Skytech SkyMaker H Series Manuel utilisateur

Catalogue

Hardware Assembly of Skymaker H Series。

Introduction - 1 -

1. Bottom Corner Fittings Assembly................................................... - 1 -

2. Top Corner Fittings Assembly........................................................ - 8 -

3. Feedmachine Assembly ................................................................ - 14 -

4. Limit Switches Assembly ............................................................. - 18 -

5. Tackles Assembly......................................................................... - 19 -

6. Long Aluminium Fittings Assembly............................................. - 21 -

7. Nozzle Assembly.......................................................................... - 22 -

8. Automatic Level Controller Assembly.......................................... - 25 -

9. Top, Middle and Bottom Components Assembly.......................... - 29 -

10. The Electric Wire Road............................................................... - 31 -

11. Tackles Connect to Automatic Level Controller Assembly......... - 33 -

12. Timing Belt Assembly ................................................................ - 35 -

13. LCD Screen Assembly................................................................ - 37 -

14. Flat Cable on Cardinal Plate Assembly....................................... - 40 -

15. Fix the Cardinal Plate & External Plate Assembly ...................... - 44 -

16. Glass & Feeding Pipe Assembly................................................. - 46 -

- 1 -

Hardware Assembly of Skymaker H Series

First, let us begin by introducing the fittings of Skymaker H Series.

Name

Quantity

Name

Quantity

Hexagon Truss Head Screw

M4*8

0.9 ゜step angle with 42

micro-stepping Motor (long

wire)

Hexagon Truss Head Screw

M4*10

Limit Switches (include wire

& connector post)

Hexagon Truss Head Screw

M4*20

Cooling Fan

Hexagon Cup Head Screw

M2.5*12

Nozzle Heated Pipe

Hexagon Cup Head Screw

M3*8

Nozzle Temperature

Detecting Wire

Hexagon Cup Head Screw

M3*12

Cardinal Plate

Hexagon Cup Head Screw

M3*20

LCD Plate

Hexagon Cup Head Screw

M5*25

Carbon Fiber Shaft (include

plain bearings*2)

Hexagon Socket Set

Screw3*4

2GT 16 teeth Synchronizing

Wheel

M3 Nut

Feeding Synchronizing

Wheel

M4 Nut

F623ZZ Single Side Flange

Bearing

M4 Square Nut

608ZZ Bearing

M5 Nut

Rubber Pulley

M4 Washer

Heating Al Block

Bottom Corner Fitting

Radiating Al Block

Top Corner Fitting

Feeding Pipe

Automatic Level Controller

Nozzle 0.4 mm

- 2 -

Automatic Level Controller

Quick Coupler (big)

Automatic Level Controller

Quick Coupler (small)

Tackle (include timing belt

connector)

2020 Al Fitting (long)

Extruder Connector A

2020 Al Fitting (short)

Extruder Connector B

2GT Timing Belt (motor axle

transmission)

Limit Switch Stop

Coiler

Fixing Board of Cardinal

Plate

PTFE Pipe

LCD Plate Support

Round Glass

External Plate (power source

& transmission header)

USB Line

0.9 ゜step angle with 42

micro-stepping Motor (short

wire)

DC Stabilized Power Source

3P Connector Base

2P Connector Base

- 3 -

The following are 16 steps for H Series assembly:

1. Bottom Corner Fittings Assembly

2. Top Corner Fittings Assembly -

3. Feeding Machine Assembly

4. Limit Switches Assembly

5. Tackles Assembly

6. Long Aluminum Fittings Assembly

7. Nozzle Assembly

8. Automatic Level Controller Assembly

9. Top, Middle and Bottom Components Assembly

10. The Electric Wire Road

11. Tackles Connect to Automatic Level Controller Assembly

12. Timing Belt Assembly

13. LCD Screen Assembly

14. Flat Cable on Cardinal Plate Assembly

15. Fix the Cardinal Plate & External Plate Assembly

16. Glass & Feeding Pipe Assembly

Now, let’s start to assemble Skymaker H Series!

Bottom Corner Fittings Assembly

Fittings：0.9゜step angle with 42 micro-stepping Motor (short wire)*1、Bottom

Corner Fitting *1、2020 Al Fitting (short) *2、2GT 16 teeth Synchronizing Wheel*1、

Hexagon Socket Set Screw (3*4)*2、M4 Square Nut*10、Hexagon Cup Head Screw

(M3*8)*4、Hexagon Truss Head Screw (M4*10)*10

- 4 -

Assembly：

First, assemble the 2GT 16 teeth Synchronizing Wheel and the 0.9゜step angle with

42 micro-stepping Motor (short wire). Then screw two Hexagon Socket Set Screw

(3*4) on the 2GT 16 teeth Synchronizing Wheel tightly and one of the two Hexagon

Socket Set Screw (3*4) should be screwed on the plane side.

Use Hexagon Truss Head Screw (M4*10) and M4 Square Nut to assemble the two

side with eight holes (M4 Square Nut should be outside) but do not screw them tightly.

They have to be screwed with 2020 Al Fitting (short) later.

In the following picture, use Hexagon Truss Head Screw (M4*10) and M4 Square Nut

to screw two holes. First, put M4 Square Nut on finger and aim at a hole in the

Bottom Corner Fitting. Then use Hexagon Truss Head Screw (M4*10) to screw it

from outside but do not screw them tightly. They have to be screwed with 2020 Al

Fitting (long) later.

- 5 -

In the following picture, these four holes are used to fix the Bottom Corner Fitting and

0.9゜step angle with 42 micro-stepping Motor (short wire).

(the finger-pointed place is the bottom)

Aim at 0.9゜step angle with 42 micro-stepping Motor (short wire) and the Bottom

Corner Fitting. Then use Hexagon Cup Head Screw (M3*8) to screw them tightly.

Assemble 2020 Al Fitting (short) on the same side and then screw Hexagon Truss

Head Screw (M4*10) tightly.

- 6 -

2020 Al Fitting (short) of the three Bottom Corner Fitting should be screwed on the

same side.

Assemble the three Bottom Corner Fitting and put them to be a triangle.

Wedge the three Bottom Corner Fitting to a well-screwed M4 Square Nut. Be careful

not to pinch the wires.

(Wedging them to two well-screwed M4 Square Nut at a time is not acceptable.)

- 7 -

Wedge the three Bottom Corner Fitting to the second well-screwed M4 Square Nut

after finish the first one.

After wedge the M4 Square Nut of three Bottom Corner Fitting well, screw Hexagon

Truss Head Screw (M4*10) tightly.

Now, we finish the assembly of Bottom Corner Fitting!

- 8 -

2. Top Corner Fittings Assembly

Fittings：Top Corner Fitting*1、2020 Al Fitting (short)*1、F623ZZ Single Side Flange

Bearing*2、M4 Square Nut*5、Hexagon Cup Head Screw (M3*20)*1、Hexagon Truss

Head Screw (M4*10)*5、M4 Nut*1、Hexagon Truss Head Screw (M4*20)*1、M3

Nut*1、M4 Washer*1。

Assembly：

Assemble the tackle of timing belt used.

Make Hexagon Cup Head Screw (M3*20) go through the central hole.

Hitch the two F623ZZ Single Side Flange Bearing and stack these two together. The

side with border has to be outside.

Table des matières

Autres manuels Skytech Imprimante 3D

Skytech

Skytech 3D PANDORAS Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur