Siemens Milltronics TASS Manuel utilisateur

Operating instructions

Milltronics TASS

Speed Sensors

07/2018Edition

Milltronics

www.siemens.com/processautomation

___________________

Speed sensors

Milltronics TASS

Operating Instructions

07/2018

A5E45488881

-AA

Introduction

Description

Mounting

Connection

Technical data

Dimension drawings

Certificates and support

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: A5E45488881

Ⓟ

07/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Milltronics TASS

Operating Instructions, 07/2018, A5E45488881-AA 3

Table of contents

1 Introduction................................................................................................................................................ 5

1.1 Operating instructions scope ....................................................................................................5

1.2 Industrial use note.....................................................................................................................5

2 Description................................................................................................................................................. 7

2.1 Milltronics TASS overview ........................................................................................................7

3 Mounting.................................................................................................................................................... 9

3.1 Mounting location....................................................................................................................10

4 Connection .............................................................................................................................................. 11

5 Technical data ......................................................................................................................................... 13

6 Dimension drawings ................................................................................................................................ 15

6.1 TASS.......................................................................................................................................15

6.2 Mounting bracket ....................................................................................................................16

A Certificates and support........................................................................................................................... 19

A.1 Certificates ..............................................................................................................................19

A.2 Technical support....................................................................................................................19

Milltronics TASS

Operating Instructions, 07/2018, A5E45488881-AA 5

Introduction

1.1

Operating instructions scope

This instruction manual covers the installation, operation and maintenance of the TASS

Speed Sensor.

1.2

Industrial use note

Note

•

The TASS is to be used only in the manner outlined in this instruction manual.

•

This product is intended for use in industrial areas. Operation of this equipment in a

residential area may cause interference to several frequency based communications.

Introduction

1.2 Industrial use note

Milltronics TASS

6Operating Instructions, 07/2018, A5E45488881-AA

Milltronics TASS

Operating Instructions, 07/2018, A5E45488881-AA 7

Description

2.1

Milltronics TASS overview

The TASS trailing arm speed sensor is a compact, low-profile, wheel-driven return belt

speed sensor. The TASS has a sensor wheel and trailing arm assembly that rides along the

return belt. The sensor wheel rotates on a shaft fixed to the trailing arm. The internal

proximity switch detects rotation of the wheel, generating a signal proportional to belt speed.

The output signal is transmitted via cable connection to the integrator to determine the rate

of conveyed material.

Description

2.1 Milltronics TASS overview

Milltronics TASS

8Operating Instructions, 07/2018, A5E45488881-AA

Milltronics TASS

Operating Instructions, 07/2018, A5E45488881-AA 9

Mounting

The TASS speed sensor attaches to the static beam of the associated belt scale, or to a

structural cross member via a pivot and bracket assembly.

Do not allow the slope of the TASS arm to exceed 45° below the belt stringer line.

①TASS

②Milltronics belt scale

Note

Ensure that the wheel is in contact with the belt at all times.

Table des matières

Autres manuels Siemens Accessoires

Siemens

Siemens QNA2 D Series Mode d’emploi

Siemens

Siemens QFA3100 Manuel de service

Siemens

Siemens TC63 Guide de configuration

Siemens

Siemens 1218RF Manuel utilisateur

Siemens

Siemens HL 3000 Manuel utilisateur

Siemens

Siemens QAA2391.EWTC Manuel utilisateur

Siemens

Siemens RUGGEDCOM WIN7014 Manuel utilisateur

Siemens

Siemens SIWAREX WT241 Manuel utilisateur

Siemens

Siemens DELTA 5TC1 01 Manuel de service

Siemens

Siemens SIWAREX WP241 Manuel utilisateur

Siemens

Siemens HFPO-11 Manuel utilisateur

Siemens

Siemens QPM11 Series Manuel utilisateur

Siemens

Siemens SIMATIC VS120 Manuel utilisateur

Siemens

Siemens ADM-QXA12T Manuel utilisateur

Siemens

Siemens 3VL9400-4W.30 Manuel utilisateur

Siemens

Siemens SITRANS WFS320 Manuel utilisateur

Siemens

Siemens QGO21 Series Manuel de l'opérateur

Siemens

Siemens Simodrive SIMAG H Manuel utilisateur

Siemens

Siemens 3VL9500 - 4PA30 Manuel utilisateur

Siemens

Siemens Milltronics RBSS Manuel utilisateur

Siemens

Siemens SITRANS WS300 Manuel utilisateur

Siemens

Siemens enlighted SU-5i-USB Manuel utilisateur

Siemens

Siemens Sitrans WM100 Manuel utilisateur

Siemens

Siemens QAA2280.xWNC Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur