Sim2 M.150S Manuel utilisateur

SIM2 Multimedia

M.150S

User Guide

Contents

3Important information

About this User Guide

Safety

3D Content

Environment

Notice

7Chapter 1: Introduction

Key Features and Benefits

System Components

Optional Accessories

9Chapter 2: Overview

Remote Control

Projector Keypad

Connections

3D RF Emitter

3D Glasses

14 Chapter 3: Installation

Location

Mounting

Connections

Switching On and Off

19 Chapter 4: Operation

Viewing 3D Content

3D Menu

Input Menu

Main Menu

Picture

Image

Setup

Memories

Info

Quick Menus

Messages

35 Chapter 5: Troubleshooting

37 Chapter 6: Specifications

39 Chapter 7: Projection Distances

40 Chapter 8: Dimensions

M.150S

User Guide

Important information

About this User Guide

This User Guide describes how to set up and operate the M.150S LED 3D projector.

Information contained in this User Guide may be updated from time to time due to

product improvements and customer feedback. Visit www.sim2.com to find the latest

version of this document.

This document contains proprietary information protected by copyright. All rights are

reserved.

All trademarks and registered trademarks are the property of their respective owners.

Safety

To reduce the risk of electrocution, disconnect the power cord on the

rear panel before removing the top cover of the projector. For technical

service refer to trained personnel authorized by the manufacturer.

Read this guide

Read all chapters of this guide carefully before switching on the projector. This guide

provides basic instructions for operating the M.150S projector. Installation,

preliminary adjustments and procedures that necessitate the removal of the top cover

and contact with electrical components must be performed by authorized, trained

technicians. To ensure safe operation and long term reliability use only the power

cords supplied by the manufacturer. Observe all warnings and precautions. Keep this

guide for future consultation.

Do not touch internal parts of the projector

Inside the housing there are electrical parts carrying dangerously high voltages and

parts operating at high temperature. Never open the housing. Entrust all servicing and

repair work to a SIM2 Authorized Service Center. Opening the housing voids the

warranty.

Disconnect the appliance from the power supply

The device that disconnects the projector from the mains is the power plug. Ensure

that the power cord plugs and the electrical outlets are easily accessible during

installation operations. Pull the plug, not the cord, to disconnect the projector from

the mains. Use only the specified power supply. Connect the projector to a mains

electrical supply with rated voltage of between 100-240 V AC, 50/60 Hz and equipped

with a protective earth connection. If you are not sure of your domestic mains rating,

contact an electrician. Take care to avoid overloading the power socket and any

extension leads.

Changing the fuses

Before changing the fuse, disconnect the projector from the mains power supply. The

fuse compartment is next to the power supply connector. Remove the fuse holder

Important information M.150S

User Guide

with a flat head screwdriver and replace the fuse. Fit the replacement fuse. Use only

type T 10 A L H fuses for the projector.

Be careful with cables

Make sure cables are routed so that people are not impeded or become a trip hazard.

Keep all cables away from children. Install the projector as close to the wall socket as

possible. Avoid stepping on power cords, make certain they do not become tangled,

and never jerk or tug them; do not expose them to sources of heat, and make sure

they do not become knotted or crimped. If the power cords become damaged, stop

using the projector and request the assistance of an authorized technician.

Disconnect the projector from the mains power during electrical storms and when

not in use

To prevent damage from lightning strikes in the vicinity, disconnect the projector

during storms or when the projector is going to be left unused for a long time.

Avoid contact with liquids and exposure to damp

Do not use the projector near water (sinks, tubs and so on); do not place objects

containing liquids on or near the projector and do not expose it to rain, humidity,

drops of water or sprays; do not use water or liquid detergent to clean it.

Place the projector on a stable surface

Place the projector on a stable surface or use a suitable ceiling mounting bracket.

Never place the projector on its side or rear, on the lens or top panel.

Do not allow the projector to overheat

To prevent overheating, allow a free space of at least 0.25 m (10 in.) on the left, right

and rear sides of the projector. Do not obstruct the ventilation slots. Do not place the

projector near heat sources such as heaters, radiators or other devices (including

amplifiers) that generate heat. Do not place the projector in an area where there is

insufficient space (shelving units, bookshelves and so on) and in general avoid placing

it in poorly ventilated areas as this may prevent sufficient cooling.

Never look directly into the projection lens

Never look directly into the lens when the projector is on as the intense light may

damage your eyes. Take particular care that children cannot do so.

LED LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LED PRODUCT

P ≤0.88 mW λ= 452 nm

ICE 60825-1:1993 + A1:1997 + A2:2001

EN 60825-1:1994 + A2:2001 + A1:2002

Take special care regarding movement of the lens

Do not place objects in the slots on the side of the lens and also ensure that vertical

lens movements are not impeded by external objects.

Important information M.150S

User Guide

Do not insert objects through the openings in the projector

Make sure that no objects are inserted inside the projector. If this should occur,

disconnect the projector from the power supply immediately and call an authorized

technician.

Power saving

We advise disconnecting the projector from the power supply when not in use. In this

way you will achieve considerable power savings while at the same time protecting

internal electrical parts from wear.

3D Content

Discomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disori-

entation) may be experienced while watching 3D content. In this case, stop watching

and consult a doctor if symptoms are severe.

Consult a doctor before allowing young children (especially those under six years old)

to watch 3D content as their visual system is still under development.

Monitor children (including teenagers) watching 3D content, as they are more at risk

of experiencing discomfort and less inclined to report symptoms.

Individuals who may be susceptible to epileptic seizures or strokes (on the basis of

personal and family history) should consult a doctor before watching 3D content.

All viewers should take regular breaks from watching 3D content. Length and

frequency of these breaks may vary from person to person.

Environment

This product contains materials derived from natural resources during its

manufacture. It may contain materials that constitute a health and environmental

hazard. To prevent harmful materials from being released into the environment and to

promote the use of natural materials, SIM2 provides the following information

regarding the disposal and recycling of the product.

Waste electrical and electronic materials (WEEE) should never be disposed of in

normal urban waste disposal facilities.

The label on the product, shown here, indicating a canceled garbage can,

is intended to remind you that the product requires special handling at

the end of its service life. Materials such as glass, plastic and some

chemical compounds are recoverable and can be recycled for reuse.

Observe the following instructions:

•When you no longer wish to use your electrical and electronic equipment,

take it to your local waste disposal facility for recycling.

•You may return your old equipment to your SIM2 Authorized Dealer free of

charge when you buy a new product that is equivalent or has the same

functions as the old one. Contact SIM2 to find your local dealer.

•If you need more information regarding recycling, reuse and product

exchanges, contact SIM2 customer service.

Important information M.150S

User Guide

Lastly we suggest further measures to safeguard the environment, such as recycling of

internal and external packaging (including that used for shipping) in which the product

was delivered. With your help, we can reduce the amount of environmental resources

required to make electric and electronic equipment, reduce the use of waste tips for

used equipment and, in general, improve our quality of life by making sure that

hazardous materials are correctly scrapped. Incorrect treatment of the product at the

end of its service life and failure to follow the above disposal instructions are

punishable under local legislation.

Notice

The appliance has been subjected to exhaustive operating tests by SIM2 to guarantee

the highest quality. The projector light source life should thus initially be around 30-60

hours. In addition to the customary checks, the Quality Control department also runs

additional statistical tests before shipment. In such cases, the packaging may show

signs of having been opened, and the hours of light source operation may prove to be

higher than those normally shown when only standard tests are performed.

As the optical system of the M.150S is extremely compact and has the purpose of

developing very high brightness and contrast, it is possible that a small quantity of

light is visible outside of the projection area and will vary depending on the type of

lens used and the zoom and shift setup. This characteristic of the optical system is to

be deemed as normal. In order to reduce this effect SIM2 recommends that the area

surrounding the projection screen is as dark as possible.

Important information M.150S

User Guide

1 Introduction

Building on the success of SIM2's award winning M.150 platform, the brand new

M.150S projector represents the culmination of over 2 years of research in the field of

engineering performance, and component selection.

The LED top-of-the-line M.150S is a projector where each component has been pre

tested and hand-selected for its excellence and reliability, and fine-tuned to deliver

unprecedented picture quality and performance.

Its superb colorimetry and extreme accuracy far exceed the same characteristics of

the available projectors in the market based on the same technology.

The projector features improved color space specifications for a wide variety of

applications, including AdobeRGB and CINEMA, producing images with amazing

clarity, contrast and realism.

The M.150S is a high-end compact 3D single unit projector that incorporates PureLED

technology, a combination of single chip DLP from Texas Instruments, three individual

high power LEDs, a new light engine, and a dedicated video processing.

PureLED technology allows the projector to deliver clearer, brighter and more vibrant

images, a wider and more consistent color gamut, and full-on/full-off contrast up to

100,000:1.

The M.150S is able to emulate the best 3D cinema projection systems, in terms of

color fidelity, definition and depth of image. These are all conveyed accurately, as is

the fluid motion of fast-action movies and sports. This all adds up to an incredible 3D

experience at home.

The M.150S is designed for use with large screen sizes – up to 4 m (14 ft.) wide. A

choice of two high quality glass lenses (T1 and T2) is available, giving the projectors a

total throw ratio of 1.5-3.9:1.

1 Introduction M.150S

User Guide

To aid calibration SIM2’s Live Color Calibration software enables complete control

over:

•primary, secondary and white point color coordinates

•gamma tables

allowing calibration experts to accurately calibrate the final image via a user-friendly

application for Windows-based computers.

Key Features and Benefits

•high picture quality: SIM2 renown image processing and the latest 0.95 in.

1080p DMD from Texas Instruments

•precision optics: compact die-cast light engine with precision glass optics and

motorized zoom, focus and lens shift

•longer light source life: typical life estimated around 30,000 hours

•richer and more saturated colors: wider and more consistent color gamut and

full-on/full-off contrast up to 100,000:1

•extremely quiet level of operating noise: liquid-cooling system

•quick on/off: warm-up and cool-down periods require seconds not minutes

•artifact-free fast-action images: SIM2 PureMotion processing

•high resolution: actual full HD 3D images, without blur and ghosting

•comfortable 3D viewing: high brightness ghost-free sharp images

•immersive 3D effect: large screen sizes thanks to high brightness images

•3D wide viewing angle: stereo separation independent from viewing angles

•screen flexibility: no constraints in the choice of the screen material

•compatibility: no need of dedicated sources and preprocessing for 3D viewing

System Components

Your M.150S DLP projector ships with the following items:

•1 x backlit remote control unit (with four AAA/LR03 batteries)

•3 x AC power cords (US, EU and UK), 2 m (6.6 ft.) long

•3 x jacks for 12 V output connectors

•1 x User guide (this document)

If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as

possible. Keep the original packaging in case anything has to be shipped.

Optional Accessories

•VISUSRF-SYSTEM-ACC (4 SIM2 Visus 3D RF glasses and 1 RF emitter for SIM2

Visus 3D RF glasses)

•Projector ceiling bracket

•Anamorphic lens systems (fixed or motorized)

1 Introduction M.150S

User Guide

2 Overview

❶Projection Lens Available in two versions: T1 (1.5:1 to 2.1:1) and T2 (2.1:1 to 3.9:1)

❷Front IR Sensor Receives infrared signals from the remote control unit

❸❹ Ventilation slots Ensure reliable operation and protect the projector from

overheating. Make sure they are not obstructed.

❺Indicator light and

status display

Show projector status as follows:

Indicator light:

•solid red = low power standby

•solid orange = fast switch on standby

•flashing green and red = initialization or cooling down

•solid green = normal operation

Status display:

•88 = initialization

•black = normal operation

•two-digit code = error status (displayed code may be useful

for troubleshooting)

❻Rear IR Sensor Receives infrared signals from the remote control unit

❼Keypad Controls the main functions of the projector. Pull the cover to access

the keys. See “Projector Keypad” on page 11 for a detailed

description of their functions.

❽AC receptacle and

main power switch

Plug here the female end of the AC power cord that is appropriate in

your area. Switches the projector on or off.

❾Connector Panel Contains the connections for all input, control and output signals.

See “Connections” on page 12 for details

2 Overview M.150S

User Guide

Remote Control

turn backlight on for about 5 seconds

turns the projector off

1-9 select inputs and turn the projector

0enters OSD Input menu and turns

the projector on

●OK enters submenus, confirms

actions

ESC exits OSD

▴

◂▸

▾

select menu items, adjust settings or

cycle through the test patterns

+ / -

enter OSD Main menu and select

the desired section, each press of

the key selects the next tab in the

II 3D enters 3D menu

Memory enters Memories menu

F1, F2 perform user-defined actions

(default assignments are: F1 = Zoom,

F2 = Focus)

Info displays projector Info

A Auto performs Auto Adjustment

Aspect enters Aspect Quick menu

Not used

Custom Remotes

You can use your own IR remote control to control your M.150S projector.

•If you are using a remote control with learning capabilities, use the projector

remote control to teach the commands to your remote.

•If you are using a programmable remote control, the setup software probably

allows importing of Pronto Hex codes. See SIM2 M.150S IR Control for a list of

all the projector codes in Pronto Hex format, including a number of discrete

codes for:

◦Aspects

◦Memories

◦3D Controls (3D Mode and Input Formats)

2 Overview M.150S

User Guide

Table des matières

Autres manuels Sim2 Projecteur

Sim2

Sim2 Grand Cinema HT200 DMF Manuel d'utilisation

Sim2

Sim2 AR Manuel utilisateur

Sim2

Sim2 Grand Cinema C3X LUMIS 3D Manuel utilisateur

Sim2

Sim2 DLINE D35 Manuel d'utilisation

Sim2

Sim2 PRO5000 Manuel utilisateur

Sim2

Sim2 HT300 XTRA-H Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT300 Link Manuel d'utilisation

Sim2

Sim2 xTV Series Manuel utilisateur

Sim2

Sim2 Grand Cinema HT C3X-LINK Manuel d'utilisation

Sim2

Sim2 DOMINO DTV S Manuel utilisateur

Sim2

Sim2 C3X 1080 Manuel d'utilisation

Sim2

Sim2 C3X1080 Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT 200 Manuel utilisateur

Sim2

Sim2 GRAND CINEMA HT5000 Manuel utilisateur

Sim2

Sim2 Grand Cinema HT305 E Manuel utilisateur

Sim2

Sim2 SVD800 HD Millennium Manuel d'utilisation

Sim2

Sim2 DLP Video Projector C3X Link Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT300 Link Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT380 Manuel d'utilisation

Sim2

Sim2 HT 280E Manuel d'utilisation

Sim2

Sim2 DLINE D35 Manuel utilisateur

Sim2

Sim2 M.150 Manuel utilisateur

Sim2

Sim2 E-LINK HT300 Manuel d'utilisation

Sim2

Sim2 C3X1080 Manuel d'utilisation

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur