SOMFY Harmoic Design System II Manuel utilisateur

Programming & Operation Instructions

System II - IR Remote Control

Before You Begin

1. Install window shading complete with HDI motorization into window frame following manufacturers instructions.

2. Install desired battery pack or optional wand as directed. You will notice the green LED flashing.

3. The “memory” is stored in the motor allowing for 1 remote control to program multiple shades.

4. Once programming is complete, should power be removed, the shade will do a long jog once power has been restored and a

command received.

Step 1

Remove “pull tab” from back of

remote control.

Step 2

Using a small paperclip depress the

“MODE BUTTON” located on the

back of the remote control.

The red indicator light on the front of

the remote control should start

flashing in a single-flash pattern.

Step 4 - Set Upper Limit

Hold down the “MIDDLE” button till you see a

double-flashing pattern on the indicator light.

1. Press and hold the “UP” button until shade

reaches desired upper limit.

2. Press and hold the “MIDDLE” button till you

receive a “jog” confirming the upper limit.

Step 5 - Set Lower Limit

1. Press and hold the “BOTTOM” button until

shade reaches desired lower limit.

2. Press and hold the “MIDDLE” button till you

receive a long “jog” confirming the

lower limit.

Step 6 - Set Intermediate Position (IP)

(optional)

(If you choose to do this step later, see Step 9)

1. Press and hold the “UP” button until shade

reaches desired “preferred” position.

2. Press and hold the “OUTER LEFT and/or

RIGHT” button(s) till you receive a “jog”

confirminig the IP.

Step 7 - Exit Installation

Using a small paperclip depress the “MODE BUTTON”

located on the back of the remote control. The red

indicator light on the front of the remote control should stop

flashing. Programming complete!

Continued on reverse

Step 8 - Resetting The Motor

1. At the same time, depress the “MODE” button on the back of

the remote control as well as the “MIDDLE” button on

the front of the remote control and hold for 7+ seconds,

aiming the remote at the motor.

2. The green indicator light on the motor should flash rapidly to

confirm the reset to factory mode.

3. Using the small paperclip depress the

“MODE BUTTON” located on the back of the remote

control. The red indicator light on the front of the remote

control should stop flashing. Begin again at Step 2.

Step 3 - Check/Set Polarity

Aim the remote control at the motor and press the “DOWN” button once and the shade should

“jog” down then up.*

- If it “jogs” up then down, hold down the “UP” button and it will jog down then up.

* If the unit does not respond to check polarity and green LED blinks three (3) times,

reset the motor (Step 8)

www.HarmonicDesignInc.com

DGLYLVLRQRI

Operation Of Remote Control

There are 5 preset limits already programmed into the System II motor once the upper and lower

limits have been set. As well there is the “preferred position” allowing for up to 6 programmed limits.

Point the remote control at the motor and select desired limit based on the guide below:

Continued from front Programming & Operation Instructions ~ System II IR Remote Control

HSYS-7029 © Harmonic Design, Inc. 3/2005

Set to desired

position.

Step 9 - Setting Intermediate Position (IP)

(optional)

1. Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should start flashing in a single-flash pattern.

2. Hold down the “MIDDLE” button on the front of the remote control till you get a double-flash pattern.

3. Using the “UP” or “DOWN” buttons, set your shade to the desired position.

4. Press and hold the “OUTER LEFT and/or RIGHT” button(s) till you receive a “jog” confirming the IP.

5. Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should stop flashing. Programming complete!

Upper Limit 1/4 Limit Middle Limit

3/4 Limit Lower Limit Preferred Position

use the OUTER LEFT, RIGHT or

LEFT & RIGHT button(s) to reach preferred

position.

Additional Feature - Step Tilting

- Position the shade at the lower limit and hold the DOWN button for 1.5 seconds. The shade will “step” backwards

allowing for tilting of vanes in horizontal sheer products. Release when desired position has been reached.

Option 1 - Reset Upper/Lower Limit

- Using the UP or DOWN button, move to limit to be changed.

- Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should start flashing in a single-flash pattern.

- Hold down the MIDDLE button until you see a double-flashing pattern on the indicator light.

- Hold down the UP or DOWN button (depending on which limit being changed) for 1.5 seconds until LED blinks

- Move the shade to new desired limit

- Hold down the MIDDLE button until the shade jogs, confirming new limit

- Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should stop flashing. Programming complete!

Option 2 - Reset Intermediate Position (IP)

- Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should start flashing in a single-flash pattern.

- Hold down the MIDDLE button until you see a double-flashing pattern on the indicator light.

- Using the “UP” or “DOWN” buttons, set your shade to the desired position.

- Press and hold the “OUTER LEFT and/or RIGHT” button(s) till you receive a “jog” confirming the IP.

- Using a small paperclip depress the “MODE BUTTON” located on the back of the remote control. The red

indicator light on the front of the remote control should stop flashing. Programming complete!

Autres manuels SOMFY Télécommande

SOMFY

SOMFY Telis 1 RTS Pure Manuel utilisateur

SOMFY

SOMFY Telis 1 Soliris RTS Pure Manuel utilisateur

SOMFY

SOMFY INTEO TELIS 4 RTS Manuel utilisateur

SOMFY

SOMFY Nina Timer io Manuel utilisateur

SOMFY

SOMFY Situo 1 Soliris RTS II Manuel utilisateur

SOMFY

SOMFY Centralis RTS Manuel utilisateur

SOMFY

SOMFY inis RT Manuel utilisateur

SOMFY

SOMFY Situo 1 RTS Manuel utilisateur

SOMFY

SOMFY SITUO 1 VARIATION Instructions d'utilisation et d'entretien

SOMFY

SOMFY Telis Composio RTS Manuel utilisateur

SOMFY

SOMFY Telis Composio io Manuel utilisateur

SOMFY

SOMFY SITUO 1 VARIATION Manuel utilisateur

SOMFY

SOMFY FREEROLL RTS Manuel utilisateur

SOMFY

SOMFY KEYPOP 2 RTS Manuel utilisateur

SOMFY

SOMFY KeyGo io Manuel utilisateur

SOMFY

SOMFY KEYTIS INTERIOR Manuel utilisateur

SOMFY

SOMFY Telis 5 Modulis RTS Silver 1810663 Manuel utilisateur

SOMFY

SOMFY Telis 6 Chronis RTS Guide d'installation

SOMFY

SOMFY Situo 1 RTS Guide d'installation

SOMFY

SOMFY Easy Sun io Manuel utilisateur

SOMFY

SOMFY Rollixo Optimo RTS Manuel utilisateur

SOMFY

SOMFY INTEO TELIS 1 RTS Manuel utilisateur

SOMFY

SOMFY Oximo RTS Manuel utilisateur

SOMFY

SOMFY inteo CENTRALIS RTS Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation