Siemens MPS-6 Manuel utilisateur

Installation Instructions

Model MPS-6

Power Supply Module

P/N 315-090334-8

OPERATION

The Model MPS-6 from Siemens Industry, Inc. is a

fully supervised power supply that provides the MXL

System with primary 24 VDC power. It is rated at 6.5

amps and is unfiltered and unregulated. The MPS-6

supplies the MXL Control Panel or PSR-1 and its

expansion modules with the power required for

normal operation. The module incorporates a 2 amp

resettable circuitbreaker on the primary input and

includes a built-in AC line filter for surge and noise

suppression. The MPS-6 mounts in an MXL enclo-

sure backbox.

INSTALLATION

Always remove power before installation.

The installation kit for the MPS-6 includes the

following:

Four #10 nuts

Two #10 lockwashers

Two #10 flat washers

Two ¼" nuts

One 14 gauge green ground strap

The MPS-6 is designed to operate from a 120 VAC,

60 Hz power source. Use a separate or dedicated

circuitbreaker. Wire in accordance with local codes

and Article 760 of the NEC, NFPA 70, latest edition.

Run the earth ground from a suitable source to the

MPS-6. Check local requirements. Conduit is not

an acceptable conductor.

1. Make sure that the dedicated circuitbreaker

for the MPS-6 is turned off at the mains.

2. Place the mounting bracket for the MPS-6 over

the two studs provided in the enclosure. (Refer to

Figure 1.)

3. Secure the MPS-6 to the enclosure by slipping the

flat washers, then the lockwashers, and finally the

nuts over the two studs. Tighten them securely.

4. Connect the AC mains to the MPS-6:

Terminal

Black (hot) 1

White (neutral) 2

Green (earth ground) 3

5. Install the 14 gauge green ground strap spade lug

side to Terminal 3 (green, earth ground) of the

MPS-6. Secure the ring lug side of the ground

strap to the nearest available stud in the enclo-

sure. The stud size may vary depending on the

actual system modules and enclosure used.

Because the stud may be either a #10 thread or

¼" thread, nuts for both have been provided. The

ground strap provided is long enough for all

applications and the ring lug is good for both #10

and ¼" studs. If possible, install the ring lug under

one of the lock-washers and nuts which secure

the MPS-6 itself.

6. When used with a PSR-1:

Connect the 3-wire cable coming from the MPS-6

to the PSR at P12.

When used with an MMB-1/-2/-3 or SMB-1/2:

Connect the 3-wire cable coming from the MPS-6

to the MMB-1/-2/-3 or the SMB-1/2 at P1.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-090334-8

Figure 2

Front of MPS-6

Figure 1

MPS-6 in MXL Enclosure

POWER CABLE TO:

MMB-1/-2/-3, P1

SMB-1/-2, P1

PSR-1, P12

Autres manuels Siemens Unité de contrôle

Siemens

Siemens OZW771 Manuel utilisateur

Siemens

Siemens FDCI221 Manuel utilisateur

Siemens

Siemens LMV37.4 Series Manuel de l'opérateur

Siemens

Siemens TC45 Manuel utilisateur

Siemens

Siemens SIRIUS 3TK2834 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens LVM Manuel utilisateur

Siemens

Siemens ZIC-4A Manuel de service

Siemens

Siemens SINUMERIK 840C Manuel

Siemens

Siemens TM Timer DIDQ Guide de démarrage rapide

Siemens

Siemens SINUMERIK 840Di sl Manuel de la liste des pièces

Siemens

Siemens Cerberus Pyrotronics MT-30 Manuel utilisateur

Siemens

Siemens FDK:085U0321 Manuel utilisateur

Siemens

Siemens Simatic S7-1500/ET 200MP Document technique

Siemens

Siemens OLM/P11 V4.0 Manuel utilisateur

Siemens

Siemens SINUMERIK 805 Manuel utilisateur

Siemens

Siemens SIMATIC EP200SP Manuel utilisateur

Siemens

Siemens SIPLUS ECC8000 Manuel utilisateur

Siemens

Siemens SINUMERIK MC Guide de démarrage rapide

Siemens

Siemens SIPROTEC 7SJ80 Manuel utilisateur

Siemens

Siemens SINAMICS G130 Manuel utilisateur

Siemens

Siemens SIRIUS Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Guide de démarrage rapide

Siemens

Siemens SINUMERIK 840C Guide de configuration

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur