

1Push any excess of cable inside the cable

compartment, and slide the cable cover down

until the four tabs of the cable cover snap into

place.

2Affix the cable cover with the two screws for

the cable cover.

Cable cover

Cable cover securing screw

M4×L12

8(US)

4Use the cable clamps to hold the

cables in place. Unsnap the

clamps and thread the AC power

cord and display interface cable

as shown.

Cable clamp

Cable

Pinch the cable clamps and push against

the inserted cables to snap in.

Safety measures to

prevent toppling over

WARNING

Be sure to take measures to prevent the Display

Unit from toppling over.

If you fail to do so, the Display Unit may topple

over and cause injury. Anchor the Display Unit to a

wall, pillar, etc., to prevent it from toppling over.

Prepare a commercially available strong rope or chain

and wall anchor bracket beforehand.

1Attach the two anchor

attachments to the upper free

screw holes on the rear of the

Display Unit.

2Secure the wall anchor bracket

to a solid wall or pillar.

Anchor

attachment

Table des matières

Langues :

Autres manuels Sony Support et étagère

Sony

Sony PEG-NX80V - Clie Handheld Manuel utilisateur

Sony

Sony RHT-G2000 - Home Theater Built-in Sound Rack... Manuel utilisateur

Sony

Sony SU-52NX1 Manuel utilisateur

Sony

Sony SU-WL400 Manuel utilisateur

Sony

Sony SU-560 Manuel utilisateur

Sony

Sony SU-WL450 Manuel de service

Sony

Sony SU-46NX1 Manuel utilisateur

Sony

Sony DMBK-R3012 Manuel utilisateur

Sony

Sony SU-PT2M Manuel utilisateur

Sony

Sony SU-P42T1 Manuel utilisateur

Sony

Sony SU-PT3M Manuel utilisateur

Sony

Sony SU-46WT11 Instruction Flyer Manuel utilisateur

Sony

Sony Walkman BCR-NWA800 Manuel utilisateur

Sony

Sony SU-40NX1 Manuel utilisateur

Sony

Sony KDL-46EX600 - 46" Bravia Ex Series Hdtv Mode d’emploi

Sony

Sony SU-RG13M Manuel utilisateur

Sony

Sony SU-RG12L - Stand For Rear Projection TV Manuel utilisateur

Sony

Sony Operating Instructions SU-EF41 Manuel utilisateur

Sony

Sony SU-RG11MA Manuel utilisateur

Sony

Sony SU-P50T2 Manuel utilisateur

Sony

Sony WB-PW1 Manuel utilisateur

Sony

Sony MB-806A Manuel utilisateur

Sony

Sony PSS-650P Manuel utilisateur

Sony

Sony WS-DAVLFS Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur