SMART-AVI QKVM4K Manuel utilisateur
QKVM4K
Quick Start Guide
A full Manual can be downloaded from
www.smartavi.com/QKVM-4K/
Ultra-HD Multiviewer &
KVM Switch
with Dual Video Outputs
TECHNICAL SPECIFICATIONS
VIDEO
Format HDMI
Host Interface (4) HDMI 19-pin (female)
User Console
Interface (2) HDMI 19-pin (female)
Max Resolution 3480 x 2160 @ 60Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type USB 2.0, 1.1, and 1.0 w/ internal
hub
Input Interface (4) USB Type B
Output Interface
(2) USB 1.1 Type A for KVM Devices
(2) USB 2.0 Type A Transparent
AUDIO
Input (4) Connector Stereo 3.5mm Fe-
male
Output (1) Connector Stereo 3.5mm Fe-
male
POWER
Power Requirements 12V DC, 3A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CONTROL
Front Panel Push Buttons with LED indicators
RS-232 Via Serial @ 115200 bps
Hot Keys Via Keyboard
OTHER
Emulation Keyboard, Mouse and Video
WHAT’S IN THE BOX
PART NO. QTY DESCRIPTION
QKVM4K 1 4-port, HDMI Multiviewer KVM
Switch
PS12VDC3A 1 12V DC, 3A power adapter with
center-pin positive polarity.
1 Quick Start Guide
NOTICE
The information contained in this document is subject
to change without notice. SMART-AVI makes no war-
ranty of any kind with regard to this material, includ-
ing but not limited to, implied warranties of merchant-
ability and fitness for particular purpose. SMART-AVI
will not be liable for errors contained herein or for
incidental or consequential damages in connection
with the furnishing, performance or use of this materi-
al. No part of this document may be photocopied,
reproduced, or translated into another language with-
out prior written consent from SMART-AVI, Inc.
Toll Free: (800) AVI-2123
Phone: (702) 800-0005
2455 W. Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
smartavi.com
4-PORT HDMI MULTIVIEWER
& KVM SWITCH WITH AUDIO,
USB 2.0, AND PREVIEW
HARDWARE INSTALLATION
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use HDMI cables to connect the HDMI output ports from each computer to the corresponding HDMI-I IN ports of
the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the
unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the computers to the
AUDIO IN ports of the unit.
5. Connect monitors to the HDMI-I OUT console ports of the unit using HDMI cables.
6. Connect a USB keyboard and mouse in the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on all the
computers.
EDID LEARN
The QuadKVM4K has 3 preset EDIDs that can be trig-
gered from the front panel by pressing:
Aand 1simultaneously will invoke IPG—1080p
Aand 2simultaneously will invoke IPG - 4K
SYSTEM CONTROL
There are four ways to control the QKVM4K: Keyboard
HotKeys, RS-232 Serial Commands, OSD Menu and
Front Panel Buttons.
The settings for the serial connection are as follows:
Baud rate: 115200; Data Bits: 8; Parity: None; Stop
Bits: 1; Flow Control: None.
The following commands can be used:
Command HotKey RS-232
Switch KVM [CT][CT]m[#]<CR> //m[#]<CR>
Full Screen [CT][CT]f[#]<CR> //f[#]<CR>
PiP [CT][CT]p[a][b]
<CR>
//p[a][b]
<CR>
T-Quad [CT][CT]t[#]<CR> //t[#]<CR>
Quad [CT][CT]q<CR> //q<CR>
Audio Only [CT][CT]a[#]<CR> //a[#]<CR>
KM Only [CT][CT]c[#]<CR> //c[#]<CR>
USB Only [CT][CT]u[#]<CR> //u[#]<CR>
Learn EDID [CT][CT]e<CR> //e<CR>
SW Reset [CT][CT]r//r <CR>
Status Query N/A //?? <CR>
Chart Key
[CT] = Ctrl
<CR> = Carriage Return (Enter Key)
Command HotKey
OSD ON/OFF [CT][CT]o <CR>
OSD UP
↥(UP arrow)
OSD DOWN
↧(DOWN arrow)
OSD LEFT ↤(LEFT arrow)
OSD RIGHT ↦(RIGHT arrow)
OSD Enter [ENTER]
OSD Esc [ESC]
OSD MENU
Important: When in OSD Menu, all keyboard
and mouse functionality will be blocked from
the computer and only used for the OSD com-
mands. After exiting the OSD menu, all key-
board and mouse functionality will be restored.
NOTE: When entering one of the Function com-
mands, the Enter Key must be pressed for the
function to take effect
Autres manuels pour QKVM4K
1
Autres manuels SMART-AVI Changer
SMART-AVI
SMART-AVI SM-DVN-82X Manuel utilisateur
SMART-AVI
SMART-AVI UHDN-4P Duo Manuel utilisateur
SMART-AVI
SMART-AVI DVR4X4S Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-2S Manuel utilisateur
SMART-AVI
SMART-AVI SM3-UHX-2D Manuel utilisateur
SMART-AVI
SMART-AVI SM-DPN-4D Manuel utilisateur
SMART-AVI
SMART-AVI DPN-4QUAD Manuel utilisateur
SMART-AVI
SMART-AVI D2H-4P Duo Manuel utilisateur
SMART-AVI
SMART-AVI DV-SW8-p Manuel utilisateur
SMART-AVI
SMART-AVI SM-UHN-2S Manuel utilisateur
SMART-AVI
SMART-AVI StretcherPro Manuel utilisateur
SMART-AVI
SMART-AVI DPN-4QUAD Manuel utilisateur
SMART-AVI
SMART-AVI UHDN-4P Duo Manuel utilisateur
SMART-AVI
SMART-AVI HDN-8P Manuel utilisateur
SMART-AVI
SMART-AVI HDN-4 Quad Manuel utilisateur
SMART-AVI
SMART-AVI UHDN-4P-DUO Manuel utilisateur
SMART-AVI
SMART-AVI D2H-4P-QUAD Manuel utilisateur
SMART-AVI
SMART-AVI SKM-08-S Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-4Q Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-4D Manuel utilisateur
