Sony VPL-PX11 Manuel utilisateur

.............. .........

PROTOCOL MANUAL

.............. .........

MODEL DEST. MODEL DEST.

LCD DATA PROJECTOR

VERSION 1.0

VPL-PX11 WORLD

VPL-PX11 CHINA

VPL-PX11 LCD Data Projector

VPLL-CT10/CW10 Projection Lens (Not Included)

RM-PJM12 Remote Commander

Serial No. 6,500,001 and later

Serial No. 6,000,001 to 6,500,000

VPLL-CT10 WORLD

VPLL-CW10 WORLD

RM-PJM12 WORLD

VPL-PX11

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

VPL-PX11

Table of Contents

1. Introduction ............................................................................................... 1

2. RS-232C

2-1. Communication Specifications ...................................................................... 1

2-2. Command Block Format ................................................................................ 2

2-3. Block Format.................................................................................................. 3

2-4. Connection ..................................................................................................... 4

2-5. Communication Procedure............................................................................. 4

2-5-1. Outline of Communication............................................................ 4

2-6. Communication Rules .................................................................................... 5

2-7. Approximate Return Waiting Times .............................................................. 5

3. Appendix .................................................................................................... 6

VPL-PX11

1. Introduction

This protocol manual describes the basic configuration and basic operations of various commands used

for projector. Projector can be controlled using the commands in the List of Commands provided in

Section 3 “Appendix”. Using an external CONTROLLER , etc., inputs can be switched and the power

can also be turned on and off. In the following paragraphs, “CONTROLLER” means an external device

such as a PC which controls projector using these commands.

2. RS-232C

2-1. Communication Specifications

<RS-232C Communication Signal>

.Full duplex communication channels (Flow control not performed.)

.Start-stop synchronism system

.Baud rate: 38.4 kbps (bits per second)

.The bit configuration is defined as follows.

1 START Bit +8 DATA Bits +1 PARITY Bit +1 STOP Bit

EVEN Parity.....Total number of “1”s from D0 to D7 is an even number.

D4 D5 D6 D7

(MSB)(LSB) (EVEN) BIT

PARITY STOP

BIT

START D3D2D1D0

2VPL-PX11

2-2. Command Block Format

The code from B0 to B7 as described below are transmitted.

B0 START CORD

Common in the all FORMAT

B6 CHECK SUM

B1 to B5 are calculated by OR;

0 xA9 1010 1001 0 xA9 1010 1001

0 xA9 1010 1001 0 x9A 1001 1010

Answer 1010 1001 Answer 1011 1011

0 xA9 0 xBB

B7 END CODE

Common in the all FORMAT

START CODE : 0 xA9

DATA

ITEM NUMBER ACK / NAK ITEM NUMBER

SET / GET ACK

DUMMY DATA

CHECK SUM

END CODE : 0 x9A

DATA

Transmission from

the Master side Transmission from

the Master side Reception in the Master side

(With Data)

VPL-PX11

2-3. Block Format

START CODE

DATA

ITEM NUMBER

SET / GET

CHECK SUM

END CODE

START CODEB0

DUMMY DATA

ACK / NAK

ACK

CHECK SUM

END CODE

START CODEB0

DATA

ITEM NUMBER

CHECK SUM

END CODE

Transmission from the Master side

Reception in the Master side

Reception in the Master side (With Data)

Data transmission to the Projector

Start of Command

Set the Data Category Value desired.

Refer to the Table 1 for details.

SET: 0 x 00 (Set data)

GET: 0 x 01 (Get data)

SET: Data to be set (Refer to the Table 2)

GET: Unused. Set Dummy data [0 x 00, 0 x 00]

Check Sum

End of Command

Receive results of the data transmission from the Projector.

Start of Command

Results correspond with the data transmission

Refer to the Table 3 for the data in detail.

[0 x 03]

Express Reply data either of ACK, or NAK

This data does not mean any senses.

Dummy Data [0 x 00, 0 x 00] is stored.

Check Sum

End of Command

Check Sum

End of Command

Receive data from the Projector

Start of Command

Received data

Refer to the Table 1 in detail.

[0 x 02]

Express data to be Reply data

Received data

Refer to the Table 2 in detail.

4VPL-PX11

2-4. Connection

<RS-232C Connection>

Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable.

The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.

Pins indicated as D-Sub 25 Pin are not used.

Assured cable length: 15 m (However, assurance may not be applicable for some cables.)

The software for controlling the projector from a PC is intended for performing transmission and recep-

tion for only the TxD and RxD lines.

Therefore there is no handshake normally performed by RS-232C.

2-5. Communication Procedure

2-5-1. Outline of Communication

All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the

command block format. Communication is started by the issue of a command at CONTROLLER and

ended when the return data is sent to CONTROLLER after DEVICE receives the command.

CONTROLLER is prohibited from sending several commands at one time. This means that after CON-

TROLLER sends one command, it cannot send other commands until DEVICE returns the return data.

DEVICE sends the return data after processing the command. The time from when CONTROLLER sends

the command until the return data is returned differs according to the contents of the command.

In some cases, CONTROLLER may receive data from DEVICE even though it has not sent a command.

(For example, during SYS setting, SIRCS command, and switcher information when switcher is selected.)

Note: When Sircs Direct Command is sent, return data may not be returned in some cases.

D-Sub 9 Pin

Shell = FG

D-Sub 25 Pin

Name

TxD

RxD

RTS

CTS

DSR

DCD

DTR

Grounding for safety protection or cable shield

Transmission data

Reception data

Transmission request

Transmission permission

Data set ready

GND for signal

Data channel signal carrier detection

Data terminal ready

Calling display (Presence/absence of calling signal)

VPL-PX11

2-6. Communication Rules

.When sending a command from CONTROLLER, the return data from PROJECTOR should be re-

ceived first before sending the next command. Even if the next command is sent before receiving the

return data, since PROJECTOR will not be able to receive that command, it does not return a response

to CONTROLLER. Consequently, no error code is also sent.

The following lists the approximate waiting times for PROJECTOR to return the return data after

CONTROLLER sends the command.

.When a communication error occurs, PROJECTOR ignores the data received until now, and set into the

reception standby state.

.For undefined commands or commends determined as invalid by PROJECTOR, PROJECTOR will

send the “NAK”return data to CONTROLLER .

.Take note that when data is written when the input signal of PROJECTOR is unstable, that data (value)

will not be incorporated.

.When INDEX specified SIRCS direct command is transmitted, leave an interval of 45 mSec until the

next transmission. (Do not return the return data (ACK, NAK) when the SIRCS direct command is

received.)

2-7. Approximate Return Waiting Times

The await-return time is approx. 30 msec.

Note: This is the case, unless the communications are interfered anyway.

6VPL-PX11

3. Appendix

< Table 1> <Table 2>

Item Number Data Remarks

Iteme Upper byte Lower byte Data Upper byte Lower byte

VIDEO 00h Set/Get

S VIDEO 01h

INPUT 00h 01h INPUT A 02h

INPUT B 03h

CONTRAST 00h 10h 00h ~ 64h (0 ~ 100)

BRIGHTNESS 00h 11h 00h ~ 64h (0 ~ 100)

COLOR 00h 12h 00h ~ 64h (0 ~ 100)

HUE 00h 13h 00h ~ 64h (0 ~ 100)

SHARPNESS 00h 14h 00h ~ 64h (0 ~ 100)

RGBENHANCER 00h 15h 00h ~ 64h (0 ~ 100)

VOLUME 00h 16h 00h ~ 64h (0 ~ 100)

COLTEMP 00h 17h LOW 00h

HIGH 01h

ASPECT 00h 20h 16 : 9 00h

4 : 3 01h

SCANCONV 00h 21h OFF 00h

ON 01h

PICTUREMUTING 00h 30h OFF 00h

ON 01h

AUDIOMUTING 00h 31h OFF 00h

ON 01h

COMPUTER 00h

INPUTA 00h 32h COMPONENT 01h

VIDEO GBR 02h

GAINRED 00h 80h 00h ~ FFh (0 ~ 255)

GAINGREEN 00h 81h 00h ~ FFh (0 ~ 255)

GAINBLUE 00h 82h 00h ~ FFh (0 ~ 255)

BIASRED 00h 83h 00h ~ FFh (0 ~ 255)

BIASGREEN 00h 84h 00h ~ FFh (0 ~ 255)

BIASBLUE 00h 85h 00h ~ FFh (0 ~ 255)

NO ERROR 00h Get only

LAMP ERROR 01h

FAN ERROR 02h

STATUSERROR 01h 01h COVER ERROR 04h

TEMP ERROR 08h

D5V ERROR 10h

POWER ERROR 20h

WARNING ERROR 40h

Autres manuels pour VPL-PX11

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sony Projecteur

Sony

Sony VPL-BW120S Manuel d'utilisation et d'entretien

Sony

Sony Cineza VPL-HS2 Manuel du propriétaire

Sony

Sony VPL-FX50 Manuel utilisateur

Sony

Sony VPL-VW11HT - Lcd Video Projector Manuel utilisateur

Sony

Sony VPL-PX11 Manuel utilisateur

Sony

Sony VPL-EX100 Manuel utilisateur

Sony

Sony S Series Manuel utilisateur

Sony

Sony VPL-FH65 Manuel utilisateur

Sony

Sony Xperia Touch Mode d'emploi

Sony

Sony VPL-S900U Manuel utilisateur

Sony

Sony VPL-CX75 Manuel utilisateur

Sony

Sony VPL VW50 - SXRD - Projector Manuel utilisateur

Sony

Sony VPL-EW276 Mode d’emploi

Sony

Sony SXRD SRX-S105 Manuel utilisateur

Sony

Sony BRAVIA VPL-VW70 Manuel utilisateur

Sony

Sony VPL-FX51 Manuel utilisateur

Sony

Sony VPLHS3 - Cineza Digital Home Entertainment LCD Front... Guide de démarrage rapide

Sony

Sony VPL-PX32 - Video Projector Manuel utilisateur

Sony

Sony VPL-PX41 Manuel utilisateur

Sony

Sony QUALIA 004 Manuel utilisateur

Sony

Sony VPL-PX41 Manuel utilisateur

Sony

Sony VPL-HW55ES Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-TX7 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur

Epson

Epson PowerLite 810p Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Manuel utilisateur