Siko Easy Touch Control ETC5000 Manuel utilisateur

User manual

Easy Touch Control

ETC5000

ETC5000 xDate: 12-11-2019 Page 2 of 23 Art. no. 86986 Mod. status 252/19

1Safety indication ........................................................................................................................... 3

2System design.............................................................................................................................. 3

3General Information...................................................................................................................... 3

3.1 AXIS.......................................................................................................................................... 3

3.2 RECIPE...................................................................................................................................... 4

3.3 OPERATION /PAGE NAVIGATION.................................................................................................. 4

4Login............................................................................................................................................. 5

5Main functions / start screen......................................................................................................... 5

6Set Positioning.............................................................................................................................. 6

6.1 RECIPE SELECTION .................................................................................................................... 6

6.2 RECIPE POSITIONING.................................................................................................................. 7

7Axis Positioning ............................................................................................................................ 8

7.1 CHANGING THE SETPOINT OF AN AXIS AND INCHING MODE ............................................................ 8

8Settings......................................................................................................................................... 9

8.1 DEVICE MANAGER.................................................................................................................... 10

8.1.1 Bus-Scan........................................................................................................................... 10

8.1.2 Device manager................................................................................................................. 11

8.1.3 Change the parameters of an axis/device......................................................................... 12

8.1.4 Functions of IO20 .............................................................................................................. 13

8.2 RECIPE MANAGEMENT –EDITING RECIPES................................................................................. 15

8.2.1 Add recipe.......................................................................................................................... 15

8.2.2 Edit recipe.......................................................................................................................... 16

8.3 ETC5000 SETTINGS /SOFTWARE UPDATE................................................................................ 16

8.3.1 Software Update................................................................................................................ 17

8.4 USER ACCOUNTS ..................................................................................................................... 19

8.5 SECURITY LEVEL...................................................................................................................... 20

8.6 IMPORTING AND EXPORTING..................................................................................................... 20

8.7 LOG FILE ................................................................................................................................. 21

9Commissioning ETC5000........................................................................................................... 22

10 Data backup and system maintenance ...................................................................................... 23

10.1 PREVENT DATA LOSS –DATA BACKUP....................................................................................... 23

10.2 SYSTEM MAINTENANCE............................................................................................................. 23

ETC5000 xDate: 12-11-2019 Page 3 of 23 Art. no. 86986 Mod. status 252/19

1 Safety indication

NOTICE

None of the inputs or outputs of ETC5000 and IO20 are intrinsically safe

inputs or outputs. Therefore, do not use the ETC5000 system for safety-

relevant applications!

2 System design

ETC5000 (Easy Touch Control) is a complete system for the control of format adjustment. It is

suitable for controlling up to 31 bus-compatible position indicators and actuators via

SIKONETZ5. The system is freely programmable; digital position indicators can be used for

monitored format adjust and actuators can be employed for fully automated format adjustment.

You can also easily combine both device classes or gradually expand the system to include 31

devices (see chapter 8.1: Device manager).

There are input and outputs for reading in additional machine states and outputting the current

state of ETC5000. For this purpose, IO20 is available with 8 inputs and 8 outputs.

ETC5000 offers the opportunity to store in recipes multiple machine settings for different

products or formats. Once created, recipes can be selected as required. ETC5000 monitors the

positions of all axes and adjusts them automatically if drives are used (see chapter 6: Set

Positioning).

Moreover, ETC5000 provides the opportunity to specify setpoints for individual axes and to

position individual drives (see chapter 7: Axis Positioning).

The parameters of the connected devices can be changed via ETC5000 to enable the

adjustment of the system to the individual application (see chapter 8.1.3: Change the

parameters of an axis/device).

The system is perfected by unique user accounts and a log function, which records important

system events (see chapter 8.4: User accounts and chapter 8.7: Log file).

3 General Information

3.1 Axis

Every SIKONETZ5 subscriber linked to ETC5000 has its unique device address and serves for

monitoring or adjusting an axis. This is the reason why the connected devices with their device

addresses and their device symbols in ETC5000 are called axes.

NOTICE

A unique device address must be set for all devices connected via the

SIKONETZ5 bus!

The SIKONETZ5 device address must be set directly on the connected device. For the

individual procedures please refer to the User manual of the relevant device.

As a special feature, the inputs and outputs of IO20 are not designed for monitoring a single

axis. In fact, they are designed for monitoring and displaying the overall system. Nevertheless,

IO20 is treated as an axis in ETC5000 because it has a unique SIKONETZ5 bus address.

ETC5000 xDate: 12-11-2019 Page 4 of 23 Art. no. 86986 Mod. status 252/19

3.2 Recipe

The setpoints associated with a product or a format are united in a recipe in ETC5000, i. e.,

every recipe represents a product or a format. Additionally, the name of the recipe as well as a

job-related instruction can be saved besides the target values. For more detailed information

refer to chapter 8.2: Recipe management –Editing recipes.

3.3 Operation / page navigation

ETC5000 is exclusively operated via the touchscreen. Input is possible via finger or any other

means (e. g. ballpoint pen, gloves, etc.). ETC5000 operating concept is divided into 4 main

areas.

(1) The history of selected menu items is located on the upper left margin of the page. The user

can return to the superordinate menu items via these operating elements.

Hint regarding the manual: This area guides the user to the menu items and

corresponding page where the desired function can be found.

(2) The fault and error area is on the bottom left margin of the page. The red warning triangle

appears when a fault or error occurs. The symbol is yellow with a critical battery voltage of a

device. You can obtain more detailed information by clicking on the button, e. g. the

defective axis and the type of error.

(3) Main information is always displayed in the center of the page. Actions or additional menu

items can be started or selected from that area.

(4) If a menu item has multiple pages (selection of axes and device parameters), the user can

toggle between the pages via the control elements on the right margin of the screen.

(1)

(2)

(3)

(4)

ETC5000 xDate: 12-11-2019 Page 5 of 23 Art. no. 86986 Mod. status 252/19

4 Login

A safety level protects nearly all functions of ETC5000. Therefore, the user should log in (1)

before starting. The login area is situated on the start screen and in the settings menu item.

The user can log in or off via this button. A window (2) opens where you select the user and log

in with a password. If no password has been defined yet, you can create one by repeated

entering new password twice. After logging in, the current user name and safety level is

displayed in place of the login button (3).

The current user is logged out (3) by pressing this button once more. When finishing work,

users should always log out because all actions on ETC5000 and the user logged in are

recorded in a log file.

5 Main functions / start screen

ETC5000 consists of the three basic functions "Axis Positioning", "Set Positioning" and

"Settings". These three main functions represent the basic framework of ETC5000 and enable

easy and effective monitored or automated format adjustment.

(1) Chapter 7: Axis Positioning: For setpoint specification and positioning of individual axes.

(2) Chapter 6: Set Positioning: For selecting and positioning recipes (all axes).

(3) Chapter 8: Settings: Managing recipes, configuring connected devices (also IO20), setting

the parameters of ETC5000, user account administration, importing and exporting device

configurations and recipes, log file and software update.

(1)

(2)

(3)

ETC5000 xDate: 12-11-2019 Page 6 of 23 Art. no. 86986 Mod. status 252/19

6 Set Positioning

This function constitutes the core function of ETC5000. The stored recipes can be selected

under Set Positioning. Afterwards, positioning of all axes is monitored and started.

6.1 Recipe selection

Under Set Positioning you can obtain a previously defined recipe (definition of Recipes see

chapter 8.2.1: Add recipe). For this purpose, choose the relevant recipe in the drop-down box

(1) and confirm it via the "OK" (2) button.

Recipe selection via the drop-down box (1) is no longer possible if IO20 has been set so as to

enable recipe selection. Recipes can be selected exclusively via IO20 in this case (see recipe

number). The recipe selected via IO20 is displayed in the drop-down box and also taken over

via the “OK” button.

You can search a recipe name via the "Magnifier" (3) button. It is sufficient to enter a part of the

recipe name into the search box (4). However, the text entered must start with the same

characters as the recipe name while caps and small letter use is not considered.

The search result (5) is displayed in a field, here you can select the desired recipe and confirm

by pressing the "OK" button (6).

Following confirmation of the selection, the setpoints of the recipe are transmitted to the

individual axes and the corresponding devices check that the axis is in position.

(1)

(2)

(3)

(1)

(2)

(3)

(4)

(5)

(6)

ETC5000 xDate: 12-11-2019 Page 7 of 23 Art. no. 86986 Mod. status 252/19

6.2 Recipe positioning

The relevant functions and details of the set recipe are all indicated on the order page. When

leaving this page (also when switching over to the Details page), all drives will stop

automatically.

This is the only page where you can take over a selected recipe for positioning solely via IO20.

The function must have been selected under the IO20 settings (see recipe number, accept

recipe).

(1) Recipe name.

(2) System status: The message displayed is placed on a red background if one or more axes

are out of position. The background color of the message displayed turns green as soon as

all axes are in position. The background color of the message displayed turns yellow if

moving drives are connected. The status is also always described by a short text on the

display. If selected, the status of the "digital Input" input type of IO20 is displayed as well.

(3) The start and stop buttons are only displayed if drives are connected. They are used for

starting or stopping positioning of the axes controlled by drives. The start button can also be

inactive if the correct status is not applied to the "drives enable" input of IO20.

(4) By pressing the "Details" button you get to an overview of all axes. The position values of

every axis are displayed here. Furthermore, a red or green point indicates whether or not

the axis is in position. As a result, the machine operator can quickly detect axes that are out

of position and require adjustment. A new setpoint can be written by clicking on the device

symbol and the axis can be adjusted.

(5) If the position was corrected directly on the axis, then the current position values of the axes

can be taken over as setpoints for the current recipe. Reading the current actual values,

their storage as setpoints for the recipe as well as transmission of the corrected setpoints

occur automatically after clicking on the "Teach In" button.

(6) If a job-related instruction was defined with the creation of the recipe, it is displayed in the

button margin of the screen. This area is grayed out if no job-related instruction was

defined.

(1)

(2)

(3)

(4)

(5)

(6)

ETC5000 xDate: 12-11-2019 Page 8 of 23 Art. no. 86986 Mod. status 252/19

7 Axis Positioning

The Axis positioning function can be used for positioning an individual axis. Via the "Axis

Positioning" button on the start screen you get to an overview of all connected devices. First

select an axis to be able to specify the target value of that axis. You need only tap on the device

symbol of the desired axis for this purpose. A window opens that enables the transmission of a

setpoint or traveling of the drives in inching mode.

7.1 Changing the setpoint of an axis and inching mode

You can specify a setpoint after selecting an axis. For this purpose, you must enter the desired

value into the "Target Value" (1) field and confirm it via the "transmit" (2) button. Afterwards, the

setpoint is automatically transmitted to the axis.

Additional control buttons are displayed for drives in the lower area of the window. You can start

the drives via the "Start" button (3). This induces drives to move automatically and to travel to

the setpoint. The current position of the axis (4) is always displayed above the setpoint.

The drives can be moved in inching mode via the arrow keys (5). Speed in inching mode can be

controlled via the bottom slide bar (6). Position indicators must be manually adjusted to the

setpoint. The current position of the axis (7) is always displayed above the setpoint. The lower

window area is not displayed with the position indicators.

NOTICE

The drives can always be started via the control buttons of inching mode

even if the "drives enable" IO20 function does not enable the drives!

There is a status display in the upper left window corner next to the device symbol (8), there is a

status display (9), which indicates whether the current axis has achieved the specified setpoint.

The status display glows green when the axis is on the setpoint (axis in position). Otherwise it is

illuminated red.

ETC5000 xDate: 12-11-2019 Page 9 of 23 Art. no. 86986 Mod. status 252/19

8 Settings

A few settings must be made in order to enable ETC5000 to monitor and control positioning

based on specified recipes. The setting menu is subdivided into 6 sub-menus:

(1) The individual setpoints of a products or formats axes are united in a recipe. Recipes can

be created, deleted or edited under the "Recipe Editing" menu item. The IO20 functions can

also be selected and changed here.

(2) The devices connected via SIKONETZ5 are displayed in the "Devicemanager". Here you

can add devices or change existing device configurations. The device parameters can be

viewed or changed here as well.

(3) The parameters of ETC5000 are pooled under "Settings ETC". Here you can change

language, the system time, screen brightness, and volume of ETC5000. Software update

can be performed here as well.

(4) User accounts can be created to enable the determination of individual user authorizations.

This and account administration are executed under "User Accounts".

(5) You can export the stored recipes, device configurations and the functions of IO20 to a USB

stick in order to facilitate copying and to save settings. Using the same menu item

("Import/Export"), you can import existing recipes-, device configurations- and IO20-files.

(6) The recorded events of ETC5000 are hidden behind the "Log File" menu item. You can also

export the log file to a USB stick under this menu item. Furthermore, you can determine

whether or not the file will be exported to a USB stick before resetting when it has reached

maximum size.

(1)

(2)

(3)

(4)

(7)

(8)

(9)

(5)

(6)

(5)

ETC5000 xDate: 12-11-2019 Page 10 of 23 Art. no. 86986 Mod. status 252/19

8.1 Device manager

8.1.1 Bus-Scan

The SIKONETZ5 bus is scanned before you actually get to the device manager. ETC5000

checks independently whether new devices were connected or whether all configured devices

are still correctly connected. A Pop-up (1) message indicates any new devices found or

discrepancies between the configuration file and the connected devices. No pop-up message

appears if ETC5000 has found everything to be correct, and the device manager will open

immediately. The number of new devices and of discrepancies is shown separately in the pop-

up message.

The user must decide whether to take over the results with the "tick" (2) or ignore them with the

"X" (3). After acknowledging or ignoring the results you can access the device manager.

If the user decides to take over the discrepancies, a pop-up message (4) will display again

every single discrepancy for every individual axis (device address).

(1)

(2)

(3)

(4)

(5)

(6)

(1)

(2)

(3)

Table des matières

Autres manuels Siko Unité de contrôle

Siko

Siko AS/2+MB Manuel d'utilisation

Siko

Siko AS510/1 Manuel utilisateur

Siko

Siko MA523/1-S Manuel utilisateur

Siko

Siko AS510 Manuel d'utilisation

Siko

Siko ASA510 Manuel d'utilisation

Siko

Siko MS02 Manuel utilisateur

Siko

Siko AS510/1 Manuel d'utilisation

Siko

Siko MS02 Manuel utilisateur

Siko

Siko AS510/1 Manuel utilisateur

Siko

Siko AEA111/1 Manuel d'utilisation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur