Siemens SIMATIC IFP Basic Series Manuel utilisateur
IFP Basic
SIMATIC HMI
Industrial Flat Panels Basic
IFP Basic
Operating Instructions
03/2019
A5E46178354
- AB
Preface
Overview
1
Safety information
2
Installing and connecting the
device
3
Commissioning the device
4
Operating the device
5
Maintaining and servicing
your device
6
Technical information
7
Technical Support
A
Markings and symbols
B
List of abbreviations
C
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: 6AV7862-2BC00-0AA0;6AV7862-2BD00-
0AA0;6AV7862
-2BE00-0AA0;6AV7862-2BF00-0AA0
Ⓟ
04/2019 Subject to change
Copyright © Siemens AG 2019.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
IFP Basic
Operating Instructions, 03/2019, A5E46178354 - AB 3
Preface
These operating instructions contain all the information you need for commissioning and
operation of the SIMATIC Industrial Flat Panels (IFP) Basic.
It is intended both for programming and testing personnel who commission the device and
connect it with other units (automation systems, programming devices), as well as for service
and maintenance personnel who install add-ons or carry out fault/error analyses.
Basic knowledge required
A solid background in personal computers and Microsoft operating systems are required to
understand this manual. General knowledge in the field automation control engineering is
recommended.
Scope of the operating instructions
These operating instructions apply to the following Industrial Flat Panels:
Product name
MLFB
SIMATIC IFP1200 Basic
6AV7862-2BC00-0AA0
SIMATIC IFP1500 Basic
6AV7862-2BD00-0AA0
SIMATIC IFP1900 Basic
6AV7862-2BE00-0AA0
SIMATIC IFP2200 Basic
6AV7862-2BF00-0AA0
Scope of this documentation
The SIMATIC IFP Basic is supplied with the following documents:
●In printed form: Quick Install Guide which includes the device description, installation and
commissioning Instructions.
●Electronically as PDF file on the "Tools, Drivers, and Documentation" DVD: SIMATIC IFP
Basic operating instructions.
●Electronically as PDF that can be download from Product Support in SIOS. The updates
of the document will be published in SIOS.
Conventions
In these operating instructions, the SIMATIC IFP Basic is also referred to as "IFP Basic" or
"device".
A touch device generally refers to a device with a touch screen, as opposed to a pure
"display device". Touch screen is the general term for a capacitive multi-touch screen and
resistive single touch screen.
Preface
IFP Basic
4Operating Instructions, 03/2019, A5E46178354 - AB
At some places in these operating instructions, the general term "Windows Embedded
Standard" is used to refer to "Windows Embedded Standard 7" . "Windows 7" is used as an
abbreviation for "Windows 7 Ultimate".
Figures
This manual contains figures of the described devices. The supplied device may differ in
some details from the figures. Within some of the figures, one device is used to represent all
SIMATIC IFP Basic.
History
Edition
Comment
03/2019
First Edition
IFP Basic
Operating Instructions, 03/2019, A5E46178354 - AB 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................. 7
1.1 Product description ...................................................................................................................7
1.2 Scope of delivery ......................................................................................................................8
1.3 Exterior design ..........................................................................................................................9
1.3.1 IFP Basic...................................................................................................................................9
1.3.2 Interfaces ................................................................................................................................10
1.4 Accessories.............................................................................................................................11
2 Safety information ................................................................................................................................. 12
2.1 General safety instructions .....................................................................................................12
2.2 Data protection........................................................................................................................14
2.3 Notes about usage..................................................................................................................14
3 Installing and connecting the device ...................................................................................................... 18
3.1 Preparing for installation .........................................................................................................18
3.1.1 Checking the delivery package...............................................................................................18
3.1.2 Identification data of the device ..............................................................................................20
3.1.3 Permitted mounting positions .................................................................................................21
3.1.4 Preparing the mounting cutout................................................................................................22
3.1.5 Checking clearances...............................................................................................................24
3.2 Installing the IFP Basic ...........................................................................................................25
3.2.1 Notes on installation................................................................................................................25
3.2.2 Secure with mounting clips .....................................................................................................26
3.2.3 Fastening a device using a VESA adapter .............................................................................28
3.3 Connecting the device ............................................................................................................30
3.3.1 Notes on connection ...............................................................................................................30
3.3.2 Earthing the device .................................................................................................................32
3.3.3 Connecting devices with 24 VDC 2-pin ..................................................................................33
3.3.4 Connecting IFP Basic to a PC ................................................................................................35
3.3.5 Connecting a USB device.......................................................................................................36
3.4 Installing the tool and driver....................................................................................................36
4 Commissioning the device .................................................................................................................... 39
5 Operating the device............................................................................................................................. 40
5.1 Operator input options ............................................................................................................40
5.2 Operating a device with resistive single touch screen............................................................41
5.3 Using the Brightness Adjustment Tool....................................................................................42
5.4 Using the touch driver .............................................................................................................43
Table of contents
IFP Basic
6Operating Instructions, 03/2019, A5E46178354 - AB
6 Maintaining and servicing your device ................................................................................................... 47
6.1 General information on maintenance and servicing .............................................................. 47
6.2 Cleaning the screen ............................................................................................................... 47
6.3 Spare parts and repairs ......................................................................................................... 48
6.4 Recycling and disposal .......................................................................................................... 48
7 Technical information............................................................................................................................ 49
7.1 Certificates and approvals ..................................................................................................... 49
7.2 Directives and declarations.................................................................................................... 51
7.2.1 ESD guideline ........................................................................................................................ 51
7.3 Dimension drawings............................................................................................................... 54
7.3.1 Dimension drawing of the IFP1200 Basic.............................................................................. 54
7.3.2 Dimension drawing of the IFP1500 Basic.............................................................................. 55
7.3.3 Dimension drawing of the IFP1900 Basic.............................................................................. 56
7.3.4 Dimension drawing of the IFP2200 Basic.............................................................................. 57
7.4 Rating plate ............................................................................................................................ 58
7.5 Technical specifications ......................................................................................................... 58
7.5.1 General technical specifications ............................................................................................ 58
7.5.2 Ambient conditions................................................................................................................. 60
7.5.2.1 Transport and storage conditions .......................................................................................... 60
7.5.2.2 Operating conditions .............................................................................................................. 61
7.5.2.3 Electromagnetic compatibility ................................................................................................ 62
7.5.2.4 Information on protection class and degree of protection...................................................... 64
7.6 Interface description............................................................................................................... 65
7.6.1 VGA interface......................................................................................................................... 65
7.6.2 24 VDC Power Supply ........................................................................................................... 65
7.6.3 DisplayPort............................................................................................................................. 66
7.6.4 USB interface, Type B ........................................................................................................... 67
7.6.5 USB interface, Type A ........................................................................................................... 67
A Technical Support................................................................................................................................. 68
A.1 Service and support ............................................................................................................... 68
A.2 Troubleshooting ..................................................................................................................... 69
B Markings and symbols .......................................................................................................................... 70
B.1 Safety-relevant symbols......................................................................................................... 70
C List of abbreviations .............................................................................................................................. 72
Glossary ............................................................................................................................................... 73
Index .................................................................................................................................................... 75
IFP Basic
Operating Instructions, 03/2019, A5E46178354 - AB 7
Overview
1
1.1
Product description
SIMATIC IFP Basic are touch monitors suitable for industrial use with a brilliant TFT (Thin
Film Transistor) display which can be connected to all SIMATIC IPCs as well as almost all
generally available PCs.
Features
●Rugged front
●Brilliant TFT display with a wide reading angle;
Resistive single touch screen in sizes 12", 15", 19" and 22"
●Can be placed up to 5 m from the IPC
●VGA and DisplayPort V1.2 interface
●Backlighting can be dimmed through software
●24 VDC power supply
Overview
1.2 Scope of delivery
IFP Basic
8Operating Instructions, 03/2019, A5E46178354 - AB
●Degree of protection IP65 for cabinet installation
●Up to 16 million colors
1.2
Scope of delivery
The product package includes the following components:
Name
Figure
Number
SIMATIC IFP Basic
1
Installation instructions
(Quick Install Guide)
1
Accessory kit
"Mounting clips
and
power supply connector"
20
1
"Tools, Drivers and Documenta-
tion" DVD
1
Overview
1.3 Exterior design
IFP Basic
Operating Instructions, 03/2019, A5E46178354 - AB 9
1.3
Exterior design
1.3.1
IFP Basic
This section describes the design of the monitor and touch devices, using the IFP1500 Basic
as an example.
Front view and side view
①
Display/touch screen
②
Interfaces
③
Recesses for mounting clips
Overview
1.3 Exterior design
IFP Basic
10 Operating Instructions, 03/2019, A5E46178354 - AB
Rear view
①
Rating plate
②
Holes for VESA mounting
③
Recesses for mounting clips
1.3.2
Interfaces
①
X80 connector for 24 VDC power supply
②
X72 VGA interface
③
X71 DisplayPort interface
④
X61, X62 USB 2.0 Type A
⑤
X60 USB 2.0 Type B
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Siemens écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
