Siemens TBM-2 Manuel utilisateur

P/N 315-093782-9

INTRODUCTION

The Model TBM-2 Termination Block module

from Siemens Industry, Inc., is the central

connection point for audio functions in the

MXLV System (See Figure 1). The ACM-1

Audio Control module communicates with

other modules in the system through the

TBM-2. In addition, the TBM-2 has connections

for the recording of telephone and microphone

messages, and the control connections to

activate recording equipment. Refer to the

CSG-M Manual, P/N 315-090381, to select

the Voice Options for your system.

The TBM-2 has two single pole, double throw

(SPDT) dry contacts, AUX CTRL1 and AUX

CTRL2, that control recording equipment.

When the microphone or telephone is active,

the signal goes to the chosen auxiliary output

and the corresponding control output changes

state. The TBM-2 does not include connectors

or cables for connecting the auxiliary outputs

and auxiliary controls.

The TBM-2 has a connection for an external

signal source. Use the AUX IN input and a

VSM-1 function to connect an external signal

source to the MXLV System. See Figure 4 for

information on input signals.

The TBM-2 provides screw terminal blocks

and connectors that interface the internal

wiring and field wiring (See Table 1).

For additional information on the MXL/MXLV

System, refer to the MXL/MXLV Manual, P/N

315-092036.

INSTALLATION

Remove all system power before installation,

first battery and then AC. (To power up, connect

the AC first and then the battery.)

The TBM-2 mounts on the right side of the

backbox next to the MMB or PSR-1, approxi-

mately one-third of the way down from the top

(Refer to Figure 2).

NOTE: In a Remote Extender enclosure the

TBM-2 mounts below the PS-5N7. Refer

to the PS-5N7 Instructions, P/N 315-092729.

Installation Instructions

Model TBM-2

Termination Block Module

TABLE 1

TBM-2 CONNECTIONS

Connector Connects

TB2 Digital Message Unit audio signal

connection

TB5 Supervised riser signals to System

(Style Y or Z)

TB4 Supervised telephone riser signal

(Style Y)

P1 SPDT contact to start the recorder for

AUX OUT 1

P2, P3 Plug-in cable power connections for

ACM-1

P4 Plug-in cable power connection for

VSM-1/VLM-1/VFM-1

P5 Plug-in cable power connections for

TMM-1

P6 SPDT contact to start the recorder for

AUX OUT 2

J1 AUX IN RCA type jack

J2 AUX OUT 1 RCA type jack

J3 AUX OUT 2 RCA type jack

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

WIRING

Refer to Figures 3 and 4.

All wiring must comply with

national and local codes.

For the audio and telephone risers:

Maximum wire size: 14 AWG twisted

pair, shielded

Minimum wire size: 18 AWG twisted

pair, shielded

Maximum loop resistance: 20 ohms for both

wires

Connect the 24 VDC to TB3 using 14 AWG

single conductor wire. Terminal 1 is for +24

VDC; terminal 2 is for 24 VDC return.

Refer to the CSG-M configuration printout to

determine the wiring style (either Style Y or

Style Z) for terminal block TB5.

For Style Z wiring, make the following connec-

tions:

• Connect terminals 1 and 4 in one cable going

out to Riser 1.

•

Connect terminals 2 and 3 in another cable

coming back from the last destination of

Riser 1.

• The other audio risers connect in a similar

fashion.

For Style Y connections, use only one cable.

Refer to Figure 3 for details.

Figure 1

TBM-2 Termination Block Module

Figure 2

Mounting the TBM-2

NOTE:

In a Remote Extender

enclosure, a PS-5N7 is

mounted above the TBM-2.

1. Before installing the module, mount the

PCB assembly to the mounting bracket

supplied using the four No. 6 screws

provided.

2. Place the TBM-2 assembly face up on the

three threaded studs arranged in a triangle

with TB5, the 15 position terminal block at

the top.

3. Secure the TBM-2 with the three No. 10

nuts provided.

Connect the riser cables to TB5 in the desired style,

using 18-14 AWG twisted, shielded pair. The other

ends of the risers connect to the OCC-1 terminal

block. Refer to the OCC-1 Installation Instructions,

P/N 315-090918, for further details.

For connections to other connectors and terminal

blocks, refer to the appropriate module installa-

tion instructions. (See also Figure 3 or Figure 4,

as appropriate.)

CAUTION: Keep the riser cables away from the AC power lines, the 24 VDC

supply lines, and the wires carrying the amplified audio signals.

Figure 3

TBM-2 Wiring Diagram

(with MMB or PSR)

1234

5678 91011 12 13 14 15

49 50

TB4

TB3

TB1

TB2

DV-100

OR DMC-1

DV-100

OR DMC-1

+-+-

TB5

J2 J3

NC NC

NO NOC C

14 14

TELEPHONE

RISER +

TELEPHONE

RISER -

TELEPHONE

RISER SHIELD

24V DC +

24V DC RETURN

TO ACM-1, P2

50 CONDUCTOR

RIBBON CABLE

TO VSM-1/VLM-1/VFM-1 MODULES

4 WIRE CABLE

TO ACM-1, P3

TO TMM-1, P1

5 WIRE CABLE

4 WIRE CABLE

NO CONNECTIONS

*EOL

CONNECTION AT FIRST OCC-1 TERMINAL BLOCK

CONNECTION AT SECOND OCC-1 TERMINAL BLOCK

CONNECTION AT LAST OCC-1 TERMINAL BLOCK

AUDIO RISER #1 AUDIO RISER #2

AUDIO RISER #3

CONNECTION AT FIRST OCC-1 TERMINAL BLOCK

CONNECTION AT SECOND OCC-1 TERMINAL BLOCK

CONNECTION AT LAST OCC-1 TERMINAL BLOCK INCLUDES EOL

STYLE Y

STYLE Z

NOT USED

TERMINATED

For Style Z connections, the lines

connected to terminals 1 and 4 are

in one cable. The lines connected

to terminals 2 and 3 are in another

cable. Connect the shield from the

cable connected to terminals 1 and 4.

Telephone Riser

Supervisory Voltage:

15 VDC -

With EOL = 5.6K

and no telephones in

off-hook state.

11 VDC -

With EOL = 5.6K

and one telephone

in off-hook state.

*EOL 10K, 5%, 1/2W

P/N 140-820396

14 AWG SINGLE

CONDUCTOR

14 AWG SINGLE

CONDUCTOR

For all Audio and Telephone Risers

Maximum Loop Resistance: 20 OHMS

Minimum Wire Size: 18 AWG twisted pair, shielded

Maximum Wire Size: 14 AWG twisted pair, shielded

NOTE:

24 VDC IS AVAILABLE ON

THE MMB OR PSR-1

24 VDC IS AVAILABLE ON

THE MMB OR PSR-1

ALL WIRING MUST COMPLY WITH

NATIONAL AND LOCAL CODES

ALL WIRING MUST COMPLY WITH

NATIONAL AND LOCAL CODES

AUX

CTRL 1

AUX

CTRL 2

AUX

OUT1

AUX

OUT 2

Refer to Wiring Specification

for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772

revision 6 or higher, for

additional wiring information.

Audio Riser

Supervisory Voltage:

3.65 VDC nominal

1V RMS AC

POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <50K OHMS FOR TERMINALS 1-14.

P/N 315-093782-9

Figure 4

TBM-2 Wiring Diagram

(with PS-5N7 in an Extender Enclosure)

WARNING

The user must comply with AUX IN and AUX OUT

specifications or the MXLV System may not function

properly. Always complete the full system test to

ensure that all applications function completely.

NOTES

1. All wiring must comply with National and Local codes.

2. For all Audio and Telephone Risers:

Maximum Loop Resistance: 20 ohms

Minimum Wire Size: 18 AWG twisted pair,

shielded

Maximum Wire Size: 14 AWG twisted pair,

shielded

3. Input impedance of AUX IN is 3K ohms, 200mV RMS.

4. The signal source must have isolation using a transformer.

5. The load impedance for AUX OUT must not be less than 10K

ohms, 200mV RMS.

6. The load must have isolation using a transformer.

7. SPDT contacts activate when audio is present on AUX OUT

jacks based on the CSG-M selection of microphone or tele-

phone. Contact ratings: 0.3A at 24 VDC

• If AUX OUT 1 is microphone, then AUX OUT 2 is telephone.

• If AUX OUT 1 is telephone, then AUX OUT 2 is microphone.

8. Refer to Wiring Specification for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772 revision 6 or higher, for additional

wiring information.

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm76

tnerruCeludoMCDV42ybdnatSAm06

Autres manuels Siemens Unité de contrôle

Siemens

Siemens K60R Manuel utilisateur

Siemens

Siemens SIMATIC Panel PC 677 Manuel utilisateur

Siemens

Siemens FCI1802-A2 Manuel utilisateur

Siemens

Siemens SIMOCODE pro Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens LAL Series Manuel utilisateur

Siemens

Siemens IM 328-N Instructions d'utilisation et d'installation

Siemens

Siemens SIMATIC IM 151/CPU Manuel utilisateur

Siemens

Siemens LMV52 series Manuel utilisateur

Siemens

Siemens SCALANCE W788C-2 Manuel utilisateur

Siemens

Siemens Simatic Net Scalance M812 Manuel utilisateur

Siemens

Siemens LMV 5 Series Manuel utilisateur

Siemens

Siemens MLC Manuel utilisateur

Siemens

Siemens RUGGEDCOM RS400 Manuel utilisateur

Siemens

Siemens SINAMICS DCM Manuel utilisateur

Siemens

Siemens OMM-2 Manuel utilisateur

Siemens

Siemens REMBOX2-MP Manuel utilisateur

Siemens

Siemens SITOP DC UPS 6EP1931-2DC21 Manuel utilisateur

Siemens

Siemens SIMATIC FM 351 Manuel utilisateur

Siemens

Siemens AS-Interface 3RK2402-2 00 Series Manuel utilisateur

Siemens

Siemens SIMATIC S7 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens ALD-2I Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur