SkyLink PT-434 Manuel utilisateur
Skylink
will not
-be
held
liable or responsible for
any misuse or application
of this product other than
for its intended use.
8
PANtC
TRANSMITTER
USER’S INSTRUCTIONS
(Model PT-434)
The Panic Transmitter con-
veniently fits on any
key-
chain or necklace.
it
allows
you to activate Skylink’s
receivers (Secuftiy Control
Panel
SGOO1,
SC-002,
Emerge&y Dialer
AD+,
Audio
Alarm
AA-433,
Silent
Alarm SW-433) from a
maximum distance of
approximately 100 feet
from the receiver. This
transmitter is water
resistant and shock resis-
tant, it allows you to
cany
this transmitter all the time.
1.
2.
3.
4.
5.
6.
Enter the current
MPIN
(Master Personal Identification Number)
on the SC-001, SC-002.
Press [B].
Press the number key to identify which zone to add the panic
transmitter to. Do not program the transmitter to zone
1,2,3,4.
The panic transmitter is designed to be programmed in zone 5
for SC-001 and zone 9 for SC-002.
Therefore, press
[5]
for SC-001 and press
[9]
for
SC-002.
The zone light(s) will flash for eight seconds.
While the zone light(s) are flashing, press [ *I. Now both the
green and red lights flash for 30 seconds.
While the zone lights are flashing, activate the panic transmitter
by pressing the button on the transmitter. The red LED light of
the sensor will flash. You will hear a long beep from the control
panel, the zone light will stop flashing and the panic transmitter
will now communicate to that zone.
The Panic Transmitter operates on three 3-volt
lithium
batteries that are installed at the
factory. The battery life of these lithium batteries is approximately three years. There are
two screws on the back of the transmitter that hold the top and bottom case together.
Recommendation: Test your transmitter periodically to ensure that all the batteries are
working.
To replace the Panic Transmitter batteries:
?
_
Undo the two screws on the back of the transmitter. The bottom case will then come
off.
2. Take out all the old batteries using a small screwdriver or a pen.
3. Place the new batteries in position. The positive end should be facing upward as you
place the batteries in the transmitter (refer to diagram)
4. Close the battery cover and reinsert two screws.
Press [L],
[5]
when in clock.mode, the display will_
show
“L5
Id
codE”.
Activate the panic transmitter
within
5 seconds by
pressing the button on the transmitter. The red LED
light of the transmitter will be on when the button is
pressed. The display will return to clock mode once
the panic transmitter has been learned.
If the button of the panic transmitter is pressed, it
will trigger the Emergency Dialer and start
dialing-
the preset phone numbers (refer to AD-433, AD-002
User’s Instruction for details).
-
In an emergency, you can
activate the
Skylink
re-
ceivers using the Panic
Transmitter. Move the slid-
ing cover and press the
panic button for one second.
This will activate the “learned”
Skylink receiver(s).
-
Note: Make sure you press
down on the transmitter for
one full second or the sys-
tem may not respond.
The Remote Control is
approved by the FCC and
it complies with Part 15
of the FCC Rules. Its
operation is subject to the
following two conditions
:
I.
This device may not
cause harmful inter-
ference.
WARNING:
Changes or modification3
to this unit not expressly
approved by the party res
ponsible of compliance
could void the user’s
authority to operate the
equipment.
2. This device must accept
any interference that
may cause undesired
operation.
Table des matières
Autres manuels SkyLink Émetteur
SkyLink
SkyLink 18T4 Manuel utilisateur
SkyLink
SkyLink TB-318 Manuel utilisateur
SkyLink
SkyLink HW-434 Manuel utilisateur
SkyLink
SkyLink G6T2 Manuel utilisateur
SkyLink
SkyLink GG-318 Manuel utilisateur
SkyLink
SkyLink 318K Manuel utilisateur
SkyLink
SkyLink 4B-201 Manuel utilisateur
SkyLink
SkyLink KP-433 Manuel utilisateur
SkyLink
SkyLink TB-318 Manuel utilisateur
SkyLink
SkyLink TC-318-1 Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
