Siemens SIMATIC WinCC V11 Guide de l'utilisateur
SIMATIC HMI
WinCC V11
WinCC Runtime Professional
Readme
System Manual
04/2011
Special considerations for
Windows 7
1
Installation
2
Runtime
3
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Ⓟ 04/2011
Copyright © Siemens AG 2011.
Technical data subject to change
WinCC Runtime Professional Readme
System Manual, 04/2011 3
Table of contents
1 Special considerations for Windows 7 ..................................................................................................... 5
2 Installation .............................................................................................................................................. 7
3 Runtime.................................................................................................................................................. 9
3.1 Notes on operation in Runtime ................................................................................................... 9
3.2 Notes on operation of Runtime Professional............................................................................. 10
3.3 Communication......................................................................................................................... 13
Index .................................................................................................................................................... 15
Table of contents
WinCC Runtime Professional Readme
4 System Manual, 04/2011
WinCC Runtime Professional Readme
System Manual, 04/2011 5
Special considerations for Windows 7 1
Contents
Information that could not be included in the online help.
Permission for the starting Runtime
To start WinCC Runtime Professional or WinCC Runtime Advanced, a user must be a
member of the automatically created group, "Siemens TIA Engineer".
Working with standard user rights
If you are working with standard user rights in Windows 7, "User Account Control (UAC)"
cannot be disabled.
The "User Account Control" is enabled in Windows 7 by default.
For more information on the "User Account Control, refer to the online help for Windows 7.
Special considerations for Windows 7
WinCC Runtime Professional Readme
6 System Manual, 04/2011
Slow response from the screen keyboard and SmartServer
The following programs may start and respond very slowly under Windows 7 and Windows
2008 servers:
● Microsoft OSK screen keyboard and HMI TouchInputPC
● SmartServer: <Ctrl+Alt+Del> shortcut in the logon dialog
The delay is caused by the callback for the Internet certificate validation.
Remedy:
Locate the following files on the product DVD under:
Support\Windows7\CRL_Check or CD_RT\ Support\Windows7\CRL_Check\
:
● DisableCRLCheck_LocalSystem.cmd
● DisableCRLCheck_CurrentUser.cmd
1. Run the "DisableCRLCheck_LocalSystem.cmd" file with administrator rights. Select the
command "Run as administrator" from the shortcut menu of the file.
2. Reboot the PC.
If the problem persists, follow these steps:
1. Double-click the file and run the "DisableCRLCheck_CurrentUser.cmd" file with user
rights.
2. Reboot the PC.
NOTICE
The callback for the certificate validation is disabled for all users or PCs. To restore the
original state, perform the following files:
•RestoreDefaults_LocalSystem.cmd
•RestoreDefaults_CurrentUser.cmd
You can find the files in the following directory of product DVD:
•Support\Windows7\CRL_Check bzw. CD_RT\Support\Windows7\CRL_Check\
WinCC Runtime Professional Readme
System Manual, 04/2011 7
Installation 2
Contents
Information that could not be included in the online help.
Operating system message for SIMATIC USB drivers
An operating system message relating to the SIMATIC USB driver is issued on the operating
system Windows Server 2003 R2 StdE SP2.
This message must be acknowledged with "Yes" as soon as possible after the message has
been issued. The message may be in the background and therefore not be immediately
visible. After a certain period of time, the setup continues with the next component. The
SIMATIC USB drivers are then not installed and can not be used.
Installation on a computer with regional setting "Turkish"
If the computer is operated with the regional setting "Turkish" at the time of the installation,
WinCC Runtime Professional cannot be started.
Installation via download
The supplementary installation of the WebNavigator client via download to the WebNavigator
server is not permitted.
Hotfix for SIMATIC NET
Install hotfixes for the following products:
● SIMATIC NET CD V8.0 SP1 for Windows 7: Hotfix 1 for SIMATIC NET CD V8.0 SP1
You can find the hotfixes in the Service & Support area of the Siemens website under the
entry ID 12660737.
SQL Server
During the installation of the SQL Server 2005 or the SQL Server 2005 Express, an error can
occur if the product SQL Server 2008 is already installed on your system.
In order to be able to use both varieties of the SQL Server in parallel. the SQL Server 2005
must be installed before the SQL Server 2008. To do this, follow these steps:
1. Remove the SQL Server 2008 version, without deleting the databases.
2. Install WinCC. The SQL Server 2005 is hereby installed and set up on your system.
3. Install the SQL Server 2008 again. Now you can continue to use the existing databases
in the SQL Server 2008.
WinCC Runtime Professional Readme
System Manual, 04/2011 9
Runtime 3
3.1 Notes on operation in Runtime
Contents
Information that could not be included in the online help.
CAUTION
Ethernet communication
In Ethernet-based communication, the end user is responsible for the security of his data
network. The proper functioning of the device cannot be guaranteed in all circumstances;
targeted attacks, for example, can lead to overload of the device.
Special characters in the user view
Special characters, such as / " § $ % & ' ?, are not permitted when entering a name or the
password in the user view.
Language behavior - Layout of screen keyboard
The layout of the screen keyboard is not switched when the runtime language changes.
Tag values overwrite the maximum length
You enter a character string in a string tag via an I/O field. If the character string exceeds the
number of configured tags, the character string will be shortened to the configured length.
Runtime
3.2 Notes on operation of Runtime Professional
WinCC Runtime Professional Readme
10 System Manual, 04/2011
3.2 Notes on operation of Runtime Professional
Contents
Information that could not be included in the online help.
User authorizations within the operating system
1. All user must be added to the "SIMATIC HMI" user group. This also applies to users who
want to open WinCC projects remotely.
2. The storage folders of the projects must have the NTFS authorizations "SIMATIC HMI"
with full access and "SIMATIC HMI Viewer" with read access. The authorizations must be
inherited for all subordinate objects.
3. Members of the Windows user group "SIMATIC HMI" should not simultaneously be
members of the Windows user group
"SQLServer2005MSSQLUser$<Computername>$WINCC". The members of this group
have administrator rights to the SQL server. Therefore remove all Windows users from
this group for whom restricted access to the WinCC database is sufficient.
Windows 7 / Windows Server 2008: Locking key combinations
If you want to lock key combinations under Windows 7 or Windows Server 2008, you must
change the group policies in the administrative tools of the operating system
A detailed description of this can be found in the FAQ with the entry ID "44027453" in the
SIMATIC Customer Online Support:
Internet: WinCC FAQ 44027453
(http://support.automation.siemens.com/WW/view/en/44027453)
Fault in the connection between the server and the client
If the connection between the server and client is faulty, check the settings of the PG/PC
interface. TCP/IP(Auto) should not be used for the "Interface Parameter Assignment Used".
Used fixed IP addresses instead.
Autres manuels pour SIMATIC WinCC V11
1
Table des matières
Autres manuels Siemens Écran tactile
Siemens
Siemens TP27 Document technique
Siemens
Siemens POL8T5.70/STD Guide de l'utilisateur
Siemens
Siemens POL8T2.40/STD Manuel de l'opérateur
Siemens
Siemens SIMATIC HMI TP27 Document technique
Siemens
Siemens Simatic PC Panel PC 870 Document technique
Siemens
Siemens SIMATIC SCD1900 Manuel utilisateur
Siemens
Siemens SIMATIC HMI TP 070 Document technique
Siemens
Siemens POL8T5.70/STD Manuel de l'opérateur
Siemens
Siemens SIMATIC Panel PC IL 77 Manuel utilisateur
Siemens
Siemens SIMATIC 677 Manuel utilisateur
Siemens
Siemens ZIC-8B Manuel utilisateur
Siemens
Siemens SIMATIC TP900 Comfort INOX PCT Guide de l'administrateur
Siemens
Siemens SIMATIC WinCC V11 Guide de l'utilisateur
Siemens
Siemens SIMATIC HMI TP 170A Document technique
Siemens
Siemens SIMATIC 870 V2 Manuel utilisateur
Siemens
Siemens 5WG1205-2AB21 Manuel utilisateur
Siemens
Siemens SIMATIC 677 Manuel utilisateur
Siemens
Siemens SIMATIC INOX Series Guide de l'administrateur
Siemens
Siemens Simatic PC Panel PC 870 Manuel d'installation
Siemens
Siemens 6AV3991-1AJ02-0AB0 Document technique
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
