Siemens HL 3000 Manuel utilisateur

Ce manuel convient aux modèles suivants

2

Table des matières

Autres manuels Siemens Accessoires

Siemens

Siemens 3VL9400-4PJ00 Manuel utilisateur

Siemens

Siemens QMX3.P35H Series Manuel utilisateur

Siemens

Siemens QFM3100 Manuel de service

Siemens

Siemens Sitrans WM100 Manuel utilisateur

Siemens

Siemens QBM3700 Series Manuel utilisateur

Siemens

Siemens HC15 Manuel utilisateur

Siemens

Siemens SITRANS F M MAG 1100 Manuel utilisateur

Siemens

Siemens Symaro QAA2890/WI Manuel utilisateur

Siemens

Siemens QMX3.P30 Manuel utilisateur

Siemens

Siemens Opto-BERO K50 Manuel utilisateur

Siemens

Siemens S 564 Manuel utilisateur

Siemens

Siemens 3VL9500 - 4PA30 Manuel utilisateur

Siemens

Siemens SIWAREX JB Guide de l'administrateur

Siemens

Siemens QFA2000 Manuel utilisateur

Siemens

Siemens 3200 Series Manuel utilisateur

Siemens

Siemens QAF63 Series Manuel d'instructions

Siemens

Siemens SITRANS F C MASS 2100 DI 1.5 Manuel utilisateur

Siemens

Siemens QGO21 Series Manuel de l'opérateur

Siemens

Siemens SIMATIC RF300 Guide de l'utilisateur

Siemens

Siemens AP 257/41 Manuel utilisateur

Siemens

Siemens Simodrive SIMAG H Manuel utilisateur

Siemens

Siemens Milltronics MD-36 Manuel utilisateur

Siemens

Siemens WiPS-200 Series Manuel utilisateur

Siemens

Siemens 6DR4004-6NN Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur

Your

eye

in

hell

HL 3000 Manual

© Siemens Laser Analytics Sept 2000

Halogen lamp alignement manual

Document number: CID 3002-1103 Rev. 1A

LDS 3000 Operators manual HL 3002

1

1. HL 3002

1.1 General

Sometimes the visibility in the measurement path is poor. The reason for

this might be high dust load, smoke or strong ambient light from the

process (as in a combustion chamber). In this case a stronger light source

must be used in the first alignement step. Siemens Laser Analytics AB

can supply a suitable light source labelled HL 3000. This is a point source

using a 50 W halogen lamp and will produce a very luminous light spot -

normally easy to spot in the alignement procedure.

HL 3002 LDS 3000 Operators manual

2

1.2 The alignement procedure

The sensor is aligned using the sensor alignment kit AK 3002 together

with HL 3000. The aligning procedure is as follows:

Receiver side

1. Start by aligning the transmitter side. This is done by removing the

receiver at the quick connect interface and instead mount HL 3000

which defines the optical axis of the sensor pair. While the receiver is

dismounted - check that the lens is clean on the receiver and that the

purging is working.

Receiver side

HL 3000 generates a considerable amount of heat. Protective gloves should be ised

when it is handled.

Halogen alignement lamp

Note!

LDS 3000 Operators manual HL 3002

3

Transmitter side

2. Dismount the transmitter and check that the lens is clean on the

transmitter and that the purging is working. Then mount the trans-

mitter and twist-dismount the launcher (fiber cable connector in the

middle), twist-mount the cross hair instead. Align with the four bolts

on the flange, the light dot must be centred in the inner ring of the

cross hair.

Transmitter side

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

4

Transmitter side

3. Twist-mount the alignement lamp instead of the cross hair in the

transmitter.

Transmitter side

Alignement lamp

LDS 3000 Operators manual HL 3002

5

Receiver side

4. Mount the receiver back again and twist-mount the cross hair

instead of the detector module. Align with the four bolts on the

flange, the light dot must be centred in the inner ring of the cross

hair.

Receiver side

CD 3002 is now aligned and the holder for the fibre connector and the de-

tector module should be mounted in their places.

Finally, instrument air, or which ever method is used to protect the opti-

cal surfaces, should be connected to the appropriate inlets both at the

transmitter and receiver side of the sensor.

The mechanical stability of the sensor mechanics is sufficient to allow

dismounting (the quick connection) of both the receiver and the trans-

mitter. This means that cleaning of the lenses does not require re-align-

ment of the sensor.

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

6