SEWOO LK-P32 Manuel utilisateur

All specifications are subject to change without notice

MOBILE PRINTER

MODEL : LK-P32

P32 Rev. A 08/14

SEWOO TECH CO.,LTD.

374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea

TEL : +82-31-459-8200 FAX : +82-31-459-8880

www.miniprinter.com

Table of Contents

Safety Caution 2

Unpacking

Product Overview 5

4. Usage and Installation 6

4-1. Control panel usage

4-2. Battery installation

4-3. Battery removal

4-4. Battery charging

4-5. Roll paper installation

4-6. Self test

Peripherals Connection 16

5-1. Bluetooth connection

5-2. Interface cable connection

6. P

rinter Specificaiton 18

6-1. Specification

For higher reliability and safety, consider the following precautionary measures.

Read and follow the instructions carefully before running of the product.

1. Safety Caution

WARNING

Failure to follow these instructions could result in re, electric shock,

or other injuries, or property damage

Indication

Prohibition

(Potential risk of electric shock or re)

(Potential risk of electric shock or re) (Potential risk of electric shock or re)

(Potential risk of electric shock or re)

Must follow

Do not disassemble Unplug the power from the

outlet

Grounding to prevent electric

shock

Do not handle the product

with wet hands

Do not pull or touch the power plug with

wet hands.

Do not bend the wire and do not allow the

wire to be pressed by heavy object.

If a power plug is broken or a plug is cut or

worn, do not use it.

Do not overload the power plug into one

outlet.

WARNING

Failure to follow these instructions could result in re, electric shock,

or other injuries, or property damage

Failure to follow these instructions could result in re, electric shock,

or other injuries, or property damage

(Turn off the power at installation,

transportation, wiring and inspection.)

(You may get hurt and it can be broken

when it falls)

(Potential risk of re or unit malfunction)

(Potential risk of discoloration or

electric shock)

(Potential risk unit malfunction, electric

shock or re. When the product needs

to be repaired, please contact in place

where you ordered.inspection.)

Dealer

Do not pull out the power plug to turn off

the product.

Do not install the product in uneven or

inclined surface.

If the product that needs to be repaired,

please contact in place where you ordered.

Please do not give excessive shock.

Keep product away from the water and

other material.

Do not disassemble, repair or modify the

product.

CAUTION

3. Product Overview

Open

button

LCD

Power

button

Battery

USB

Front

Rear

2. Unpacking

Paper feed

button

Control

button

PrinterPrinter

Roll paper

USB Cable

Battery CD

Standard

Charger

4-1-1. Printer status icons

4. Usage and Installation

On Line

No Paper

Head Cover Open

Printing

On Line

Bluetooth Battery

No Paper

Cover Open

Now Printing

※

Emulation Information

On Line

ESCPOS

Emulation Information

On Line

CPCL

TPH Overheated

Head Overheated

4-1-2. How to check the remaining power

The battery lamp in LCD signify

the remaining power.

Low Battery

Full Low Battery Flat

4-1 Control panel usage

Button

Name

function

Power

button

This button is used to turn the printer on and off.

When the printer is off, press this button for approximately

3 seconds and it will turn on the power. When you press

this button in a state that the printer is on, the printer will

turn off.

Paper

feed

button

Paper output can be done manually by pressing this button.

Additionally, self-testing and Hexadecimal Dumping can

be processed..

Press to scroll through the menu choices on the LCD.

Setting Press to select a menu choice on the LCD.

4-1-3. Configuration setting

Media : Current Media

Parameter Action/Explanation

Current Media

Displays the Media type that is currently set

Media Type: Journal

BlackMark

Label

To verify Media Type

1. Press button once to display the current

Media type.

Parameter Action/Explanation

Auto Gap or BM (Black Mark) and BAT

(Battery) Calibration

Mode: Gap or BM Calibration

BAT (Battery) Calibration

To Perform Calibration Auto Setting

1. Press button 3 times.

2. Press button to execute Gap or BM

and Battery calibration and wait for 3 seconds.

LCD will display "Are you sure?"

3. Press button to double conrm and printer

will automatically execute auto setting. If not,

wait for 3 seconds without pressing any button.

It will automatically go back to main menu.

※ Navigate the LCD menus by pressing button.

Auto Setting

NOTE

To do BAT(Battery) Calibration, REMOVE Battery and use charger only.

In case of using Journal Media mode, Gap or BM calibration will not be displayed.

CAUTION

To change the Media type, use Conguration Tool or LKPxxInitialSetting Utility.

Parameter Action/Explanation

Adjust Print Density

Adjust printing resolution manually.

Density Value: 1~9

To change the value shown

1. Press button twice.

2. Press button to adjust Density.

3. If you do not change any density value,

it will automatically go back to main menu

in 3 seconds.

4. Wait 3 seconds after adjust the density value,

LCD will display "Saving...?".

Then Press button to save or wait

3 seconds not to save.

Manual Setting

10 11

1. Align battery hook as shown in the picture

2. Push the battery into the printer until it locks in place.

As the battery is not charged at the time of your purchase, charge the

battery prior to using the printer

(Use Battery charger or Cradle to charge)

Hook

4-2 Battery installation

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions

Remove the battery holding it up as shown above.

4-3 Battery removal

CAUTION

NOTE

12 13

4-4 Battery charging

1. Unless the exclusive charger is used provided by the manufacturer, the printer

can be damaged, and the manufacturer is not liable for the consequential damage.

2. Before removing the battery, make sure that power is turned off.

3. Printer does not work in the status of being connected with charger only.

4. The battery should be installed to operate printer.

5. While charging, do not turn on the power.

6. Do not operate the print while charging the battery.

7. Do not connect the charger while the printer is operated.

1. Be sure that the printer is turned off

2. After open the USB JACK cover, insert USB JACK into the printer.

3. Plug the power code to electrical outlet.

4-4-1 The status of lamp in charging

Status Charging Charging complete Charging stand by

Charging Lamp Red

Green Green

LED

1 2

Press the PUSH button to open the

paper cover

Pull a short length of paper out of the

printer and close the cover.

Insert the paper in the right direction

Tear off the additional paper using

tear bar.

4-5 Roll paper installation

NOTE

14 15

1 2

Turn off the power pressing the

power button for approximately

3 seconds.

The printout is produced.

While you are pressing the FEED

button, press the power button

4-6 Self test

When the printer is installed initially or when you face a problem, you can run the self

test and check the information about

-Control Circuit, Mechanism, Print Quality, ROM Version

After checking with self-test and no issues are found, you can examine other devices and

software. This function is working independently of devices and software.

●

Motor protection from being overheated

The motor should be stopped and cooled about more than 30 seconds after

continuous printing 1.5 meter

The sample of self test printout

1. To print ASCII pattern additionally,

press the Feed button once more

2. After printing ASCII pattern, the

self test will be finished automatically.

3. If the Feed button is not pressed

to print ASCII pattern, self test will

be finished automatically after 30

seconds.

NOTE

16 17

1. Printer can be connected to the PDA and PC which can do wireless

communication.

2. By using Bluetooth function supported in PC, printer can be connected.

This printer can communicate with peripheral devices via Bluetooth and

cables.

5-1 Bluetooth connection

5. Peripherals Connection

Refer to the

Bluetooth

Manual for more details on connection.

5-2 Interface cable connection

1. Connect USB into the cable connector on the printer.

2. Connect the interface cable into the USB or Serial port

of the device (PDA, PC, etc.)

Use the cable offered by the manufacturer (USB)

USB

NOTE

Table des matières

Autres manuels SEWOO Imprimante

SEWOO

SEWOO LK-P43 Guide de l'utilisateur

SEWOO

SEWOO SLK-TL21 Series Manuel utilisateur

SEWOO

SEWOO SLK-T20EB Series Manuel utilisateur

SEWOO

SEWOO SLK-TS400EB Manuel utilisateur

SEWOO

SEWOO SLK-T21EB Series Manuel utilisateur

SEWOO

SEWOO LK-P41 Instructions d'installation

SEWOO

SEWOO LK-P34 Manuel utilisateur

SEWOO

SEWOO SLK-TE122 Manuel utilisateur

SEWOO

SEWOO SLK-TE21X Series Manuel utilisateur

SEWOO

SEWOO LUKHAN LK-P21B Manuel utilisateur

SEWOO

SEWOO LK-P SERIES Feuille d'instructions

SEWOO

SEWOO LK-P22 Manuel utilisateur

SEWOO

SEWOO LK-P400 Manuel utilisateur

SEWOO

SEWOO LK-P43 Manuel utilisateur

SEWOO

SEWOO LK-D10 Manuel utilisateur

SEWOO

SEWOO LK-P20W Manuel utilisateur

SEWOO

SEWOO SLK-T213EB Series Manuel utilisateur

SEWOO

SEWOO SLK-TE32 Series Manuel utilisateur

SEWOO

SEWOO SLK-TE21X Series Manuel utilisateur

SEWOO

SEWOO TL32 Series Manuel utilisateur

SEWOO

SEWOO LK-P22 Manuel utilisateur

SEWOO

SEWOO LK-P400 Manuel utilisateur

SEWOO

SEWOO LK-T210 Manuel utilisateur

SEWOO

SEWOO LUKHAN LK-P21B Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur